INGENEXT Boost 50 Boost Sr & Bonus Module User Manual

: June 5, 2024
: INGENEXT

Table of Contents

INGENEXT Boost 50 Boost Sr & Bonus Module
CONNECTION
BATTERY PACK HEATING
WIFI AP CONTROL
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

INGENEXT Boost 50 Boost Sr & Bonus Module

CONNECTION

After installing the module in your car

Find the Ingenext WiFi access point on your smartphone, tablet or laptop. The name of the access point (AP) will be “Ingenext_xxxxxx”, with the last portion being the unique serial number for each module.
Log in with the following password: ingenext
On IOS devices, a captive screen will appear (the same type when you log into a hotel AP). Then click on the “Cancel” button and click on the “Use without Internet ” option at the bottom. You also need to make sure that you are not connected to a VPN. See figure 1
Open a new web browser page and type 192.168.0.1 in the address bar. A window will ask you to change the default AP password. You then need to choose a personal password with a combination of letters and numbers with at least 8 characters. See figure 2
After changing the password, you will be disconnected from the active WIFI AP connection from the module. You then need to reconnect to the WIFI AP with your new password and return to the web browser window. We recommend using the “Forget this network” option to make adding the new password easier. See figure 3
We also recommend that you deactivate the “Auto-join” wireless device. See figure 4

On some Android devices you might need to turn off the cellular data function in order to be able to access the Ingenext app web page.

BATTERY PACK HEATING

The battery pack heating function only works if the high voltage battery is below 30 °C.
To activate this function, the vehicle must be started with the driver seated in the driver’s position and the PRND selector showing on the user interface of the car (brake pedal depressed)
The passenger can also activate this function while the car is driving too.

DRIFT MODE
You can only activate it when the car is in Park. The drift mode deactivate all the following driving aids :

Automatic emergency braking
Regenerative braking
Stability control system.
Traction control system.

To activate the Drift Mode, you must first enable it in the Ingenext app. See figure 5. Then you must restart the car by going in the Safety & Security menu and click on the POWER OFF button. See figure 6
The center display in the car will go off. Wait 5 seconds and depress the brake pedal to restart the car. Once the car is restarted , the center display should show a telltale of a yellow car drifting and multiple alarm message related to the driving aids being turned off should be shown . See Figure 7 INGENEXT-Boost-50-Boost-Sr-&amp-Bonus-Module-4

WIPER MANUAL MODE

For the wipers manual mode to work, the wipers mode on the center display of the car need to be set in AUTO. See Figure
In the Ingenext app, the manual wiper control is always enabled once your module is installed : the long cycle (normal mode) is activated by default if the short cycle option button is OFF and the short cycle takes over if the option is ON.
You can then push the left stalk forward (same function to change the auto high-beam) and press the mist button once to switch between all mode. See Figure 9.

Each click goes through the following sequences:

NORMAL

Slow intermittent
Fast intermittent
Slow continuous
Fast continuous
Off
Auto

SHORT

Slow continous
Fast continous
Off
4 Auto

Then it cycle back to step 1

To turn off this function, you simply need to change the wiper mode in the center display to any other mode then auto.
The wiper manual mode also turn off automatically when you leave the car and your phone disappear from the vicinity of the car.

WIPER WINTER MODE

This option is meant to help you out deicing the wipers blades which can be cumbersome when they’re in their default Park position. If activated, the wipers will go in service mode by themselves when you’re going from Drive to Park if the ambient temperature is below the freezing point. You can get out of the service mode when you are in Park by just by taping the wipers mist button. INGENEXT-Boost-50-Boost-Sr-&amp-Bonus-Module-6

AUTOMATIC DRIVER DOOR (BETA)

You need to activate the Automatic Door Open setting in the Ingenext’s app. This function allows the driver’s door to open automatically when the driver approaches the car with his key fob or the phone key. See Figure 11
For this to work, the vehicle must be kept awake. For this, you need activate the sentry mode to keep the car awake and to allow it to monitor the presence of the phone key or the key fob. See Figure 12
The automatic door logic will only enable itself if the phone key or the key fob are far enough from the vehicle to not be detected for at least 15 seconds.
The open door proximity detection setting in the app can be set from closest to farthest depending on the strength of your Bluetooth signal. See Figure 11
We recommend that you test the settings for your car and your key fob/phone key. You should start by setting it to from the closest then to the farthest until you’re satisfied with how soon it open the door before you’re close to it.
Keep in mind that if you set it too far, it might trigger a false automatic door opening if you have , for example, your car in the garage and you’re close to it.
We also recommend that you activate the Lock Confirmation Sound in the Locks menu in the center display. This way, when the car unlocks the doors, the car will trigger a beeping sound to let you know that the door is open and unlock. See Figure 12

How the phone detection work for the auto door opening
In order to have auto door and auto trunk/frunk function to work, you need to set the detection and loss of sight threshold correctly for your use case. Figure 16 show how both the detection and loss of sight range works. The range between C and D is used to detect that the Phone-key is in range to trigger the auto-door opening an then allowing the auto trunk/frunk to work. The range between A and B is used to consider the Phone-key out of the range of detection and to trigger the 15 sec lockout timer to allow another detection of the Phone-key. Finally, the red portion of the spectrum is a dead-band range where no change of state can happen.

