Vacuum Cleaners ES285095 Cordless Vacuum and Mop User Manual
- June 5, 2024
- Vacuum Cleaners
Table of Contents
ES285095
Cordless Vacuum and Mop
Safety Instructions
- Users are forbidden to disassemble this product, otherwise, it may cause danger.
- Before cleaning or maintaining this product, please be sure to unplug and turn off the power.
- Do not touch the socket, power adapter or display when your hands are wet to avoid the risk of electric shock.
- Please use the power adapter specifically for this product when charging, if using other power adapters charging may lead to damage to the product.
- If the power adapter is damaged, please stop using it immediately and contact our professional maintenance personnel for replacement.
- This product is not intended for use by people with physical, sensory or intellectual impairments or people lacking experience and common sense (including children), unless supervised or instructed by others to ensure that they can use it safely.
- When using, if you find the machine leakage or motor temperature is a too high and strange noise, such as the body overheating, strange noise, odor, and other problems, please immediately stop using, and contact our after-sales service department for help.
- Do not get the machine wet, otherwise, there is a risk of fire and electric shock due to the short circuiting of the machine.
- Do not block the air inlet and outlet, so as not to overheat the machine.
- Do not soak the ground brush in water, so as not to burn the machine.
- Do not shake or collide the machine violently to avoid the inflow of sewage into the motor.
- When moving the machine, please keep the machine upright so that the sewage will not flow into the motor.
- Do not use when the water tank and sewage tank are not installed in place.
- Do not use this product to clean unextinguished heat sources such as cigarette butts or matches to avoid fire.
- Do not use this product to clean flammable and explosive or highly volatile liquids, such as gasoline, kerosene, paint, perfume, etc., which may lead to short circuits, or explosion.
- Do not use this product to clean the color powder or toner used inside the laser printer or copier to avoid fire or explosion.
- Do not use this product to clean sharp objects, such as glass fragments, nails, tacks, paper clips, stones and other items, to avoid damage to the product.
- Do not clean strong stains such as pigments, paints, shoe polish, etc.
- Please do not use this product to clean foam liquid, so as not to cause damage to the motor.
- Cleaning fluid should be placed out of reach from children.
- Please follow the floor cleaning liquid label instructions to use the cleaning liquid.
- Please do not add alcohol to the clean water tank.
Packing list
Before using this product, please check if the package contains the following accessories, if any is missing, please contact customer service. The below images are for reference only, please refer to the actual product received.
Product view
Digital Display
| | The indicator will light up white when the cleaner is in Eco Mode
---|---|---
| The indicator will light up white when the cleaner is in Max Mode.
| When the cleaner is doing normal cleaning, it shows the working time from
“switching on” to
“now”. When the cleaner is in self-cleaning mode, it shows the self-cleaning
countdown from “59” to
“0“ When the cleaner runs faulty, it shows the faulty code to help identify
the problem.
| The indicator will flash RED slowly when Dirty Water Tank is full, please
empty the Dirty Water Tank in time.
| The indicator will flash RED slowly when Clean Water Tank is short of water,
please fill up with clean water.
| The indicator will light up WHITE when the cleaner is in Self-cleaning Mode.
| Battery Indicator, the indicator will flash white slowly when charging, it
will stop flashing after fully charged
| The indicator will light up WHITE when the user is manually spraying water.
The indicators and the display may be slightly different with the final product, please subject to the actual product.
Product Installation
-
Handle disassembly and installation
1.1 Installation: Insert the handle connection tube to the body component port, and hear the “click” sound to mark the installation in place.
1.2 Disassembly: Use a suitable size screwdriver or Allen key, insert the thin hole located in the upper back of the body and press, while lifting the handle up.
-
Clean water tank installation: unscrew the cover of the clean water tank in accordance with Figure 2.1 below and load clean water, tighten the cover of the clean water tank clockwise in accordance with Figure 2.3, put it into the clean water tank in accordance with Figure 2.4, and hear a “click” to indicate that the installation is in place.
-
Dirty water tank installation: As shown in Figure 3.1, the bottom of the dirty water tank is placed at the opening of the body, and then pushed inward, and the “click” sound is heard to indicate a successful installation.
-
Roller brush installation: As shown in the figure below, please align the groove on the right side of the brush with the drive shaft and then press down on the left side of the roller brush until it is installed.
-
Roller brushes transparent window installation: as shown in the figure below, the first roller brushes transparent window cover below the snap good, the latch to the brush on the buckle, hear the “click” sound indicates that the installation in place.
-
Self-Cleaning and Charging station installation: insert the adapter charging port into the corresponding position of the charging station and the adapter head into the home socket.
How to use
-
Charging: As shown in the figure below, align the machine with the charging station, and the battery contact with the charging station contact in place to start charging.
-
Self-cleaning: When the machine is charging on the charging station, press the self-cleaning button to enter the self-cleaning mode. (Please make sure there is water in the clean water tank while using).
-
Use: Tilt the machine to the right angle and press the power button to start working.
Warning:
-If there is a large amount of foam in the dirty water tank during the working process, please clean up the dirty water tank in time to avoid the water flowing to the fan motor;.
-Prohibit fast pushing and pulling during the working process, so as not to cause the water to flow to the fan motor.
-While working, please be attentive to the dirt inside the dirty water tank, so as not to block the detector to affect the full water detection.
