eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone App User Manual

June 3, 2024
eMACROS

eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone App

eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone
App

Overview

Sensor

eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone App
1

Base Station

Powering and Pairing Sensor and Receiver

Base Station

  1. Plug the Base Station into an outlet using the AC adapter. Base Station can also run on (4)AA batteries for up to 2 weeks, as backup in case of power outage.

  2. The red power light will illuminate on #3 when the Base Station is on. To turn the Base Station on /off, hold down the power button until you hear the on/off tone.

  3. Adjust the Base Station volume as needed, using the adjustable Volume+/- buttons. Volume adjustments will be heard on subsequent alarm activations, not while adjustments are being made. Powering off the base station will reset the volume to the factory setting.eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone App 3

  4. Before installing the PIR Sensor, recharge the sensor (with 18650 battery attached) using the AC adapter to ensure a full charge. The blue light will illuminate while charging. The blue light will turn off once the battery is fully charged.
    Note : The sensor hos been tested several times in the factory. If the blue light wont illuminate, the battery may be fully charged, you can install it directly.

  5. High/ Low/ Off Switch: First, open the black silicone seal cap at the bottom of the PIR Motion Sensor, then turn on the sensor by switching to High or Low. Set the detection range to High (30feet), Low (20 feet), or turn sensor Off.

  6. CH 1-4 Switch: Select a different channel for each outside sensor. When detecting movements, a sensor eye will flash red only when assigned to lines 1 and 2, not lines 3 or 4.
    Note : Each Separate channel uses an unique chime, allowing you to match different chimes with different channels.

  7. Test the PIR Motion Sensor by waving your hand in front of the sensor. The Base Station will produce a unique tone based upon the sensor’s setting.

eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone App
4

INSTALLING THE SENSOR:

  1. Mount the waterproof PIR Motion Sensor vertically on a solid surface 3-5 feet (1-l.5m) above the ground (rotate sensor to access screw holes). The sensor should be able to swivel as needed. Position the sensor to avoid direct sunlight shining on the sensor eye while simultaneously keeping the solar cell facing upward.

  2. Vehicle Alert Installation: The best mounting position for detecting vehicles is about 4 feet (1.2ml high. The PIR sensor detects the movements with heat sources; please adjust the sensor eye with horizontal angle to the engine of the car.
    Note : The sensors operate best in the -4F to 140F degree range. The sensors will not work properly outside of this temperature range.

    • The PIR Motion Sensor operates, but the base station does not respond.  Check the sensor switch settings (Refer to Instruction Manual – Assembly & Setup) .

A letter from eMACROS

Dear customers,
Thank you for choosing eMacros, we provide lifetime warranty and technical support for our customers. If you have any problems, please contact us by navigating to: www.emacros.com, then click Contact Us, we will assist you as soon as possible.

You can also email us:

Are you happy with our product?
Please text: Hi eMacros, I like it, my order number is * to our email: macross.service@outlook.com** or contact us via Facebook page: @emacross, you will enjoy our VIP treatment.

  • Free trial on our new products

  • VIP only coupon an promotions

  • Free birthday gift for VIP

  • Not happy?
    Please contact us if you have any concerns about the product, prior to leaving any online feedback, so that we may address your concern as quickly as possible. Our customer service support will work hard to put a smile back in your face.

  • Resend one new replacement

  • 100% full refund

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

1/2 Mile Solar Driveway Alarm

Note: BT274A is the receiving part of BT274 and BT274B is the transimitting part of BT274.
Thank you for choosing us, we provide lifetime warranty and technical support, if you have any problems, please email us at

Features

eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone App
7

Base Station Functional Description

Power
Press the Power button once to turn on the base station, the red power indicator LED will light up. Press and hold the Power button for 3S to turn off the base station.

1 / Mode(How to change the channel/tone)

Step 1. Press and hold the Mode button for 3S enter the pairing mode.
Step 2. Press the Mode button once to select the channel number during paring mode.

VOL+/VOL-
Press the VOL+ button to increase the volume level of based station.
Press the VOL- button to decrease the volume level of based station.

Channel Indicators
When motion is detected the corresponding channel please charge”.

