TOPDON JUMPSURGE1200 Jump Starter for 12 Volt Lead-Acid Batteries User Manual

TOPDON JUMPSURGE1200 Jump Starter for 12 Volt Lead-Acid Batteries

GENTLE REMINDER

To be environmentally friendly and consider other factors, our paper manuals are only in English, German and Japanese. For other languages, please visit our official website https://www.topdon.com/, go to the corresponding product page and click “DOWNLOADS” to download the online user manuals, or scan the QR code to visit our website and obtain online user manuals.

WARNING
To ensure your safety, please read carefully and understand thoroughly all safety instructions before using this product. Go to www.topdon.com for more information.

PRODUCT OVERVIEW

A GUIDE T0 SAFETY INDICATOR

• Solid green The Jump Starter is ready for use.
• Solid red Reverse polarity of battery clamps is detected.
• Flash green The battery level of the vehicle is too low.
• Press the “BOOST” Button and wait until the Safety Indicator becomes solid green. Then start your vehicle within 30 seconds.
• The indicator doesn’t light up The battery of the vehicle may be totally dead. Make sure that you have correctly connected the clamps to the vehicle battery. Then press the “BOOST” Button and wait until the Safety Indicator
• becomes solid green. And then start your vehicle within 30 seconds.
• Alternately Flash Red and Green You have tried 4 jump starts within 10 minutes. Please disconnect the clamps and reconnect to try again.

A GUIDE TO LED LIGHT

1.  Press the Power Button once to turn on the jump starter.
2. Press and hold the Power Button for 3 seconds to turn on the LED Light. Then press the Power Button once separately to toggle between Flashlight, Strobe, SOS and OFF in turn

RECHARGE THE JUMP STARTER

The jump starter comes partially charged and needs to be fully charged prior to use. Please charge it through the Type-C Input port once you receive it.

NOTE: Please jump start vehicles only when the battery level of the jump starter is more than 50%.

JUMP START VEHICLES (12IONLY]

IMPORTANT: Make sure you have turned off all of the power loads of the vehicle, including headlights, radio, air conditioner, etc., before attempting to jump start the vehicle.
Plug the blue end of jumper cable into the Jump Start Socket.

Connect the clamps to the vehicle battery. Red clamp to positive polarity(+), black clamp to negative polarity(-). The Safety Indicator will be solid green which indicates it is ready for jump starting.

NOTE: Please check the connection if the Safety Indicator is abnormal or the buzzer rings.

Try to start the vehicle. If it fails, disconnect the clamps from the vehicle battery and wait about 20 seconds, then reconnect and try again. Do not attempt more than 3 consecutive jump starts within 2 minutes

Remove the clamps from batteries, then separate the jumper cable and jump starter after cranking the vehicle successfully. Your jump starter will automatically power off in several seconds

TECHNICAL SPECIFICATION

• Model JUMPSURGE1200/JUMPSURGE2000
• Peak Current 1200A(JUMPSURGE1200); 2000A(JUMPSURGE2000
• Battery capacity 10000mAh, 3.7V/37Wh(JUMPSURGE1200); 16000mAh, 3.7V/59.2Wh(JUMPSURGE2000)
• Output USB1 QC18W, 5V/9V/12V; USB2 5V 2A; DC Max 16.8V 10A
• Input Type-C 5V 3A, 9V 2A
• WorkingTemperature -10°C~40°C(14°F~104°F)
• Storage Temperature -20°C~75°C(-4°F~167°F)

References

• TOPDON|Automotive Diagnostic Tools, Battery Tools and Key Programmers
• TOPDON|Automotive Diagnostic Tools, Battery Tools and Key Programmers – TOPDON TECHNOLOGY Co., Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>