IDea FCS Series Professional Ceiling Speaker User Manual
- June 5, 2024
- iDea
Table of Contents
FCS Series
Professional Ceiling Speakers
Altavoces de Techo Profesionales
User Manual
Warnings
The information furnished in this manual does not include all of the details
of the design and engineering of this particular product nor does it cover
every possible application or situation concerning its usage, which may occur
during the installation, operation, or maintenance of the product.
IMPORTANT
THE PRODUCT REQUIRES CLASS 2 OUTPUT WIRING
CAUTION
TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE THE TOP OR BOTTOM COVERS. NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DISCONNECT THE POWER CORD BEFORE REMOVING THE REAR PANEL COVER TO ACCESS THE
GAIN SWITCH.
SHOCK HAZARD – DO NOT ENTER
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE!
MAGNETIC FIELD
CAUTION: Do not locate sensitive high-gain equipment such as
preamplifiers or tape decks directly above or below this unit.
Because this amplifier has a high power density, it has a strong magnetic
field which can induce hum into unshielded devices that are located nearby.
This field is strongest just above and below the unit. If an equipment rack is
used, we recommend locating the amplifier(s) at the bottom of the rack and the
preamplifier or other sensitive equipment at the top.
The lightning bolt triangle is used to alert the user to the risk of electric shock The exclamation point triangle is used to alert the user to important operating and /or maintenance instructions.
Technical Data | FCS4T
| Tweeter | 0.5” (13 mm) Silk soft dome |
|---|---|
| Woofer | 4” (100 mm) Graphite Cone, Rubber Surround |
| Frequency Range +/-3 dB | 98 Hz – 20 kHz |
| Power Handling RMS | 40 W program, 20 W (IEEE 219) |
| Sensitivity (1 W / 1m) | 84 dB |
| Coverage | H:80° – V:70° |
| Crossover Frequency | 4 kHz |
| Conformity (Input) | 100 V (8 Ω) |
| Taps | 8 Ω,0, 20 W, 10 W, 5 W, 2.5 W |
| Impedance | 8 Ω |
| Termination | Standard pressed connector |
| Included Accessories | Cutout template grille |
| Attachment | Low-profile grille |
| Dimensions (H x D) | 160 x 197 mm (6.29” x 7.75”) |
| Weight | 2.17 kg (4.8 lb) |
| Cut out diameter | 175 mm (6.88”) |
| Material | ABS + iron |
Technical Drawings | FCS4T
Technical Data | FCS5T
| Tweeter | 0.75” (20 mm) Titanium dome |
|---|---|
| Woofer | 5” (125 mm) Graphite Cone, Rubber Surround |
| Frequency Range +/-3 dB | 85 Hz – 20 kHz |
| Power Handling RMS | 60 W program, 30 W (IEEE 219) |
| Sensitivity (1 W / 1m) | 84 dB |
| Coverage | H:40° – V:30° |
| Crossover Frequency | 2.8 kHz |
| Conformity (Input) | 100 V (8 Ω) |
| Taps | 8 Ω,0, 30 W, 15 W, 7.5 W, 3.25 W |
| Impedance | 8 Ω |
| Termination | Standard pressed connector |
| Included Accessories | Cutout template grille |
| Attachment | Low-profile grille |
| Dimensions (H x D) | 229 x 230 mm (9.01” x 9.05”) |
| Weight | 2.8 kg (6.17 lb) |
| Cut out diameter | 206 mm (8.11”) |
| Material | ABS + iron |
Technical Drawings | FCS5T
Technical Data | FCS6T
| Tweeter | 1” (25 mm) Titanium dome |
|---|---|
| Woofer | 6.25” (165 mm) Graphite Cone, Rubber Surround |
| Frequency Range +/-3 dB | 65 Hz – 20 kHz |
| Power Handling RMS | 80 W program, 40 W (IEEE 219) |
| Sensitivity (1 W / 1m) | 86 dB |
| Coverage | H:55° – V:45° |
| Crossover Frequency | 3.5 kHz |
| Conformity (Input) | 100 V (8 Ω) |
| Taps | 8 Ω,0, 40 W, 20 W, 10 W, 5 W |
| Impedance | 8 Ω |
| Termination | Standard pressed connector |
| Included Accessories | Cutout template grille |
| Attachment | Low-profile grille |
| Dimensions (H x D) | 236 x 257 mm (9.01” x 10.11”) |
| Weight | 3.3 kg (7.28 lb) |
| Cut out diameter | 226 mm (8.90”) |
| Material | ABS + iron |
Technical Drawings | FCS6T
Installation
STEP 1
Using a stud finder (available at low cost at most hardware stores) or another
accurate method, locate the center point between two joists and mark. Using
the template provided, trace a hole pattern on surface of the ceiling.