Law Battery prompt

  1. When the battery level of Solar Driveway Alarm is low, the base station will prompt the “channel 1 or channel 2/3/4/5/6/7 power low,
  2. When the battery of base station is low, the red power LED will flash and prompt “base power low”. Nate:
  3. We recommend using the AC adapter to provide the power supply to Base station and the 4 AA batteries as backup in case of power outage for about 2 weeks.
  4. classic melodies optional.

Switch different channels to get a different ringtone

  1. First, unplugging the power cord or remove a battery from the receiver.

  2. Plugging in the receiver while long pressing POWER, you will hear 3 beeps, all memory is cleared.

  3. Holding the “mode” button until a number selection flashes.
    4

  4. Single pressing the mode button to the desired chime and then activate a sensor to “set” the chime to that device.

eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone App
8 eMACROS HS002 Pro 2 Smart
Wireless Driveway Alarm with Phone App 9

Solar Driveway Sensor eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm
with Phone App 10

PIR MOTION SENSOR INSTALLATION:
Mount PIR Motion Sensor horizontally on solid surface 5-6 feet (1.5-2m) off the ground and within 1/2 mile of Base Station (rotate sensor to access screw holes). Unit should be able to swivel as needed.
Note : Keep PIR Motion Sensor away from metal objects. Do not mount PIR Motion Sensor in direct sunlight, near moving tree branches, or in the path of a sprinkler system.

Vehicle Alert Installation: For cars, the best mounting position is about 5-6 feet (1.5-2m) high and making the sensor whitin 30 feet from car or people.

eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone App
12

Troubleshooting

  1. The base station does not work
    Check the AC Adapter of base station if it is ok. Check the Battery might be low and replace it.

  2. Short operating range
    There might be too many objects between the Base station and the Solar Motion Sensor. Try relocating objects or change the location of the Based station and Sensor. Check the Battery might be low charge it or contact us to replace with a new sensor.

  3. The system is giving false alarms
    Check for moving tree branches or insects in the sensor window and remove as necessary. Ensure that sunlight is not shining directly onto the sensor eye.

Technical parameters

  • Wireless Frequency : 433.92MHz FSK
  • Wireless Transmission Range
  • Driveway Alarm: 1/2Mile
  • Driveway Alarm detection Range: 30FT (9M) Driveway Alarm detection Anl : 120°
  • Base Station : 4*1.SV AA Batteries Solar Driveway Alarm : 3.7V/2200mAh
    • Working Temperature Range
      – 20°C –60°C (-4°F –140°F)

Overview

eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone App
13

Powering and Pairing Sensor and Receiver

Base Station

  1. Plug the Base Station into an outlet using the AC adapter. Receiver can also run on batteries as backup in case of power outage for 2 weeks.
  2. To turn the Base Station on or off, hold down the Power button until you hear the on/off tone.
  3. Adjust the Base Station volume as needed, volume adjustments will be heard on subsequent alarm activations, not while adjustments are being made. Powering off the bases station will reset the volume to the factory setting.

Sensor

  • Plug the small battery wire into the connector. Align notches to plug. (Red + /Black -)

  • Before mounting the PIR sensor, recharge the sensor using the AC adapter to ensure a full charge. The blue light will illuminate while charging. The blue light will turn off once the battery is fully charged.
    Note : The sensor has been tested several times in the factory. If the blue light won’t illuminate, the battery may be fully charged, you can install it directly.

  • Test the PIR Motion Sensor by waving your hand in front of the sensor. The Base Station will produce a unique tone based upon the sensors channel settng. When detecting movements, a sensor will flash red only when assigned to lines 1 and 2, not lines 3 or 4.
    Note : Each separate channel uses an unique chime, allowing you to match different chimes with different channels.

eMACROS HS002 Pro 2 Smart Wireless Driveway Alarm with Phone App
15

Installing the Sensor

  • Mount the PIR Motion Sensor vertically 4.5-6 feet (1.5-2m) above the ground on a solid surface (i.e. a wall, wooden post or tree) with the sensor eye pointed straight out over the area you wish to cover. (rotate sensor to access screw holes). The sensor should be able to swivel as needed.
  • Vehicle Alert Installation: The best mounting position is about 4.5-6 feet (1.5-2m) high. The PIR sensor detects the movements with heat sources; please adjust the sensor eye with a horizontal angle to the engine of the car.

Troubleshooting:

The PIR Motion Sensor operates, but the base station does not respond. Check the sensor switch settngs (Assembly & Settng) and make sure the battery wire is securely plugged into the connector.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals