amazon basics C1hN1XDDC6L Grade 3 Electronic Door Lock User Manual

Amazon Basics C1hN1XDDC6L Grade 3 Electronic Door Lock

Important Safeguards

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.

• Prevent unauthorized entry. The electronic lock is pre-programmed with default user code and programming code. After installation and setup, change the codes. Store the codes in a safe place and change them from time to time.
• Make sure that no unauthorized person has access to the codes.
• Do not use excessive force or sharp objects to push the buttons on the keypad.
• Close the door completely when going outside. The manufacturer does not assume responsibility for any harm caused by the engagement of the lock on an improperly closed door.
• No lock can provide complete security by itself. This product may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. The builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, consult a qualified locksmith or other security professionals.

Before First Use

• Remove all the packing materials.
• Remove and review all components before use.
• Check the product for transport damages.

Operation

Inserting batteries
NOTICE

• Always use alkaline batteries. Insert batteries correctly with regard to polarity(+ and -l marked on the battery and the product.
• Exhausted batteries should be immediately removed from product and properly disposed. Replace all batteries at the same time. Do not mix new and old batteries.
• Insert the batteries after the product has been installed on the door.
• The programming code and user code will be stored after replacing batteries.

1. Push the battery compartment cover (Ml upwards, then pull it out.
2. Insert four AA batteries into the battery compartment.
3. Slide the battery compartment cover (Ml back onto the interior assembly (Kl.

Indicator signals

Programming

NOTICE

• Programming and assigning new codes is only possible when the lock is unlocked and the door is open.
• In this chapter, PC refers to programming code; and UC refers to user code.

Determining Door Handing

NOTICE: Before use, follow the below combination to teach the lock the orientation of the door. The default programming code (PC) is 0000.

Do this first
The latch bolt will extend and retract. Once the operation is successful, the lock emits two long beeps.

Changing Programming Code

NOTICE

• The default programming code (PC) is 0000. Change the code to 4-10 digits in length.
• The programming code and user code cannot be identical.
• The lock will temporarily freeze for 45 seconds if an unauthorized codes code has been entered more than 5 times.

NOTICE

• The default user code (UC) is 1234. Change the code to 4-10 digits in length. Up to 30 sets of user codes can be saved.
• The programming code and user code cannot be identical.
• The lock will temporarily freeze for 45 seconds if an unauthorized codes code has been entered more than 5 times.

Deleting an Existing User Code

Deleting All User Codes at Once

NOTICE: When all user codes are deleted, the lock can only be operated with the keys. Auto-lock or keypad functions are disabled until a new user code is set.

Activating/Deactivating Auto-Lock

NOTICE: After the auto-lock function is activated, the lock locks automatically after being unlocked for 30 seconds.

Setting Auto-Lock Time Delay

NOTICE: The default auto-lock time delay is set to 30 seconds. Set the time delay between 10 and 99 seconds.

Enabling/Disabling All User Codes

NOTICE: When all user codes are disabled, the lock can only be operated with the keys. Auto-lock or keypad functions are disabled.

Creating a One-Time User Code

NOTICE: The one-time user code can only be used once and will expire automatically.

Using the electronic lock
To lock the door, touch the touchpad and press the key. Alternatively, the lock locks automatically if the auto-lock function is activated.

To unlock the door:

1. Touch the touchpad and a series of random keys light up.
2. Press all the random keys, then all keys light up again.
3. Enter the user code and press the key.

The random codes can be activated/deactivated by the following process :

Restoring Default Settings

NOTICE: Using a pointed object, press and hold the reset button for 5 seconds. The lock emits 3 long beeps and all the settings are restored to the original factory settings. Follow steps in chapter “Determining Door Handing” before re­programming.

**Cleaning and Maintenance

**

• To clean the product, wipe with a soft, slightly moist cloth.
• Regularly check that all the components and fasteners are tightened.
• Never use corrosive detergents, wire brushes, abrasive scourers, or metal or sharp utensils to clean the product.

Troubleshooting

FCC – Supplier’s Declaration of Conformity

Unique Identifier

• B08J4MPXH2:  Grade 3 Electronic Touchscreen Deadbolt Door Lock with Door Handleset Satin Nickel
• B08J4K95KV:  Grade 3 Electronic Touchscreen Deadbolt Door Lock with Door Handleset Matte Black
• B08J4KCCHZ:  Grade 3 Electronic Touchscreen Deadbolt Door Lock

Satin Nickel

• B08J4LRCH6: Grade 3 Electronic Touchscreen Deadbolt Door Lock Oil Rubbed Bronze
• B08J4K7XSC: Grade 3 Electronic Touchscreen Deadbolt Door Lock

Matte Black

• B08J4MPXHJ: Grade 3 Electronic Touchscreen Deadbolt Door Lock with Passage Lever Satin Nickel
• B08J4M6LJS: Grade 3 Electronic Touchscreen Deadbolt Door Lock with Passage Lever Matte Black

Responsible Party: Amazon.com Services LLC.
U.S. Contact Information: 410 Terry Ave N. Seattle, WA 98109 USA
Telephone Number: 206-266-1000

FCC Compliance Statement
This device complies with Part 1 S of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation

FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

Canada IC Notice
This Class B digital apparatus complies with Canadian CAN ICES-003(B) / NMB-003(B) standard.

Battery Disposal

• Do not dispose of used batteries with your household waste. Take them to an appropriate disposal/collection site .
• To learn more about recycling batteries, visit: call2recycle.org/what-can-i-recycle

Specifications

Electronic lock (for all)

Voltage/battery type: 6 V ==, 4x 1.5 V AA

Battery life: Up to 1 year with 4x AA batteries
Door thickness: 1-3/8-1-3/4″ (35-45 mm)
Backset: 2-3/8″ (60 mm)/ 2-3/4″ (70 mm)
Latch bolt: Steel latch bolt, full 1″ (25.4 mm) throw
Cylinder and keys: Kwikset keyway, 2 keys

Door handles (B08J4MPXH2, B08J4K95KV only)

Door thickness: 1-3/8-1-3/4″ (35-45 mm)

Backset : 2-3/8″ (60 mm)/ 2-3/4″ (70 mm)
Latch bolt: Zinc alloy latch bolt with 1/2″ (12.7 mm) throw

Door handles (B08J4MPXHJ, B08J4M6LJS only)

Door thickness: 1-3/8-1-3/4″ (35-45 mm)

Backset: 2-3/8″ (60 mm)/ 2-3/4″ (70 mm)
Latch bolt: Zinc alloy latch bolt with 1/2″ (12.7 mm) throw

Feedback and Help
We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.

Scan the ”QR Code” below with your phone camera or QR reader: If you need help with your AmazonBasics product, please use the website or number below.

amazon.com/gp/help/customer/contact-us
+1 877-485-0385
amazon.com/AmazonBasics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>