Dynetix Motorhelm Headset Instruction Manual

: June 13, 2024
: Dynetix

Table of Contents

Dynetix Motorhelm Headset
Product Usage Instructions
Parts included
Battery Caution
Headset diagram
- Headset functions
Installation process
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Dynetix Motorhelm Headset

Product Information:

Product Name: Helm Communicatie
Product Type: Headset
Compatible Devices: Any device supporting Bluetooth
Included Parts: Refer to the user manual
Battery Caution: Follow the battery usage guidelines
Automatic Functions: Explore the automatic features of the headset

Product Usage Instructions

To adjust the volume, hold the button until the sound level is to your liking.
To perform a single click action, press the button once.
To perform another single click action, press the button again.
To charge the battery, connect the device. The LED will turn red during charging and turn off when fully charged.
To install the headset on your helmet:
Ensure that the Dynetix does not block any helmet functions.
Attach the clip on the left side of the helmet using the threads.
Attach the microphone on the left side of the helmet, making sure it fits properly inside.
Attach the speaker on the right side of the helmet, behind the cushions or helmet strap.
If necessary, stick velcro pads on the left side of the helmet for better microphone and speaker placement.
Ensure the microphone runs behind the helmet cushions and fits properly.
Secure the velcro pads previously placed and make sure the microphone is positioned correctly.
Place the speaker behind the cushions or inside the slit as shown in the user manual.

Stay connected, stay safe with Dynetix!

Parts included

BT-12 Intercom with Speakers & Microphone
2x Pop filter
Micro-USB Charging cable
Attachment piece
2x Screw
Velcro pads

Battery Caution

Make sure not to overcharge the battery frequently.
Make sure that the intercom does not get too hot, e.g. Leave it in the sun for too long
Don’t throw away in garbage container, contains Lithium battery

Headset diagram

Headset functions

On / Off
Hold butten for 3 seconds untill the sound reminder “Power on”.
Bluetooth pairing
Hold button for 3 seconds, when the sound reminder
“Power on” louds keep holding button untill you hear the reminder “Pairing”.
Pauze / Play
Press button once to pause or to play.
Previous song
Press button once.
Next song
Press button once.
Volume down
Hold button untill the volume is to your liking.
Volume up
Hold button untill the volume is to your liking.
Answer call
Press button once.
End call
Press button again.

Automatic functions

Automatic reconnect
The headset automatically connects with the most recently paired device.
Automatic pairing mode when the most recently paired device is not in range or online, the headset will automatically enter bluetooth pairing mode.
Power saving mode 5 minutes after no device has been connected the headset will automatically turn off.
Low battery warning
When you hear “Power low” the battery is 20% or less

Bluetooth understand

Charging time
Total charging time of 2 hours.
Charging port
Micro-USB
LED indicator
During charging the led turns red, when the battery is fully charged the led turns off.

Installation process

Stap 1
Use a screwdriver to loosen the threads.

Stap 2
Put the Dynetix headset on the left side of the helmet with the usage of the clip.

Stap 3
Find the best position for the Dynetix, make sure it doesnt block any functions on your helmet

Stap 4
Remove the cushions from the helmet and grab the velcro pads.

Stap 5
Stick the velcro pads on the right side of the helmet. Behind the cuchions or behind the helmet strap.

Stap 6
Put the speaker with the microphone on the left side of the helmet. Make sure it fits properly inside the helmet

Stap 7
Once you have found the best location for the microphone and speaker you can also stick the velcro pads on the left side of the helmet.

Stap 8
Stick both speakers on to the previously placed velcro pads. Make sure the microphone runs behind the helmet cuchions.

Stap 9
Lay the cabels behind the cuchions or inside the slit as seen in the last picture.

Warning!
Every helmet is different, with some helmets the installation process is easy and doesnt take long. With others the process is more difficult and it will be necessary to remove the head cuchions.