gupup PST-WD301210 Smart WiFi LED Strip Lights Works with Alexa User Manual

gupup PST-WD301210 Smart WiFi LED Strip Lights Works with Alexa
User Manual

Product Overview

1. Built-in MEMS microphone, real-time acquisition of music, and environmental sound intensity
2. LED Strip Light sync to music, and contains a variety of musical rhythm modes
3. Infrared Remote Controller Control(Optional)
4. Press the key to switch mode and color
5. Control by SmartLife APP
6. Works with Amazon Alexa and Google home and so on

Product Parameter

WIFI Controller Box

IR Remote Controller

How to install

1. Prepare all the required accessories before you begin the installation.

2. Peel off the adhesive strip from the backside of the LED STRIP

3. Stick the LED STRIP LIGHTS on an even surface.

4. Connect the pins of LED STRIP LIGHTS into the socket of the control box ( both arrows pointing at each other). Beware of the polarity and direction of the pins of LED STRIP LIGHTS and the socket of the control box. LED would not light up if it is not connected with the correct polarity and direction.
   Note: Connect the LED strip pins socket and the LED strip pins, where both arrows are pointing at each other

5. The sensor of the Infrared (IR) receiver must be placed at the visible range and should be less than 5M from the remote control. The round face of the IR sensor should be faced with remote control without obstacles.

6. Connect the DC plug of the USB cable into the DC socket of the Control Box.

7. Connect the USB 2.0 Plug of the USB cable into the USB socket of your TV or USB outlet of the AC adapter (not included)

Batteries Installation for Remote control
A button cell battery (CR2025) is installed in the remote control.
Pull out the PVC plate from the battery door for contact with the battery before use.

To replace/ install a new battery into the remote control:
If the remote control is not operating properly or not responding at all the battery may be exhausted. Follow the below instruction to replace a new battery. Open the battery door and follow the instruction diagram on the backside of the remote control. Insert 1x button cell battery (CR2025). The battery should be placed as shown on the diagram below.

Software Manual

Download and Install App
Use your phone to scan the QR code below or search “Smart Life” in the application marker to Download and install the App

https://e.tuya.com/smartlife

Register/Login/Forget password
Register: Register your account to the following tips before using it for the first time.lf you have an account, please enter the password to log in directly.
Login: input the correct account number and password to log in.
Forget your password: You can enter the login page to retrieve your password.

Add Device-Normal mode
In the main application page, click on the top right corner “+” to the next window page and then choose Lighting, as shown below.
In normal mode, please confirm that the device’s red light is quickly blinking and then into the next step.
Note:
If the light is not flashing, press the “mode” key of the controller for 5-10 seconds to keep the red light in the quick blink for searching & connecting the network.
If adding the device in Normal mode fails many times, please go to Add Device- AP mode

Add Device-AP mode

In the main application page, click on the top right corner “+” to the next window page and then choose Lighting,as shown below.
In normal mode, click on the top right corner “AP Mode” to the AP Mode window page.
In AP Mode, please confirm that the device’s red light is slowly blinking and then into the next step.
Note:
If the light in quickly blinks, just press the controller for 5-10 seconds again, and the red light will slowly blink.
If the light neither slowly blinks nor quickly blinks. First press the “mode” key of the controller for 5-10 seconds to keep the red light in the quick blink, Second release the button and then press the controller for 5-10 seconds again,the red light will slowly blink. 

Control device

After successfully connecting the devices, the related smart device will be shown on the home page.Tap to enter its control page
Note:

1. when the device is online, it supports quick operations
2. when the device is offline, it displays “Offline”.and can not be controlled.
   

LED Strip Light Sync to Music Function
Enter music mode and play music with any device, and the led strip light will sync to music
Note:
The volume of mobile phone is relatively small, so it’s better to use Bluetooth audio

1. Click Edit in the top right corner to enter a custom scene
2. Breath and Static music mode is suitable for light music
3. Flash music mode is suitable for fast rhythm music
4. You can add/delete/modify the color displayed and change the speed of color switching
5. If you are not satisfied, you can reset the settings
   

Works with Amazon Alexa

Works with Google Assistant

FAQ

1. How to reset the controller?
   Press the ‘mode key of the controller for 5-10 seconds

2. How to get more help?
   

Attentions

1. Please use the product in a dry environment.
2. Please use the input voltage at 4.5-25V DC voltage, must not connect to 220V AC directly.
3. The product is requested a common anode connection. The wrong connection will cause a malfunction.
4. In the process of the product and software upgrade, the data and software interface listed in the text are only for description and reference.No further notification will be given if there is any change.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>