CUBE TAMP K08021H09 Automatic Electronic Coffee Tamper Instruction Manual
- June 13, 2024
- CUBE TAMP
Table of Contents
AUTOMATIC ELECTRONIC
COFFEE TAMPER
INSTRUCTION
MANUAL
SAFETY
READ THE SAFETY AND USE INSTRUCTIONS CAREFULLY BEFORE FIRST USING THE APPLIANCE
This device should only be used for the function for which it was designed:
tamping ground coffee.
Do not use the device to press any other types of food such as nuts or
granulated foods such as sugar and others.
This device may be used by children aged 8 years and over, by people with
reduced physical, sensory or mental capacities and by people without prior
experience/knowledge, provided they have received supervision or instructions
on the safe use of the device and understand the associated risks.
Children should not play with the device.
Cleaning and maintenance of the device should not be carried out by children
without supervision.
Do not allowing liquids to come into contact with internal or external
surfaces while the appliance is on or off, except for those parts expressly
mentioned in the “CLEANING” section.
If, for any reason, this happens, disconnect the power supply immediately and
dry all surfaces carefully.
If it is necessary to access the interior, where the electrical components are
located, go to the nearest technical service
In the event of any component breaking, or for any intervention we recommend
contacting a technical services centre, who will carry out the repair or
replacement, guaranteeing that safety standards are adhered to.
Only an authorised supplier may replace the mains cable of any machine.
Any other use will be considered improper and dangerous
When maintaining the coffee tamper, special care should be taken as it could
cut the maintainer.
The use of suitable gloves when handling it is recommended.
Do not insert any part of the body between the coffee tamper and the holder.
NOTE: The manufacturer will not be liable for damages caused either by the improper use of the device or by not following the stated safety measures
DESCRIPTION
The coffee tamper you have purchased has been designed using the most
innovative technological systems.
The result is a high quality product that ensures the best results.
Our products are manufactured entirely by hand, one at a time, following the
most demanding quality requirements.
In its manufacturing process, quality materials (aluminium, steel, etc.) are
used, which are suitable for contact with food.
INSTRUCTIONS
3.1. This manual provides the information necessary for the correct
installation, handling and maintenance of the equipment and highlights the
precautions that should be taken by the operator.
To ensure you get the best out of the machine, it is essential to carefully
follow the instructions given in this manual.
If there is any kind of problem, contact the nearest technical service.
This manual should be kept until the machine is replaced and must always be
available to the operator.
3.2. This manual uses some special terms, such as:
- Text in bold to highlight the importance of some terms.
- Numbers in parentheses after a word, which match the numbering of the items in the image to the side or in the image of the external components.
Example: (1) – 1 Display
Icons:
| Information | Attention |
|---|---|
IDENTIFICATION
NOTE: The manufacturer reserves the right to change components/configurations of any model, according to the different geographic market demands.
TECHNICAL CHARACTERISTICS
5.1. SCOPE
The coffee tamper that you have purchased is intended for shops and
communities ground coffee needs to be tamped and it should only be used for
this purpose.
Any other use is considered improper and dangerous.
NOTE: The manufacturer will not be held responsible for any damages resulting from improper use of the equipment, or for not following the safety measures as outlined below.
110/220/240 V 50/60 Hz
Voltage/Frequency| 65| W
Weight| Height
Width
Depth| Tamp diameter
6,3| 290,3
1 6 7,7
185,0| See identification plate
Kg| mm| mm
XTERNAL COMPONENTS
INSTALLATION
7.1. LEGAL WARNINGS
The installer must read this instruction manual carefully before installing
the machine
The installation of the device must be carried out by qualified and authorised
personnel, in compliance with the current safety and hygiene standards
7.2. IMPORTANT WARNINGS
The operator must be a responsible adult. Never a child nor someone without
the ability to accept that responsibility
When handling the machine, the following precautions should be obeyed:
- Feet must not be bare.
- Hands and feet must be dry.
- Do not get the machine wet.
- Do not expose the machine to direct sunlight or other atmospheric agents.
- Never insert any part of the body between the tamp area and the support
- When unplugging the grinder, always pull on the plug and never the power cable to avoid a possible short circuit.
7.3. WHERE TO USE IT
The appliance must be installed on a solid, flat surface.
The minimum size of the workplace, to ensure the best performance of the
device, must be at least the following:
Height| 310
12.20| mm
in
---|---|---
Width| 188
7.4 0| mm
in
Depth| 205
8.07| mm
in
7.4. INSTALLATION
Before connecting the machine, check the following:
- The characteristics on the data plate match those of the electrical mains network.
- The electrical connection plug matches the socket into which it is to be plugged.
- Ensure that the electrical power of the facility is adequate for the power consumed by the appliance.
- The point of connection to the electrical mains network must be protected with the appropriate electrical protection device.
- The equipment must be correctly connected to a ground connection according to the current safety regulations.
OPERATION
8.1. POWER SWITCH
The power switch ( 9 ) has 2 positions: ( )
: Equipment on
o : Equipment off
8.2. FITTING THE PORTAFILTER
It is essential that the portafilter is perfectly adjusted to achieve a
consistent and level tamping.
