Lasko CS27600 Ceramic Pedestal Heater with Remote Control Instruction Manual

: June 5, 2024
: Lasko

Table of Contents

Lasko CS27600 Ceramic Pedestal Heater with Remote Control
IMPORTANT SAFETY INSTRUCTIONS
Parts Included
Assembly
Controls
SAVE-SMART® FUNCTION
AUTOMATIC TEMPERATURE CONTROL
SAFETY FEATURE
MAINTENANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lasko CS27600 Ceramic Pedestal Heater with Remote Control

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, these instructions and warnings should always be followed to reduce the risk of fire, electrical shock and injury to persons:

WARNING

PLUG HEATERS DIRECTLY INTO A 120V WALL OUTLET/RECEPTACLE ONLY. NEVER USE WITH AN EXTENSION CORD. DO NOT PLUG THE HEATER INTO ANY OTHER CORD-CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET ADAPTER, CORD REEL, OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. DO NOT PLUG MULTIPLE DEVICES IN THE SAME OUTLET OR ON THE SAME CIRCUIT AS THE HEATER.
FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT THE HEATER PLUG FITS TIGHTLY INTO THE OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER WITH ANY SOLID-STATE SPEED CONTROL DEVICES.
Make certain that the power source conforms to the electrical requirements of the Heater.
Extreme caution is necessary when any heater is used by or near children or invalids. The Heater should not be left operating unattended. Never leave children unattended when the Heater is on or plugged in.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use a Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres.
Do not operate any heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner. To dis-connect, the Heater, turn the Heater OFF then remove the plug from the outlet.
Always unplug the heater when not in use. Unplug the power cord before servicing or moving the Heater.
Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage to the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not depend on the on/off switch as the sole means of disconnecting power when servicing or moving the Heater. Always unplug the power cord.

CAUTION

Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners, or similar coverings as this may cause cord to overheat. Arrange Power Cord away from room traffic and where it will not be tripped over.
This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear. This Heater is not intended for use in wet or damp locations.
This Heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
DO NOT use Heater outdoors.
This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings. THIS Heater DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations. THIS Heater DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008). Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Heater. If this occurs, move the Heater to another location.
Keep Heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Heater.

Parts Included

Body
Thumb Screws
Column Support A
Column Support B
Remote Control
Support Base A
Support Base B

Assembly

Place the Power Supply Cord through the Column Support and snap it together. Insert into the bottom of Body.
Turn Body face down and twist clockwise to lock. Use Thumb Screw to secure the column to Body.
Push the Bosses on Support Base B into the Boss Slots on Support Base A.
At tach the Base As sem bly to the Column Support As sem bly with (4) Thumb Screws.

Controls

Power Button
Turn Heater ON/OFF by pressing the Power Button.
Timer Button
The timer can be set for up to 8 hours. Continue pressing the Timer Button to reach the desired time setting. Light turns red when activated.
Automatic Temperature Control
Press to Decrease the desired room temperature.
Oscillation Button
Press to Start/Stop the Base Oscillation function.
Heat Mode Button
Press to cycle between High and Low Heat.
Save-Smart® Button
Press to activate the Save-Smart® function
Automatic Temperature Control
Press to Increase the desired room temperature.

SAVE-SMART® FUNCTION

Set the thermostat to desired temperature using the ( ) and ( ) buttons (Note: The default Save-Smart® temperature is 72º F)
When you reach the temperature at which you want to set the unit, the set temperature will flash several times and then the display will return to indicate the current room temperature and will gradually change as the room temperature changes.
When the air temperature is less than the set temperature, the Heater will run in HIGH heat.
Once the thermostat reaches the set temperature the Heater will automatically switch to LOW heat to save energy.
When the air temperature reaches 4º above the set temperature, the Heater will turn off. The Heater will cycle off and on in the LOW mode to maintain the set temperature. All this happens automatically with Lasko Save-Smart®Technology. To deactivate the Save-Smart® function, press Save-Smart® again or ( ) for continuous high/low heat.

AUTOMATIC TEMPERATURE CONTROL

The automatic temperature function will only operate in high heat mode. You cannot set the temperature automatically when the unit is in Low heat mode.

1. To set the room at a specific temperature press the or buttons to the desired temperature. The display will now reflect the and the temperature will be flashing. The Heater is now in Auto Temperature Mode.
When you reach the temperature at which you want to set the unit, the set temperature will flash several times and then the display will return to indicate the current room temperature and will gradually change as the room temperature changes. NOTE: the temperature display does not indicate the temperature of the heated air being emitted by the Heater.
Once the room temperature reaches 2 degrees above the set temperature, the Heater will shut off. Once the room temperature reaches 1 degree below the set temperature, the Heater will turn back on and continue to cycle off and on to maintain the set temperature.
This function will cancel if the button is pressed. The Heater will now be in High heat and run continuously.

