SEBSON HF_ES_A Indoor Flush Mount Motion Detector User Guide

June 15, 2024
SEBSON

SEBSON HF_ES_A Indoor Flush Mount Motion Detector

Product Information

Specifications

  • Bewegungsmelder Model: HF_ES_A
  • Lieferumfang: 1 Bewegungsmelder
  • Betriebsspannung: 220-240V AC 50/60Hz
  • Maximale Leistungsaufnahme : Max. 1.200W
  • Maximale Leistungsaufnahme im Standby : Max. 300W
  • Schutzart : IP20 II
  • Frequenz : 5,8GHz CW

Product Usage Instructions

Safety Instructions

  • Function of the Bewegungsmelder:
    The Bewegungsmelder is a motion detector that detects movement within its range and triggers a response.

Installation Instructions

  1. Before installing the Bewegungsmelder, carefully read and follow all safety instructions and technical specifications provided.
  2. Select a suitable location for installation. Ensure that the Bewegungsmelder has a clear view of the area to be monitored.
  3. Mount the Bewegungsmelder securely using the recommended mounting method shown in Abb.1b.
  4. Connect the protective earth (PE) wire according to the local electrical regulations.
  5. Adjust the detection range  using the provided switch (see Abb.3b).
  6. Perform a function test to ensure proper operation.

Operating Instructions
The Bewegungsmelder has an adjustable operating time duration. The duration can be set from approximately 10 seconds to 12  minutes. The timer will restart if motion is detected bythe sensor before the set time expires. The can be adjusted to control the sensitivity of the Bewegungsmelder to ambient light conditions.

FAQ

  1. Q: What is the maximum power consumption of the Bewegungsmelder?
    A: The maximum power consumption of the Bewegungsmelder is 1,200W during operation and 300W in standby mode.

  2. Q: What is the frequency of the Bewegungsmelder?
    A: The Bewegungsmelder operates at a frequency of 5.8GHz CW.

Manual

  • Thank you for choosing a product of SEBSON. Please read the instructions carefully and keep them for looking up before start-up this product. A long and failure-free operation can only be guaranteed if the installation and start-up is done properly. Before starting up this product, please check for external damage. In case of visible external damage we immediately dis-advise the start-up of this product! Please remove all packaging material of this product before the first start-up an and check the content for completeness!

Intended use:

  • This active motion detector generates high-frequency electromagnetic waves (5.8 GHz) and receives their echo after hitting moving objects, regardless of their temperature. This signal is then sent to a connected light, for example, which then switches itself on.

Scope of delivery

  • 1 motion detector

General safety information

  • Danger: The installation of this product may be done only by a qualified person according the valid regulations for electrical installation!
  • Danger: If the power cables are damaged or come into contact with wetness, immediately disconnect the product from the power supply and ensure that it cannot be switched on again!
  • Danger of suffocation: Please keep this product away from children and animals. The packaging contains small parts that can be swallowed!

Caution : Avoid overloading the device, an overload can damage the device or cause a short circuit! Therefore, please note the maximum power consumption in the technical data!

  • The remodeling of this product is not allowed! The proper and safe functioning of the device can no longer be guaranteed if it is modified! In addition, this will invalidate the warranty claim!
  • The manufacture does not accept any responsibility for injuries or damage resulting from improper use of this product!
  • Any other use than the description may result in damage to the product. So the dangers are such as electric shock, short circuit, fire etc.
  • We reserve the right to make changes to the product, the packaging or the operating instructions as well as printing errors.
  • This product is only suited for indoor-use and not for outdoor-use!
  • Protect the product from external damage, heavy dirt, moisture and excessive heat!
  • In order that the warranty claim does not expire please use only the supplied items. Repairs may only be done by an expert and only by using original spare parts!
  • In commercial institutions, the accident prevention regulations of the professional trade association for electrical equipment and facilities must be adhered to.

Instruction for installation (Fig 4)

  • Danger: Before installing please make sure that the circuit is interrupted! For installation, the work on the mains voltage is required. Please remove the associated mains fuse or deactivate the switch fuse! Check by using a voltage tester if the line is de-energized. Make sure that the current circuit will not closed during the installation!
  • Danger: The installation of this product may be done only by a qualified person according the valid regulations for electrical installation!

Attention: Before drilling the mounting holes, make sure that there are no gas, electricity or water pipes at the drilling location that could be damaged by this!

  • Please observe the safety instructions and technical data before installing this product!
  • Note on installation:
    • L: Live wire (black or brown)
    • N: Neutral conductor (blue or grey)
  • This device is only suitable for ceiling mounting!
  • When mounting the unit on the ceiling, mount it at least 1m away from the wall. If the wall is very thin, a greater distance is recommended. The sensor could also detect movements behind this wall.
  • Observe a minimum distance of 2 meters when commissioning several motion detectors.
  • For optimum range, select the mounting height recommended in the “Technical Data”.
  • 2 units in a parallel connection (see Fig.3a)
  • Permanent switch-on of a connected unit with an additional switch connected in parallel (see Fig.3b).