Make sure that the diameter of your portafilter matches that of your Cube
Tamp’s coffee tamp.
Permitted height of the portafilter:
Minimum: 26,80 mm (1,055 in)
Maximum: 41,05 mm (1,616 in)
To adjust the support height:
Make sure the power switch ( 9 ) is in the OFF position.
Loosen the locking wheel ( 10 ) counterclockwise with the supplied tool. Fig.
1
Turn the adjustment wheel ( 8 ) clockwise to lower the support,
counterclockwise to raise it. Adjust the fork to the optimum height for the
portafilter as near to the top as possible. Fig. 2
While blocking with your fingers any movement of the adjusting wheel ( 8 ),
tighten the locking wheel ( 10 ) clockwise using the supplied tool. Fig. 3
NOTE: The manufacturer reserves the right to vary the components of the machine, according to the requirements of each market, as well as technological advances.
8.3. USE
The Cube Tamp is factory calibrated to a force of 20 kg.
If you want to save another default value to appear upon start up, turn on the
main switch (9) and press the + button (3) while the Cube logo appears on the
display during initialization. When the Cube logo blinks, increase or decrease
the Kg using the – (2) and + (3) buttons and confirm the selection with the
CLEAN ( ) button.
- Turn on the power switch ( 9 )
- Insert the portafilter into the support ( 7 ) until it reaches the bottom. Its presence will be detected automatically and the coffee tamp will lower until it exerts the desired pressure
- When the message ( ) appears on screen ( 1 ) you can remove the portafilter . Fig. 4
8.4. TAMPING FORCE REGULATION
The tamping force can be adjusted from 10 to 30 kg or from 22 to 66 lbs (this
option must be factory set).
The default force is 20 kg or 44 lbs
To increase the force use the + button ( 3 ) and to decrease it use the –
button ( 2 )
8.4.1 CONFIGURATION LBS. AND KG.
To change between KG and LB you need to:
-
Power off the unit.
-
Power on the unit and touch the CLEAN icon when the word CUBE appears on the screen, which happens almost as soon as the machine turns on. Don’t touch the screen until CUBE appears.
-
“KG LB” will then show up on the screen
-
You will touch the “-” or “+“ depending on whether you want KG or LB
In the case of Ibs., the units will increase or decrease 2 by 2.
8.4.2 CONFIGURATION °C AND °F
After choosing between KG or LB:
-
“°C °F ” will appear on the screen.
-
Press “-” o “+” depending on whether you want °C (Celsius degrees) or °F (Fahrenheit degrees). You have 10 seconds to select.
Once the selection has been made, the Cube will restart with the new configuration.
8.4.3 LOCKED KEYBOARD
To lock the digital display, simply press the + (3) and – (2) keys
simultaneously for 3 seconds until the lock icon appears. Fig. 5 To unlock
the digital display just repeat the same steps until the unlock icon appears.
Fig. 6
8.5. CLEANING MODE
For a correct tamping consistency, daily cleaning of the tamping disk is
recommended.
To do this, press the CLEAN button.
The disk will lower to the pressing position and stay there for 10 sec. During
this time you can clean it with a brush, or cloth if the disc is wet.
Press the CLEAN button again to return the disk to its idle position.
If you want the disk to remain in the pressing position to allow more time for
the cleaning, switch off the appliance using the switch ( 9 )
NOTE: The grinder shouldn’t be used in environments (SUCH AS INDUSTRIAL
KITCHENS) where cleaning is done with direct water spray cleaning.
TROUBLESHOOTING
DECLARATION OF CONFORMITY
In accordance with European community directives, quality certificates have
been applied. All materials have been adapted and technical reports are
available at our offices.
2014/30/UE on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
06/42/EC amending Directive 95/16/EC on the approximation of the laws of the
Member States relating to machinery
REG. 1935/2004 amending Directive 89/109/EC on the approximation of the laws
of the Member States relating to material and objects destinated to make
contact with nutritional products.
03/108/EC amending Directive 2002/96/EC on waste electrical and electronic
equipment (WEEE).
2014/34/UE on the harmonization of the laws of Member States relating to
electrical equipment designed for use within certain voltage limits.
2012/19/UE of 04/07/2012 on the approximation of the laws of the Member States
on waste electrical and electronic equipment (WEEE).
11/65/EU related to the restriction on the usage of certain dangerous
substances with electrical equipment and electronics.
Environment
Do not throw the applianceaway with the normal household waste; hand it in at
an official recycling collection point. By doing this, you will help to
preserve the environment.
The Legal Representative
Compak Coffee Grinders, s.a.
Molí Barri, Parcela B – Pol. Ind. Can Barri – 08415 Bigues i Riells –
Barcelona – Spain
Ph. 34 93 703 13 00 – Fax 34 93 703 13 23 –
www.compak.es Original Instructions
Ref. quality process 002/03 | v. 01/09/2022 | K08021H09
CONTACT
Molí Barri, Parcela B
Polígono Industrial Can Barri
08415 Bigues i Riells
Barcelona – Spain
Phone: +34 93 703 13 00
Fax: +34 93 703 13 23
E-mail:
info@compak.eswww.compak.es