urbanista 45381 ANC Wireless Headphones User Manual

urbanista 45381 ANC Wireless Headphones

Overview

URBANISTA LOS ANGELES
Thank you for choosing an Urbanista product.

FIRST TIME PAIRING AND RECONNECTING

Press and hold the “Control Button” (1) for 1 second. Your headphones will turn on and automatically enter pairing mode. Open Bluetooth settings on your device and select “Urbanista Los Angeles”. The “Battery Status Indicator” (2) will flash to indicate pairing mode and stop flashing when successfully paired. The headphones will automatically reconnect to the same device you have paired them to when next turned on.

CONNECT TO ANOTHER DEVICE
Disconnect the headphones from the device to enter pairing mode again or to connect to another device. The headphones can store up to six paired devices.

CHARGING AND BATTERY

Urbanista Los Angeles has a built-in PowerfoyleTM solar cell that continuously charges your headphones whenever exposed to any light providing you with virtually infinite playtime. The self-charging occurs in direct and indirect solar light as well as indoor light, but the stronger the light, the more effective. When you are not using your headphones, place them somewhere where the PowerfoyleTM area is exposed to light, for example, a windowsill. Should the battery for some reason run low, a “Battery low” voice prompt will notify you when there are 30 minutes of playtime remaining, after which the headphones will automatically turn off. Use the included USB Type-C cable connected to a power source to charge the headphones. The “Battery Status Indicator” (2) will lit red continuously when charging and turn white when fully charged.

CONTROLS

• POWER ON – Press and hold the “Control button” (1) for 1 second.
• POWER OFF – Press and hold the “Control button” (1) for 5 seconds.
• PLAY – Press the “Control button” (1) once.
• PAUSE – Press the “Control button” (1) once.
• ANSWER A CALL – Press the “Control button” (1) once.
• END A CALL – Press the “Control button” (1) once.
• REJECT A CALL – Press and hold the “Control button” (1) for 2 seconds.
• VOLUME UP – Press the “+” button (3) once.
• VOLUME DOWN – Press the “–” button (3) once.
• NEXT TRACK – Press and hold the “+” button (3) for 2 seconds.
• PREVIOUS TRACK – Press and hold the “-” button (3) for 2 seconds.
• ACTIVE NOISE CANCELLING – Press the “Feature button” (4) one time.
• AMBIENT SOUND MODE – Press the “Feature button” (4) a second time.
• DEFAULT MODE – Press the “Feature button” (4) a third time to return to default mode.
• VOICE ASSISTANT – Press the “Feature button” (4) for 2 seconds.

TROUBLESHOOTING

If you have any additional questions, please visit our online help center where you will find our FAQs and an online version of this manual:
https://support.urbanista.com/.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution:
Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

ISED Statement
English: This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license- exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

References

• Designed for life in motion | Urbanista | Urbanista Official Store
• SUPPORT CENTER | Urbanista Official Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>