Omnisense 93272OM Joystick Controller User Guide
- June 5, 2024
- Omnisense
Table of Contents
Omnisense 93272OM Joystick Controller User Guide
What’s in the box
-
Joystick Controller
-
Mounting Decal
-
6.56ft (2m) Cable
-
2 X (M5 X 40) studs, washers, spring washers and nuts
Installation
The Joystick Controller must be panel mounted. When correctly installed, the top side (front) of the Joystick Controller is waterproof and suitable for open deck installation.
When mounting the Joystick Controller, select a location that provides the best ergonomics for controller operation. The housing of the Joystick Controller is designed to provide a stable grip while your thumb or finger moves the knob.
- The Joystick Controller has a flush back that can be easily fitted onto any flat surface. Select a suitable location close to your Multi-function Display (MFD)/Monitor.
- Using the Joystick Controller Mounting Decal provided, mark and cut out the space to mount the Joystick Controller.
- Drill the 0.24in (6mm) holes required for attaching the Joystick Controller.
- Mount the Joystick Controller and use the bolts provided to secure it in place.
Connecting the cable
Connect one end of the Joystick Controller Cable to the [Controller] port in
the Junction Box and the other end to the Joystick Controller.
Connecting the Joystick Controller
To connect your Joystick Controller, launch the User Interface (UI). Proceed to Settings > Controller and select [Scan]. The system will automatically scan for a Joystick Controller connected to the Junction Box.
Once the Joystick Controller is found, the serial number will be displayed. Select + to connect the Joystick Controller and it will be ready for use.
If the system is unable to locate the Joystick Controller, perform a factory reset to the Joystick Controller by holding down the and button simultaneously for 10 seconds. Upon completing the reset, select + again to connect the Joystick Controller.
Control buttons
Display controls are accessible by pressing the respective buttons on the
Joystick Controller. To access a setting/function, press the button marked
with the corresponding icon. Use the joystick to select and cycle through the
options available. To wake the camera from Standby mode, press and hold the
Power/Standby button.
Joystick Controller icon description
Below is the description of each icon for further understanding.
| Joystick|
- Move to navigate through menu items
- Adjust Zoom/Focus, Brightness & Contrast level
- Control camera movement (Pan & tilt)
---|---|---
| Enter|
- Press to confirm a selection
| Function|
- Programmable Shortcut Key (Choose from Home, NUC, Standby, Radar)
- Press to activate shortcut function
| Menu|
- Press to display available options
- Press to return to previous menu
| Color Palette|
- Press to open Color Palette
- Choose from six different color modes
| Zoom|
- Press to activate Zoom Slider
- Press to toggle between zoom levels
| Radar Track|
- Press to open Radar Track settings
- Press to activate radar tracking function
| Sensor Select| Press to toggle between Day and Thermal camera (Not available
for Ulysses Micro)
| Power/Standby|
- Press to open Power/Standby settings
- Select [Home] to return turret to preset home position
- Select [Standby] to park and stow turret
- Press & hold to wake turret from parked position
Accessing more information
For more information, please refer to the user manual that has been shipped with your camera or visit omnisense-systems.com to download the latest user manual.
Customer Support
Singapore
8 Penjuru Lane,
Singapore 609189
T: +65 6844 3191
United States
1881 West State Road 84,
Bldg. 1 Unit 102, Fort Lauderdale,
Florida 33315, United States
T: +1 954-316-6230
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>