Phone loss of sight (100%)
Phone loss of sight (20%)
Driver’s door (farthest 100%)
Driver’s door (closest 100%)

AUTOMATIC FRUNK & TRUNK
You can choose the number of times and the duration that the frunk and trunk can be opened. These functions are accessible through the advance Automatic Doors menu. See Picture 10
For proper operation, you must have the Automatic Doors option enabled in order to wake up the proximity sensors when you’re approaching your vehicle. The Automatic frunk opening works with the side sensor closest to the driver’s side front wheel. See Picture 13 The Automatic trunk opening works with the side sensor closest to the driver’s side rear wheel. See Picture 14

Here are the steps to open the trunk/frunk

Position yourself approximately 24’’ from the sensor.
Then approach your leg to approximately 12’’
For the frunk: the left turn signal will flash for about 2-4 blinks. When it stop, you can move back to the 24” position you were at the beginning.
For the trunk: the left turn signal will flash rapidly. When it lit steady, you can move back to the 24” position you were at the beginning.
When you are back at the 24” position, the frunk or the trunk will open automatically. You can check this video:https://[www.youtube.com/watch?v=pJlrFwu2Ceg](https://www.youtube.com/watch?v=pJlrFwu2Ceg)

AUTOMATIC FRUNK & TRUNK

To get the full automatic opening experience, we recommend that you buy a set of shock absorbers for the Model 3 trunk and frunk like these: https://[amzn.to/2QLhr8k ](http://amzn.to/2QLhr8k)

INGENEXT-Boost-50-Boost-Sr-&amp-Bonus-Module-10

THE REAR HEATED SEATS

There’s two ways to control the Rear heated seats:
With the Ingenext’s app. See Picture 16With rear window switches. See Picture 17. You first need to activate the Heated Seats setting in the Ingenext app. Then, to turn on the rear heated seats, with the corresponding windows being in the roll up position, simply pull up briefly on the rear window switch. Each pull of the switch goes through the following sequence :
- Level 3
- Level 2
  Level 1
  Then it cycle back to Level 3
To turn off the heated seat, simply pull the windows switch up for at least 3 seconds.
When using the windows switches to control the rear heated seats level, the right seat also control the center seat setting since this one doesn’t have any switch
If you already have the factory installed option you will still be able to control the rear heated seats on your car center display as well as with the Ingenext app and with the rear windows switches.

INGENEXT-Boost-50-Boost-Sr-&amp-Bonus-Module-11 AMBIENT LIGHTS

The Ambient lights function will activate all the lights in the door’s pocket and at the feet of both the driver and passenger seat. See Picture 18.

NO TPMS ALERTS (BLE)

This option blocks the TPMS alerts on cars that have factory BLE TMPS sensors. See Picture 19

WIFI AP CONTROL

This function is used to turn on or off the Ingenext WIFI AP function.
While in Park, in the center display of the car, you need to first turn off the Windows Locked button. Then switch the center display WIFI interface from ON to the OFF position. See Picture 20 and 21
Then click on the Windows Locked button in the center display to turn it ON. Then wait approx. one second and then turn it OFF. Then wait one more second and click again on the Windows Locked button to turn it ON. Finally, wait one second and then turn it OFF again. See Picture 21.
Finally, turn the UI WIFI interface back to ON in the center display of the car, and put back the Windows Locked button to the state it was prior to this sequence.
4 YAoP ui nctearnf arceep beeatt wtehee n sOaNm oe r sOeFqF.uence to switch the WIFI

RESET WIFI AP PASSWORD

You should start this sequence with the center display WIFI interface on the ON position. See Picture 20
While in Park, cycle every second between the ON and OFF position
You should do this sequence (from ON to OFF) at least 4 times in order to reset the AP password to the default one : ingenext.

ALLOW UPDATES

In the future, all updates from Tesla on the center display will failed. In order to be able to allow these update to be installed, you must enable the Allow Updates setting in the Ingenext’s app.
Before installing any future update, we highly recommend that you visit our website
https://[ingenext.ca](http://ingenext.ca/pages/safe-tesla-updates-for- boost50-)/pages/safe-tesla-updates-for-boost50-and-bonus-module to confirm that the staged update on your center display is safe to be installed with your current Ingenext’s app version. If it isn’t , you should wait until a new version of the Ingenext’s app is released in order to fix potential changes and new features that would be deployed.
To prevent an accidental update of the center display, you should always disable the Allow Updates setting in the Ingenext’s app once the staged update is installed and the Ingenext’s app is updated accordingly.

HEATED STEERING WHEEL

This feature will activate the heated steering wheel if your steering wheel allows it. If your steering wheel is not designed to be heated, this feature will not work.
To activate it you must set the feature to on in the application and activate the heated driver’s seat.