-Please turn off the power before charging.
Product Maintenance and Care
*Please unplug the power supply, turn off the machine, and remove the battery pack before maintenance and care.
-
Routine maintenance of dirty water tank: clean the dirty water tank and its shed immediately after each use, avoiding causing odor. Hold the dirty water tank handle by hand, press the lock buckle with your thumb and pull the dirty water tank out gently.
-
Routine maintenance of roller brush: please do the self-cleaning after each use. If the roller brush is too dirty, take out the roller brush according to the picture as below, and clean it by yourself.
-
Hepa daily maintenance, take out the HEPA from the dirty water tank as below, and please place it in the air vent to dry after cleaning.
Product Parameter
| Model: ES285095 | Product dimensions(mm):1150270250 |
|---|---|
| Working voltage(V):DC21.9V | Noise(dB):72dB |
| Rated power(W):150W | Adapter input:100-240V-50/60Hz 0.8A |
| Battery capacity(mAh):5000 | Adapter output:DC 27V 0.8A |
| Cleaning water tank(ml):600 | Charging time:6h |
| Dirty water tank(m1):550 | Endurance:ECO mode 50min |
MAX mode 40min
Net weight(kg):3.9|
The above data are from our lab, actual usage may vary depending on the
environment in which it is used. Please refer to the actual use.
Our company reserves the right to make any technical and design changes to the
product due to the continuous improvement of the product, and we reserve the
right to interpretation.
Cleaning/Replacement Frequency Recommended
| Part | Cleaning/Replacement Frequency Recommended |
|---|---|
| Clean water tank | Cleaning after each use |
| Dirty water tank | Cleaning after each use |
| HEPA | Cleaning after each use; Replacement every 3-6 months |
| Floater | Cleaning after each use |
| Brush guard | Cleaning after each use |
| Infrared sensor | Cleaning after each use |
| Roller brushes | Cleaning after each use; Replacement every 3-6 months |
Note:
The above frequency is only for your reference. The final cleaning/replacement
frequency should depend on the usage.
Trouble Shooting
| Problems | Possible Reasons | Solutions |
|---|---|---|
| The cleaner can not be charged. | The power supply does not connect well. | |
| The cleaner isn’t connected well with the charging station. | Please check the |
connection of the power supply.
Please replace the cleaner on the charging station.
The handle control doesn’t work.| The battery capacity is low.
The handle doesn’t connect well.
| Please check the battery capacity and fully charge it ? lease re-install the
handle.
The cleaner doesn’t work.| The dirty water tank is full.
The dirty water tank is not installed. The Roller brush is not installed.|
Please empty the dirty water tank.
check and install the
dirty y water ta tank.
Please check and install the roller brush.
The indicator display of clean water tank is incorrect.| uncalibrated.| Take
off the Clean Water tank, then start to dean and spray, turn cleaner off until
draining the pipe. Then press the “Switch Button° and °Eco/Max Button “for 5
seconds until the digital display flash two times, then cheth again.
The vacuum is getting weaker.| The Hepa is blocked. The Hepa is wet.| Please
check and clean the HEPA. Please dry the Hepa first.
The clean water tank is leaking.| The clean water volume is higher than the
snuffle valve.
The clean water tank is not installed well.
The cap is not screwed well.| Pour out water until the volume is lower than
the snuffle valve. Please re-install the water tank.
Please screw the cap well.
No water comes out when spraying.| The clean water tank is empty. The clean
water tank is not installed well.| Please fill up the Clean Water Tank.
°lease, re-install the water tank.
No voice assistance.| . The voice function is switched off. the version
excludes voice.| Turn on the voice switch. Please check and confirm with the
local seller.
The cleaner doesn’t work in self-cleaning mode.| The dirty water tank is full.
_ack of water.| Please empty the dirty water tank. Please fill up the clean
water tank.
There are water drops at air outlet.| The Hepa is not installed. The hepa is
not dry.
The cleaner was tilted hard. Cleaner vacuums the foam liquid.| Please check
and install the HEPA. PIS dry the hepa before use. Use the machine correctly.
Empty the dirty water tank in time.
The cleaner moves hard.| The roller brush is not installed well.| Please check
and re-install the Roller Brush as a guide.
The indicator displays the dirty water tank is full while it’s not| The
cleaner vacuums too much foam liquid.| Clean the foam liquid immediately.
Fault code table
| Error Code | Causes | Solutions |
|---|---|---|
| E 1 | Battery disconnect | Replace battery |
| E2 | Rechargeable battery voltage is | |
| too low | Replace the battery | |
| E3 | Rechargeable battery voltage | |
| difference is too large | Replace the battery | |
| E4 | Temperature control of battery is | |
| abnormal | Replace the battery | |
| E5 | High discharging temperature | Battery pack over-temperature,do not use |
until the battery
temperature is restored
E6| High charging temperature| Battery pack over-temperature,do not charge
until the
battery temperature is restored
E7| Low charging temperature| make sure the ambient temperature is above 5°C
Fl| Charging over-current| Please confirm whether the charger is original
F2| short-circuit protection| Please contact customer service
F3| Discharge Over-current| Please contact customer service
F4| Roller brush Discharge Over-current| Check whether there is any foreign
body to be cleaned at the roller brush. If the fault still exists, please
contact customer service
F6| No dirty water installed| Install dirty tank before use