SIEMENS TW86105P Kettle Instruction Manual

: June 5, 2024
: SIEMENS

Table of Contents

SIEMENS TW86105P Kettle
INTRODUCTION
Safety instructions
Parts and operating controls
Cleaning and maintenance
Descaling
Troubleshooting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SIEMENS TW86105P Kettle

product

INTRODUCTION

fig-1

Safety instructions

Please read and follow the operating instructions carefully and keep them for later reference. Enclose these instructions when you give this appliance to someone else.
This appliance is designed for the preparation of normal household quantities in the home, or in household-like, non-commercial environments.
Household-like environments include staff kitchens in shops, offices, agricultural and other small businesses or for use by guests at bed-and-breakfast establishments, small hotels and similar residential facilities.

A Danger of electric shock

The appliance may only be connected to a power supply with an alternating current via a correctly installed socket with earthing. Ensure that the protective conductor system of the domestic supply has been correctly installed.
Connect and operate the appliance only according to the type plate specifications. To avoid potential hazards, repairs such as replacing a damaged cable must only be carried out by our customer service personnel.
This appliance can be used by children aged from 8 years and above and by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
Keep children under 8 years of age away from the appliance and connecting cable and do not allow them to use the appliance.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 years and supervised.
Avoid spillage on the connector. Never immerse the appliance, base or mains cable in water.
Use the kettle only with the included base.
Use only if power cord and appliance show no signs of damage. Should a fault occur, pull the plug or disconnect from the mains immediately.

A Risk of fire

Do not place the base or the kettle on or near hot surfaces such as a cooker or hob.

A Risk of scalding

The appliance heats up during use. Make sure you only pick it up by the handle and do not open the lid until the appliance has cooled down. Only use the appliance when the lid is engaged.
If the appliance is filled above the “max.” marking, there could be a risk from splashes of boiling water.

A Risk of burns

After the use the heating element surfaces and warming plate can be subjected to residual heat.
Do not use near water contained in bathtubs, sinks or other containers.

A Risk of suffocation

Do not allow children to play with packaging material.

A Risk of injury

Misuse of the appliance can potentially lead to injury.
Congratulations on purchasing this Siemens appliance.
You have acquired a high-quality product that will bring you a lot of enjoyment.

Parts and operating controls

Kettle (with water level indicator)
Lid
Lid release button
ON/OFF O switch
Temperature indicator (illuminated)
+ – button (temperature setting)
U button (keep warm)
Limescale filter (removable)
Base
Cable tidy

important: Use the kettle 1 only with its included base 9

Only fill the kettle with water. Milk and instant beverages will burn and damage the appliance. Never operate the kettle 1 without water and do not overfill it; observe the min and max markings.
If the kettle is too full, the water will boil over.

Before using for the first time

Remove any stickers or film.
Unroll the right amount of cable from the cable tidy 10 and plug it in.
Fill the kettle 1 with water. Bring the water to a boil and discard it. Repeat the procedure. This will make sure that the kettle is clean for normal use.
When the water comes to a boil for the first time, add a tablespoon of white vinegar.

Boiling water

Fill the kettle with fresh water through the spout or the open lid 2 (press lid release button 3).
Check the amount by reading the water level indicator markings (min and max).
Close the lid 2 until it locks and place the kettle 1 on the base 9.
Press the O ON/OFF switch 4. The kettle emits a signal, and the factory-set temperature (100°C) lights up. The water is being heated.
By pressing button 6 + or – you can set the temperature to ca. 70°C, ca. 80°C, ca. 90°C or ca. 100°C.
When the water has reached the selected temperature, the kettle will switch off automatically, the temperature indicator 5 goes off, and a signal sounds.

Note

The selected temperature can be changed at any time while the kettle is heating up. While the kettle heats up, the current temperature lights up; the preset temperature flashes until it has been reached.
If the temperature cannot be set, this indi-cates that the water in the kettle is hotter than the desired temperature. The current temperature will light up.
You can turn off the kettle at any time by pressing the O ON/OFF switch 4 again.

Warning

If you remove the kettle 1 from the base and replace it before the heating process is over, the kettle will not continue to heat the water. The selected settings will be lost (reset to factory setting).

N.B

Use the kettle only while the lid 2 is closed and the limescale filter 8 is in place. For physical reasons, base 9 may collect some condensation water. This is normal; it does not mean that the kettle 1 leaks.
When you set the temperature to 100°C, the kettle will turn off only after the water has reached the boiling point, i.e. it will bubble for a short period of time.
After boiling, let the kettle cool down for 5 minutes before refilling it with water.
Do not turn on the appliance if the kettle 1 is empty, otherwise, the overheat control will engage and the appliance will switch itself off automatically.

Keep warm setting

You can turn on the keep warm with any temperature setting.
Press button 7. U lights up, and the function is activated. To turn it off, press button 7 again. The U indicator goes off.
The keep warm feature switches off automatically after 30 minutes. The kettle emits a signal.

Cleaning and maintenance

Risk of electric shock

Never immerse the device in water or place it in the dishwasher!
Do not steam-clean the appliance.
Before cleaning, unplug the appliance from the power outlet.
Clean the outside of the kettle 1 and base 9 with a damp cloth. Do not use strong or abrasive cleaning agents.
Remove the limescale filter 8, soak it in a little vinegar, then rinse clean with clear water.
Rinse the kettle 1 and the limescale filter 8 with clear water.
Clean the stainless steel surface with a commercial stainless steel care product.

Descaling

Regular descaling

makes your kettle last longer.
ensures proper function.
saves energy.

Descale the kettle 1 with vinegar or a commercial descaling agent.

Fill the kettle 1 with water up to the 1.5 mark and bring to a boil. Next, add a small amount of white vinegar and let it sit for several hours.
You can also use a commercial descaling product and follow the manufacturer’s instructions.
Rinse the kettle 1 and the limescale filter 8 with clear water.

Warning

Never use hard objects to remove limescale residue as this will damage the seal.
If you use the kettle daily, descale more frequently.

Troubleshooting

The kettle does not heat up; the temperature indicator 5 does not light up.
The overheat control has tripped.
Let the kettle 1 cool down for some time so that the appliance can be switched on again.
The unit turns off before the water comes to a boil.
The kettle contains too much scale.
Descale the kettle as per the instructions.