NOTE: It is normal for the Heater “fan” to run for approximately 15 seconds when the Heater shuts off after reaching the set temperature. Press the and buttons at the same time to change the display to ° Celsius. Press the same two buttons together again to change the display back to ° Fahrenheit.

SAFETY FEATURE

A thermal overload protector is built in to prevent overheating.
If an overheat temperature is reached, the Heater will automatically shut off. It can only resume operation when the user resets the unit.

To Reset Heater:

Unplug the Heater and wait 10 minutes for the Heater to cool down.
After the Heater has cooled down, plug the unit into a 120V~ electrical outlet and follow the operation instructions described in this manual.

TROUBLESHOOTING TIPS
If your Heater shuts off unexpectedly or fails to operate, the previously mentioned safety feature may have been activated to prevent overheating.

Be sure the power cord is plugged into a working electrical outlet.
Make certain the batteries in the remote control are new and properly installed.
Check your Temperature setting. The Heater may be off because it has reached the desired temperature setting.
If your Heater runs for several minutes and shuts off repeatedly, your Heater may require cleaning. See the Maintenance section below.
SERVICING: For servicing, other than general user maintenance, please contact Customer Service at 800-233-0268, Monday through Friday, from 8 am-5 pm Eastern. STORAGE: Store the Heater with these instructions in the original carton in a cool, dry place.
DISPOSITION: Corrugated packaging materials are recyclable. For environmentally responsible disposal of this product, contact your local waste service provider or visit www.1800recycling.com®.

MAINTENANCE

To reduce the risk of electrical shock and fire please observe the following instructions. Cleaning the Heater regularly will help to maintain its efficiency.

Always unplug the cord before moving, servicing or cleaning.
NEVER place the Heater in or near water. DO NOT IMMERSE THE HEATER IN WATER.
Clean the Heater only with a vacuum equipped with a brush attachment; the vacuum will remove the lint and dirt from the surface of the Heater.
Vacuum intake grills every two weeks; this will help to maintain the optimum Heater performance.
Use a toothbrush or other soft bristle brush to gently loosen any dirt not removed by the vacuum.
NEVER attempt to take apart the Heater.
Clean the body of the Heater with a soft cloth only.
NEVER use ALCOHOL or SOLVENTS such as gasoline, benzene, paint thinner, or other harsh cleaners.

LASKO PRODUCTS, LLC LIMITED WARRANTY (VALID IN THE USA, ITS TERRITORIES, AND CANADA ONLY)
WHAT THIS WARRANTY COVERS: This product is warranted against defects in workmanship and/or materials.
HOW LONG THIS WARRANTY LASTS: This warranty extends only to the original purchaser of the product and lasts for three (3) years from the date of original purchase or until the original purchaser of the product sells or transfers the product, whichever first occurs.
WHAT LASKO WILL DO: Lasko will, at its sole option, repair or replace any part or parts that prove to be defective or replace the whole product with the same or comparable model. For all warranty claims, the product must be returned to Lasko Products, LLC at customer expense with proof of purchase within the warranty period. Contact the Lasko customer service department to obtain a Return Authorization (“RA”). DO NOT return products without an RA or the warranty claim will not be processed.
WHAT THIS WARRANTY DOES NOT COVER: This warranty does not apply if the product was damaged or failed because of accident, improper handling or operation, shipping damage, abuse, misuse, unauthorized repairs made or attempted, or the use of the product for commercial or nonresidential service. This warranty does not cover shipping costs for the return of products to Lasko for repair or replacement. Lasko will pay return shipping charges from Lasko following warranty repairs or replacement. ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY), LAST THREE YEARS FROM THE DATE OF ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR TRANSFERS THE PRODUCT, WHICHEVER FIRST OCCURS AND IN NO EVENT SHALL LASKO’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY INCLUDE (I) INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER, OR (II) REPLACEMENT OR REPAIR OF ANY HOUSE FUSES, CIRCUIT BREAKERS OR RECEPTACLES. NOTWITHSTANDING ANYTHING TO THE CONTRARY, IN NO EVENT SHALL LASKO’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT AND ANY SUCH LIABILITY SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD. Some states and provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these exclusions or limitations may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state to state and province to province. Proof of purchase is required before a warranty claim will be accepted.

CUSTOMER SERVICE:
Toll-Free 800-233-0268. Email: producthelp@lasko.com
Our Customer Service team is available to assist you with product and service questions, and replacement parts. They can be reached Monday through Friday, 8 am-5 pm Eastern. Please have your model number available, as well as the type and style (located on the underside of your product). Customer Service Dept., 820 Lincoln Ave., West Chester, PA 19380
(Please do not send product to this location) www.lasko.com PARTS FOR DISCONTINUED, OBSOLETE AND CERTAIN OTHER PRODUCTS MAY NOT BE AVAILABLE. DUE TO SAFETY REASONS, MANY ELECTRONIC COMPONENTS AND MOST HEATER COMPONENTS ARE NOT AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT. Manual printed in China