ring 5B28S5 Contact Sensor Instruction Manual
- June 5, 2024
- Ring
Table of Contents
ring 5B28S5 Contact Sensor
Placement
Slim Magnet
First, complete the in-app setup.
- Make sure your Ring Alarm is disarmed.
- In the Ring app, tap Set Up a Device and find the Contact Sensor in the Security menu.
- Follow the in-app instructions to complete setup.
Then, install the device in your home.
- Choose the door or window where you’d like to install your Sensor and magnet.
- If the magnet is too large, open the back and remove the magnet piece from the magnet case and mount it directly.
- Line up the Sensor and magnet, with no more than 2.5cm (1”) between them.
- Leave at least 1.3cm (1/2”) space around the Sensor so you can open the battery compartment.
- Clean the area, then peel the backing from the mounting tape and press the Sensor and magnet into place.
- To install using screws you will need: Screws: 4x 3x21mm. Anchors: 4x 5mm.
If you’re using the Contact Sensor on a door you use often, choose Main Door as the placement option. Main doors have Entry and Exit Delays to prevent you from accidentally triggering the alarm.
How to change the battery.
Slide the sensor backward and off the mounting bracket. Replace the battery
with fresh CR2032 cell batteries. Ensure that the battery is inserted
correctly. When inserting batteries, make sure the (+) is facing up.
WARNING: Inserting the battery with the wrong polarity may damage the
device.
SAFETY AND COMPLIANCE INFORMATION
Use Responsibly. Read all instructions and safety information before use.
SAFETY INFORMATION
WARNING! Failure to read and follow these safety instructions before the
operation could result in fire, electric shock, or other injury or damage.
WARNING! Your device should only be used in accordance with the specific
instructions for use and the intended purpose of the device. Using your device
in any way other than its intended purpose could cause injury to yourself,
others and/or damage to the device or property.
CAUTION! The device is not waterproof and as such should not be submerged
in water, doing so could cause injury to yourself, and others and/or damage to
the device.
WATCH FOR SMALL PARTS! Your device and accessories may present a choking
hazard to small children. Keep them out of reach of small children.
Ring Contact Sensor is for indoor use only.
BATTERY SAFETY
This product contains lithium coin batteries. This device requires batteries
for use. Only use new CR2032 3V batteries. Never mix old and new batteries.
Keep all of the batteries out of the reach of children. Do not open,
disassemble, puncture, cut, bend, shred or heat the batteries and do not allow
metal objects to touch the battery terminals on the device as they can become
hot and cause burns. Remove all batteries if they are worn out or before
storing your Device for an extended period of time.
Dispose of all batteries in accordance with applicable laws and regulations
and do not dispose of batteries by throwing them into a fire. If any batteries
begin to leak, take steps to prevent the fluid from coming into direct contact
with skin or clothes as the fluid could be corrosive and may be toxic. Remove
the batteries and clean the battery compartment in accordance with the battery
manufacturer’s recommendations.
CAUTION! The danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of the used batteries according to the manufacturer’s instructions.
CHEMICAL BURN HAZARD! This product contains lithium coin batteries. Do
not ingest batteries. If the coin cell battery is swallowed, it can cause
severe internal burns in just 2 hours and lead to death. Keep all of the
batteries out of the reach of children. If you think batteries might have been
swallowed or placed inside any part of the body, seek immediate medical
attention.
PRODUCT SPECIFICATIONS
- Model Number: 5B28S5
- Electrical Rating: 2x CR2032 3V
- Temperature Rating: 0°C – 49°C
DECLARATION OF CONFORMITY
Hereby, Ring LLC, declares that the radio equipment type Ring Contact Sensor
(5B28S5) is in compliance with Directive 2014/53/EU and relevant UK statutory
requirements. The full text of the Declarations of Conformity are available at
the following internet address: ring.com/doc.pdf.
RADIOFREQUENCY COMPLIANCE
In order to protect human health, this device meets the thresholds for
exposure of the general public to electromagnetic fields according to Council
Recommendation 1999/519/EC. This device should be installed and operated with
at least 20 cm between the radiator and your body.
- Wireless Features: Z-Wave
- Maximum Equivalent Isotropically Radiated
- Power: 868.40 – 869.85 MHz 4.38 dBm EIRP
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make
sure you dispose of, or recycle, your device in accordance with your local
laws and regulations.
MANUALS
Find online manuals at: ring.com/alarm-manual
WARRANTY
Find warranty information at: ring.com/warranty
Z-WAVE
For Z-Wave technical information, visit: ring.com/z-wave
- UK +44 1727 26 3045
- EU +800 8700 9781
- Saudi Arabia +80081 47867
- UAE +80001 84084
- South Africa +0800993700
- Worldwide +1 310 929 7085
Ring
Singel 542 1017 AZ Amsterdam The Netherlands 1 Principal Place, Worship Street
London, EC2A 2FA United Kingdom 2021 Ring LLC or its affiliates. Ring and all
related marks are trademarks of Ring LLC or its affiliates.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>