STEP 2
Using a saber saw, keyhole saw, or very sharp utility knife cut a hole in the
ceiling. Following trace pattern.
STEP 3
Run loudspeaker wire to sound source location. There are several methods you
can use to accomplish wiring, depending on the construction characteristics of
the room or house. You can add a professional touch to your installation by
using a speaker terminal plate at the source location. Leave a sufficient
amount of wire at the speaker location (8-10 inches / 20-25 cm) to complete
the connection.
STEP 4
Attach loudspeaker wires to speaker terminals, observe correct polarity, and
position speaker frame up into cutout. Be careful not to pinch wires in the
process.
STEP 5
Carefully tighten the four mounting screws. This will cause the mounting wings
to rotate behind the mounting surface and secure the speaker in place. STEP
6
After the speaker panel is secured tightly, test the sound. When you are
satisfied the speaker is operational, then affix grill. As grill is designed
for a snug fit you’ll need to position one edge into slot first and press or
squeeze around perimeter of grill, while pushing the leading edges into the
grill slot.
NECESSARY TOOLS
- Hammer
- Cross-headed screwdriver
- Paintbrush
- Keyhole saw
- Tape measure
- Pencil
Service
This unit has very sophisticated circuitry and should only be serviced by a
fully trained technician. This is why each unit bears the following label:
CAUTION
To prevent electric shock,do not remove covers. No user-serviceable parts inside. Refer servicing to a qualified technician.
Worldwide service
Service may be obtained from your local authorized service center. To obtain
service, simply present your sales receipt as proof of purchase along with the
defective unit to an authorized service center. They will handle the necessary
paperwork and repair.
Remember to transport your unit in the original factory packaging.
- When sending a product to an authorized service center for service, be sure to fill out the service information form and include it inside your unit’s shipping pack. Do not send the service information form separately.
- To ensure the safe transportation of your unit to the authorized service center, ship it in an original factory-packing container.
- Do not ship the unit in any kind of rack. Ignoring this warning may result in extensive damage to the unit and the equipment rack.
Accessories are not needed. Do not send the instruction manual, cables, and any other hardware.
WEEE Mark
If you want to dispose of this product, do not mix it with general household
waste. There are separate collection systems for used electronic products in
accordance with legislation under the WEEE Directive (Directive 2002/96/EC)
effective only within the European Union.
Warnings!
- Read this document thoroughly, follow all safety warnings and keep it for future reference.
- The exclamation mark inside a triangle indicates that whatever repairing and component replacement operations must be done by qualified and authorized personnel.
- No user-serviceable parts inside.
- Only use accessories tested and approved by IDEA and supplied by the manufacturer or an authorized dealer.
- Installations, rigging, and suspension operations must be done by qualified personnel.
- Only use accessories specified by IDEA, complying with maximum loads specifications and following local safety regulations.
- Read the specifications and connection instructions before proceeding to connect the system and use only cabling supplied or recommended by IDEA. Connection of the system should be done by qualified personnel.
- Professional sound reinforcement systems can deliver high SPL levels that may result in hearing damage. Do not stand close to the system while in use.
- Loudspeakers produce magnetic fields even while they are not in use or even when disconnected. Do not place or expose loudspeakers to any device that is sensitive to magnetic fields such as television monitors or data storage magnetic material.
- Disconnect the equipment during lightning storms and when it is not to be used for a long time.
- Do not expose this device to rain or moisture.
- Do not place any objects containing liquids, such as bottles or glasses, on the top of the unit. Do not splash liquids on the unit.
- Clean with a wet cloth. Do not use solvent-based cleaners.
- Regularly check the loudspeaker housings and accessories for visible signs of wear and tear, and replace them when necessary.
- Refer all servicing to qualified service personnel.
- This symbol on the product indicates that this product should not be treated as household waste. Follow local regulations for recycling electronic devices.
- IDEA declines any responsibility from misuse that may result in malfunction or damage of the equipment.
Warranty
- All IDEA products are guaranteed against any manufacturing defect for a period of 5 years from the date of purchase for acoustical parts and 2 years from the date of purchase for electronic devices.
- The guarantee excludes damage from the incorrect use of the product.
- Any guarantee repair, replacement, and servicing must be exclusively done by the factory or any of the authorized service centers.
- Do not open or intend to repair the product; otherwise servicing and replacement will not be applicable for guaranteed repair.
- Return the damaged unit, at shipper’s risk and freight prepaid, to the nearest service center with a copy of the purchase invoice in order to claim guaranteed service or replacement.
Tel. +34 881 545 135
www.ideaproaudio.com
info@ideaproaudio.com
Specifications and product appearance may be subject to change without notice.
IDEA_FCS-Series_User Manual_BIL_v1.1 | 04 – 2021
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>