LA CROSSE TECHNOLOGY 817-83957 Projection Alarm Clock with 2 AMP USB Charging and FM Radio User Guide

LA CROSSE TECHNOLOGY 817-83957 Projection Alarm Clock with 2 AMP USB

Charging and FM Radio

Power Up

1.  Insert the 5.0-volt power adapter into an outlet, then into your clock. Optional: Insert a CR2032 battery (not included) for backup.

2.  Enter the Settings Menu to set Time. 5.0 V adapter (included)
   Settings Menu

3.  Hold the button to enter the Settings Menu.

4.  Press the or button to adjust the values. Hold to adjust quickly.

5.  Press the button to confirm and move to the next item.

Settings Menu
Settings Menu Order:
• Hour
• Minutes
• Snooze Duration (NO5) 5-60 minutes
Note: When setting the Hour, the “P” will show to indicate PM hours.

FM Radio

1. Extend the antenna for best reception.
2. Press the button to listen to the radio. ON will show briefly, followed by the frequency in MHz.
3. Press the or button to select station. Hold to search for next clear station.
4. Press to view Volume Setting. Use or button to adjust Volume (1-16).
5. Press to turn radio off.

FM Radio

Auto Scan and Store Preset Stations:

1.  Press to listen to the radio

2. Hold to automatically scan and set up to 20 stations.
   Manually Store Preset Stations:

3.  Press the button to listen to the radio. ON will show briefly.

4.  Press the or button to select station.

5.  Hold until P01 flashes to store as Preset 1.

6.  Repeat steps 2 and 3 to set up to 20 Preset Stations. Note: You can change preset stations with the above instructions.
   Listen to Preset Stations:

7.  Press the button to listen to the radio.

8.  Press then or to select Preset Stations.
   Radio Sleep Timer:

9.  When the radio is on, hold , the sleep time “05” (5 minutes) will show.

10.  Press repeatedly to select minutes from 05, 10, 15, 30, 45, 60, 75, 90 or OFF.

11.  The clock radio reverts to the time display automatically in a few seconds. Hold to see the sleep time remaining.

12.  Press to deactivate the radio and the sleep function before the sleep time has elapsed.

Time Alarm

This Projection Clock has a dual time alarm function. Use the following instructions to set your alarm times, choose your wake up sound (buzzer or radio), and alarm volume if you choose the radio option.
Set Alarms:

1.  Hold the button to enter the Alarm Settings.

2.  Press the or button to adjust the values. Hold to adjust quickly.

3.  Press and release the button to confirm and move to the next item.

4.  Press the button anytime to save and exit.
   Alarm Settings Order:

   •  Alarm 1 Hour
   •  Alarm 1 Minutes
   •  Alarm 1 Wake sound: bu (buzzer) or rd (Radio)
   •  When rd (Radio) is selected: Alarm 1 HI/LO (volume)
   • Alarm 2 Hour
   •  Alarm 2 Minutes
   • Alarm 2 Wake sound: bu (buzzer) or rd (Radio)
   •  When rd (Radio) is selected: Alarm 2 HI/LO (volume)

Projection

Projection ON/OFF:
The Projection will be On when the Projection Alarm Clock is powered on.
1. Press the button to turn Projection Off, Dim, or On again

Projection Image Rotation:
1. Hold the button to turn the Projection 180 degrees.
2. Turn the Projection Wheel on the back of the Projection Arm to adjust the projected image 90 degrees.
Note: The Projection Wheel will rotate to allow you to correctly project the time onto your wall or ceiling.

USB Charging

•  Make sure the original adaptor (5V-2A) enclosed with your clock radio is being used to power your clock radio.

• Connect your external device’s USB charging cable (not included) to the
  USB Charging Port.

•  Charging times will vary.

•  USB Power Output: 2A maximum current.

•  Charge 2A devices or devices that are self-regulating.
  Note: This clock was designed to charge tablets or other devices requiring more than a 2A current.

Adjustable Backlight

Select High or Low:
Press the button to select High or Low backlight. Backlight will dim but does not turn off.
Adjust Low Brightness:
Rotate the Dimmer Wheel on the side of your clock to adjust the brightness of the Low setting. The High setting is not adjustable

We’re Here to Help

If you require additional support, get in touch with our friendly customer support team based in La Crosse, WI. Phone: 1.608.782.1610 Online: bit.ly/contact_techsupport Our knowledgable customer support team is available: Mon-Fri 8am-6pm CST

Care + Maintenance

• Do not mix old and new batteries.
• Do not mix Alkaline, Lithium, standard, or rechargeable batteries.
• Always purchase the correct size and grade of battery most suitable for the intended use.
• Clean the battery contacts and also those of the device prior to battery installation.
• Ensure the batteries have been installed with correct polarity (+/-).
• Remove batteries from equipment that will not to be used for an extended period.
• Promptly remove expired batteries

Specifications

1. Projection Alarm Clock (817-2410 | 817- 83957)

2. Power Requirements:

3. 5V AC/DC adapter (included) KA1201A-0502000US
   Optional Backup: CR2032 battery (not included) The plug on the power adapter is intended to serve as the disconnect device, the socket outlet shall be installed near the equipment and shall be easily accessible.

4. Dimensions: 7.75” W x 1.97” D x 3.74” H

5. (19.7cm W x 5.0cm D x 9.5cm H)

6. USB output: 2A maximum current.
   Note: This is only a power output USB device and a USB cord cannot power the alarm itself.

7. Alarm duration:
   Buzzer 5 minutes / Radio 1 hour Snooze duration: 5-60 minutes programmable

Warranty Info

Crosse Technology, Ltd. provides a 1-yea  limited time warranty (from date of purchase) o this product relating to manufacturing defects inmaterials & workmanship. La Crosse Technology, Ltd, 2830 S. 26th St. La Crosse, WI 54601 For Full Warranty Details, Visit: www.lacrossetechnology.com/pages/warranty

References

• Warranty – La Crosse Technology
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>