The following environments or surfaces are not suitable for mounting, as they can impair the function of the motion sensor:

  • Metal surfaces, for example metal door frames or metal-coated walls
  • Metal contained in masonry e.g. steel girders
  • In the immediate vicinity of electronic devices such as computers, monitors etc
  • Water drainage or supply pipes can trigger a signal when water flows

Function of the motion sensor

  • This product is an active motion detector. It generates high-frequency electromagnetic waves (5.8GHz) and then receives their echo. The motion detector thus reacts to changes in the waves reflected back from objects,  regardless of temperature. As a result, the smallest movements that occur in the detection range of the product can be detected. The integrated microprocessor triggers the command “Switch on light” almost without delay. This enables the perception of movements through doors, glass panes or thin walls. Note: The radiation emitted by the sensor has a power of about 0.2mW. Thus the power of the radiation is about 1/ 5,000th of that of a mobile phone. The product can therefore be used without any risk.

  • Detection area (Fig 2):
    The detection range of the motion detector is approx. 2-16m and 360° (free area) at a mounting height of 1,5-3,5m at the ceiling. In closed rooms the detection distance can be lower, according to room layout.

  • Connection of the protective conductor (PE): When connecting a lamp with protective conductor contact, the protective conductor must be bypassed from the supply line to the lamp with the aid of an additional terminal in the in-wall socket.

  • Sensitivity when switching (with regard to the ambient brightness): This setting control can be used to regulate the switch-on sensitivity of this unit depending on the ambient brightness (between 3 and 2.000LUX).

  • Time setting (switching off delay): The duration of the operating time can be set continuously from approx. 10s to 12min. The timer is restarted if a movement from the sensor is detected before the set time has elapsed.

  • Reach Setting: With this setting controller, the detection range of approx. 2m to 16m can be set. Turning the adjuster to the left will extend the range.

  • Function test:

To set the detection range and the daylight test, turn the knobs to the positions shown. The motion detector is activated after a warm-up phase of approx. 30s. If no further movement takes place in the sensing area of the sensor, the sensor switches off.

Installation recommendation (Fig 1b):

Mounting hole:| Ø 63-66mm
Maximum thickness of mounting surface:| ≤40mm
Mounting depth:| ≥60mm
Technical Data:

Operating voltage:| 220 -240V AC 50/60Hz
Maximum power consumption:| Max. 1.200W     Max. 300W
Electrical protection:| IP20
Protection class:| II
Frequency:| 5,8GHz CW
Transmission power:| <0,2mW
Detection moving speed:| 0,6-1,5m/s
Ambient temperature:| -20° – +40°C
Humidity:| <93%
Possibilities of adjustments:

Detection area:| 2-16m/ 360°
Sensitivity when switching (with regard to the ambient brightness):| <3-2.000LUX
Time setting (switching off delay):| Min. 10s +/- 3s – Max. 12min +/-1min

Information for private households (WEEE)

  • The Electrical and Electronic Equipment Act (WEEE) contains a large number of requirements for the handling of electrical and electronic equipment. The most important ones are summarised here.
  1. Separate collection of waste equipment
    Old, worn-out or defective electrical and electronic equipment is referred to as waste equipment. These devices must not be disposed of in the normal household waste or together with the residual waste. The devices should be transferred to special collection and return systems.

  2. Batteries and rechargeable batteries as well as illuminants

    • As a rule, owners of WEEE shall separate spent batteries and accumulators that are not enclosed in the WEEE, as well as light sources that can be removed from the WEEE without causing damage, from the WEEE before handing it over to a collection point. This does not apply if WEEE is prepared for reuse with the participation of a public waste management authority.
    • Batteries or rechargeable batteries that contain harmful substances are marked with the symbol of a crossed-out dustbin and must not be disposed of in household waste. Below the dustbin symbol is the chemical name of the pollutant – in the example below “Cd” for cadmium. “Pb” stands for lead, “Hg” for mercury:
      If disposed of improperly, the substances contained in the batteries may cause hazards to health and the environment. The hazards are averted by the separate collection and proper disposal of used batteries.
  3. Options for returning old appliances
    Owners of WEEE from private households can hand it in free of charge at the collection points of the public waste management authorities or at the take- back points set up by manufacturers or distributors.

  4. Data privacy notice
    Old devices often contain sensitive personal data. This applies in particular to information and telecommunications technology devices such as computers and smartphones. In your own interest, please note that each end user is responsible for deleting the data on the end-of-life devices to be disposed of.

  5. Meaning of the “crossed-out dustbin” symbol
    The symbol of a crossed-out dustbin regularly displayed on electrical and electronic equipment indicates that the respective device must be collected separately from unsorted municipal waste at the end of its service life.

Cleaning

  • Danger: Before start cleaning the product interrupt the current circuit by switching off the circuit breaker or unscrew the fuse! Use a slightly moistened cloth for cleaning. In order not to damage the product, it is essential to avoid water penetrating into the housing! Never clean the device under running water! Do not use solvent-containing cleaner for cleaning.
  • Address:
    • SEBSON
    • Sebastian Sonntag Walter-Behrendtstr.10 44329 Dortmund Germany
  • support@sebson.de
    • VAT-Nr.: GB179436663
    • WEEE-Reg.-ID.: 500617

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals