DISTEC POS-Line BLO Series Industrial Grade Monitors User Manual

POS-Line BLO Series Industrial Grade Monitors
User Manual
POS-Line monitors from 80 cm (31.5“)

Copyright
The contents of this manual are subject to change without notice.
© 2022 Distec GmbH. All rights reserved.
Reproduction of this manual in parts or in entirety without the previous authorization of Distec GmbH is prohibited.
Distec GmbH is not liable for errors and collateral or subsequent damage which result from supply, deployment, or any other utilization of this document.
All product names mentioned in this document are trademarks or registered trademarks of their due owners.

General Specifications

Scope of Document
This user manual is valid for POS-Line FLO monitors from 80.0 cm (31.5”) up to 116.8 cm (46“). The POS-Line BLO monitors are offered in different screen sizes. All monitors are equipped with a special F30 fire protection glass and a temperature fuse for voltage-free switching from a certain temperature. The series is designed for use in fire load and flue gas-sensitive environments.
Important note: This user manual is complemented by other additional documents when indicated.
All documents are also available for download from the Distec website: www.distec.de/en.
POS-Line monitor versions:

POS-Line PME BLO:| Monitor with integrated controller, 1 x RGB, 1 x HDMI, 1 x Display Port.
---|---
POS-Line IQ BLO:| Monitor with integrated PC Intel ® Celeron ® J3455 (1,5GHz/2,3GHz).

Scope of Delivery

When unpacking the monitor, please check if the following accessories are included in the shipment:
Note: Pictures can differ from actually supplied products.

***** Cable may vary depending on the country

General Safety Regulations

Safety information
Please read this safety information carefully for your personal safety and for the prevention of property damage.
In case of a malfunction, immediately disconnect the power plug and contact your dealer or the next Data Display Group service center. A malfunction is also considered if the housing, a control element, or cable is damaged or if liquids or other objects penetrate the monitor.
Please read the safety information carefully before installing the device. If you have any doubts about whether the device may be used in a particular environment, please contact our service partner.
Repairs
Repairs may only be carried out by authorized technical personnel. Unauthorized access or improper repairs might cause serious property damage or cause danger to the
user. In addition to that, any legitimate warranty claim expires.
Electrical connection
Disconnect the monitor from the socket before executing any work. Do not touch or connect data cables or power cables during thunderstorms.
System start-up
Before the system start-up let the monitor adjust to the room temperature. Do not expose the device to direct heat sources. In case of condensation, please wait a minimum of 12 hours before switching on the monitor. The monitor shall only be installed and used according to this documentation datasheets. Only qualified personnel may perform the initial installation and system setup.
Qualified personnel
Qualified personnel, in terms of the safety information of this documentation, are persons who are qualified to activate, ground, and label devices, systems, and circuits according to the safety standards.
Operation
For proper and safe utilization of the product, adequate transportation, storage, installation, assembly, careful handling and maintenance are essential. The device is only certified for in-door operation. Extreme ambient conditions shall be avoided and the monitor shall be protected from dust, humidity, and heat. Do not expose the monitor to direct sunlight.
Transport
Unpack the monitor at the place of installation. Use only original packaging for transportation. Please observe these rules for any later transport.
Condensation
Avoid condensation during transport at low temperatures or at extreme fluctuations of temperature.
Safety guidelines for the handling of LCD monitors

| • If the device is not used for a long period of time, unplug the power cable.
• Do not unplug the power cable while the device is powered on, except for emergencies.
• To unplug the device without problems, sockets have to be easily accessible.
• Ensure that the power cable does not get pinched or kinked.
• Do not place heavy objects on the power cable.
---|---
| • Do not use damaged or lose sockets to plug in the device.
• Plug the device in earthed sockets only.
• Operate the device with the power cables included in the delivery packet only.
• Use undamaged power cables only.
• When plugging in and out, do not touch the power cable with wet hands.
• Ensure that the power cable is plugged in the socket safely and correctly.
• Use for devices with external power supply only the supplied original power supply, or
an equivalent Low Power Source (LPS).
| • Do not use an extension block to plug several devices into a single socket.
| • According to the size, devices may be difficult to handle and very heavy. Ensure that at
least two people lift and carry the device.
• Put down the device slowly and carefully to avoid damaging the LCD screen. Ensure that the device stands stable.
• Keep packaging away from children. The danger of suffocation!
• Use our specified and professionally mounted wall mounting only.
| • Do not put objects onto the device.
• Do not place candles, heaters, or humidifiers near the device.
• Keep the device away from fireplaces and flammable materials.
| • Ensure sufficient ventilation of the device.
• Keep a minimum distance of at least 10 mm devices to the wall, for devices with integrated PC of at least 40 mm.
• Ensure compliance with the operating temperature.
| • Do not install the device in places where it is exposed to environmental impacts such
as rain or direct sunlight.
• Do not install the device in places where it is exposed to high humidity, dust, or smoke.
In case of doubt, please contact your sales partner.
| • Please use a soft, moist cloth for cleaning.
• For cleaning the screen, please use only commercially available screen cleaner. Do not
spray the cleaner directly to the device but onto a cloth.
• Please clean ventilation slots regularly to ensure good air circulation.
| • Protect your device from water splash.
• When cleaning, please make sure that no liquids get into the device.
• Screens and surfaces can be easily scratched. Therefore, please use the prescribed
cloth only.
| • Attention! High voltage! Never open the device by yourself.
• In case of unusual noises, burnt smell or smoke unplug the power cable.
• Do not insert objects into the device through the ventilation slots.
• If the same picture is displayed over a longer period of time, an after- image may arise.
• When exchanging batteries for remote control, pay attention to the polarity. Keep batteries away from children and ensure environmentally correct disposal.

First Installation

Position of connectors and controls
All connectors for power and cables are located at the bottom of the backside of the display.

Mounting
Distance to wall:

• devices without integrated PC: min.10 mm
• devices with integrated PC: min. 40 mm

Mounting with VESA compatible brackets
POS-Line displays are shipped with factory-installed mounting angles for VESA compatible brackets. The mounting angles are, without further modification suited for landscape or portrait mode and comply with the minimum required distances between the backside of the display and the wall. The operating position of the device is perpendicular (90 degrees to the floor). Pay attention to the permissible tilt angle for wall mounting.
The device can be operated both in landscape mode and in portrait mode. The information is for positioning to note on the back of the device, always.
For mounting on the pre-assembled VESA brackets, a suitable wall bracket must be used whose load-bearing capacity corresponds to the weight of the monitor. For fastening to the VESA brackets, use 4 metal screws of size M6x25.

VESA standards:
31.5“ – 54.6“ displays: MIS-F 400 x 400 mm (M6)

Allowed tilt angle for mounting
Attention! All monitors are to be mounted only with a tilt angle of 0°— -30°.

Connecting to power
POS-Line displays require a voltage of 110V – 230V AC.
Note: Install all data cables to external devices before connecting the display to power.

• Switch the on/off switch in position off.
• Connect the power cable to the display.
• Connect the power cable to a power socket.
• Switch the display on.

POS-Line Video PME BLO

Connectors and OSD buttons of POS-Line Video PME BLO series

Connecting to a PC with a VGA cable

Connecting to a PC with an HDMI-DVI cable

Connecting to a PC with an HDMI cable

Connecting to a PC with a DisplayPort cable

Connecting the Remote-OSD to a PC with a USB cable

Remote OSD control
You can control the monitor remotely from an external computer. To do this, connect the monitor and computer as described above with a USB cable. Please read the instructions for the remote control, which you can find on our homepage: https://www.distec.de/en/service/downloads/monitore-downloads/.
OSD keyboard
OSD functions of the monitor can be controlled via an OSD keypad. The OSD allows the selection of input sources and fine-tuning of various
functional parameters like brightness, contrast, etc.

The OSD control can either be used:

• to access various functions directly
• to navigate within the OSD

The following two tables give an overview of the functions:
Direct functions:

Navigation in OSD menu:

The green/red LEDs (single package) on the external keypad show the current status of the board:

OSD menu

Image Menu

Brightness:| Panel brightness adjustment.
Contrast:| Panel contrast adjustment.
Hue:| Panel hue adjustment.
Saturation:| Panel saturation adjustment.
Sharpness:| Panel sharpness adjustment.
Color:| Opens the color sub-menu.

Color Sub Menu

Auto:| Performs auto color adjustment.
Color Temp:| Allow selection of different color temperature schemes, predefined and custom. Available if color
space of input is RGB.
Full color:| Select full received color space.
SRGB:| Selects SRGB color space.
XVYCC:| Selects XVYCC color space.

Display Menu

Auto-adjust:| Performs auto-adjustment on the VGA input image.
Phase:| This function is a slider to adjust the sampling phase of the analog interface. For optimum image quality, input pixels should be sampled at the ideal sampling points.
Clock:| This function is a slider to adjust the sample clock of the analog interface. This is helpful for improving the image quality for non-standard display modes.
Position:| Used to alter the placement of the image.

Move Position Sub Menu

Arrows:| Use arrow keys to move the position of the image on the screen.

Sound Menu

Volume:| The slider bar to adjust the volume.
Mute:| Mutes audio.
Output:| Chooses between speakers and headphones. Only one can be active at a time (Speakers are not available for POS-Line monitors).

Output Sub Menu

Speakers:| Toggles speakers on/ off.
Headphone:| Toggles headphones on/ off.

System Menu

Input source:| Sub menu to select the input source.
OSD settings:| Submenu for OSD settings.
Factory reset:| Submenu for Factory Reset.
EDID settings:| Submenu for EDID settings.
FW Revision:| Firmware revision.
OSD Revision:| OSD revision.

Input Sub Menu

Display Port:| Select the display port as the input signal.
VGA:| Select VGA as the input signal.
DVI/HDMI:| Select DVI/ HDMI as the input signal.
Auto Scan:| Enable/ disable input auto-scan.

OSD Settings Sub Menu

Timer:| Submenu for timer settings.
Rotation:| Submenu for rotation settings.
Position:| Submenu for image position.
Transparency:| Slider to set transparency.

Timer Sub Menu

Timer:| Selects how many seconds the OSD will remain active after the last use.

Rotation Sub Menu

Rotation:| Rotates the OSD menu.

Rotation Sub Menu

Rotation:| Performs factory reset.

EDID Write Protect Sub Menu

Write protect::| EDID write protect on/ off.

POS-Line IQ BLO

Note: All the Celeron mainboard drivers you can find at: https://www.distec.de/en/service/downloads/monitor-downloads/
Note: This POS-Line display is equipped with a battery. Please read the following note carefully:

• Unplug the power cable before exchanging the battery.
• There is a risk of explosion if the battery is not installed correctly.
• Replace the battery always with a battery of the same type.
• Recycle empty batteries with the free battery collection system. Please read the chapter “Disposal” in this document.

Passive cooling
POS-Line displays of the IQ BLO series (integrated PC) are designed for passive cooling.
Passively cooled monitors have a heat pipe that routes by which the heat of the processor to a heat sink on the back of the monitor.
Passively cooled devices have no moving parts.
PC specification
Please inform yourself current data sheet POS Line large about the details of the PC specification of the IQ BLO.
PC box connectors

Connectors of POS-Line IQ BLO series

Connecting to a network using a patch cable

Connecting to a PC using a cross-over cable

Connecting keyboard and mouse with USB cable

Connecting an external monitor with HDMI cable

Connecting active speakers with audio cable

Power on/off
After applying the supply voltage, the PC starts automatically. When the power supply is connected, the PC is switched on or off with the push button. During operation, the PC is shut down by briefly pressing the push button. Briefly pressing the push button switches the PC on.

BIOS settings
A Phoenix UEFI Flash BIOS is installed on the PC mainboard. To change BIOS settings press the ‘Enter’ key on your keyboard during the boot process of the PC.
Operating systems
An operating system is pre-installed if your POS-Line display has been ordered with this option. In this case, all mainboard drivers or touch drivers are installed.
Activating the operating system:

• Windows IoT: This OS is already activated. The license key sticker is located on the backside of the display.
• Windows 10: This OS is not activated. The license key sticker is added to the product documentation. After switching on the display for the first time Windows will prompt for the key

WebPoster

Connections and controls
WebPoster is POS-Line IQ BLO devices with special firmware, so the ports and operating in the „IQ Celeron“ must be observed. Connecting a mouse and keyboard is not supported with this firmware.
Functional description
The Industrial HTML Full HD Player is a complete solution for viewing Web pages. The website can be configured via a web interface. At the start of the device is automatically displayed.
Configuration of the media player on delivery (factory configuration)
This device is a LAN (Ethernet) enabled device. Please note that an incorrect network configuration of the device may affect the safe operation of the entire network and in the worst case a network, failure leads. To set up the device for a specific network, you need the key operating parameters of the network to be known. The POS Line WebPoster is shipped from the factory with the following configuration:

• DHCP: on
• IP-Address: 192.168.0.1*
• Netmask: 255.255.255.0
• Hostname: WebPoster-xx-xx-xx (the last 6 bytes of the MAC address of the device)
• Login Name: Artista
• Password: Artista

*** If no DHCP server is found, this IP address is assigned automatically.
Supported site formats**

• HTML5
• JavaScript

Software
On our website, you will find software and related documentation: https://www.distec.de/en/service/downloads/webposter-downloads/.
ADF: A program that simplifies the installation and configuration of HTML players. Connect any HTML player in the factory configuration to the network and start ADF. It displays all the HTML players in a list. Select the devices one by one and remove the network configuration.
Configuration of the media player
The configuration of the HTML player can work with any standard web browser (Firefox, Internet Explorer, Chrome, etc.) are performed. Connect the HTML player to a network and enter to establish the connection URL (eg. as IP address or network name) in the browser. Now open the WEB interface. If you are prompted for the password, enter the password (factory setting: Login name: Artista; password: Artista).
The layout of the web interface:

Configuration

Network Configuration:| The configuration of the network is the first step in setting up.
Submit Configuration:| With Submit Configuration the entries will be accepted.
Discard Changes:| With Discard Changes be deleted entries in the fields.
However, this has no influence on the current configuration.
Browser Settings:| The configuration of the Web page to display is the second step of the device.
Here the web page can be entered and a „Reload Interval (seconds)“ can be defined.
Submit Configuration:| With Submit Configuration the entries will be accepted.
Discard Changes:| With Discard Changes be deleted entries in the fields.
Change Password:| Here, the default password can be changed.
Information

System Information:| This page contains all details about the system, such as, for example, the software version.
If you contact our Support please add this page to your E-Mail to ensure a fast response.
Restart

Restart:| A restart of the media player.

Display of IP address and hostname

When booting the HTML player‘s current IP address and the hostname of the HTML player is displayed on the screen for about 5 seconds.

Maintenance

Systems with active cooling require cleaning of ventilation slots every 6 months. Systems with passive cooling must be cleaned every 12 months.

Warranty / Service

Warranty
Distec GmbH grants a manufacturer‘s warranty of two years from the date of delivery.
The rendering of warranty claims shall neither extend nor restart the warranty period.
During the warranty period, Distec shall repair product faults based on material or production defects. The warranty service is executed at Distec‘s discretion through repair, replacement of defective parts, or by exchanging a product for a product of equal quality without charging the customer for material or labor.
Warranty claims are only accepted if Distec receives the notification of a defective product within the warranty period and the product is presented to the Distec Service Centre together with all information as specified in the RMA process.
Warranty Exclusions and Limitations
This warranty does not apply to any defect for which Distec is not responsible and which includes, but is not limited to the following:

• Unauthorized opening or disassembling of the product
• Faulty maintenance by non-observation of maintenance instructions
• Inappropriate storage or cleaning of the product
• Unauthorized modification of the product
• Incorrect use or misuse
• Non-observation of operating and installation instructions
• Permanent display of fixed images (causing image retention or image sticking)
• Operating the product in conditions that exceed the limitations of the specification
• Use of inappropriate boxes, packaging, or modes of shipment
• Force majeure like fire, acts of war, acts of violence, chemical or biological impacts, lightning strikes, over-voltage or similar events
• Fault resulting from the use of software that was not originally supplied with the product or which is incorrectly installed
• Normal wear and tear and wearing parts (i.e. LCD panel)

Mechanical damages like scratches, pressure, or breakpoints are excluded from this warranty.
This warranty does not include accessory parts which are not an integral part of the product (such as boxes, or batteries).
Pixel errors only constitute a fault under the terms of this warranty if they deviate from the product specification (i.e. ISO 9241-307 pixel failure class II).
Display Quality – Prevention of after image burn-in effects

Afterimage burn-in means that an image or part of an image (i.e. logo) remains visible on the screen even if the image on the screen is changed. This should not occur if the LCD panel is operated in normal conditions with changing content. To prevent burn-in effects please follow the following guidelines.

• Do not display fixed patterns for an extended time period of more than 12 hours.
• Power-off the monitor for 4 hours after using it for 20 hours, and for 2 hours after using it for 12 hours.
• Use the power scheme and power management of the PC.
• Use plain-colored screen savers.
• Avoid patterns with a strong difference in brightness and contrast.
• Avoid gray colors.
• Change images and logos regularly. Show animated pictures for 60 seconds after 4 hours of operation.
• The best way to protect your display is to switch the monitor off when not in use or to use screen savers.

Non-observance of these guidelines may have effects on the warranty.
Warranty Processing
Group RMA process. In order to avoid unnecessary charges, it is important to adhere to the RMA regulations.
Products must be appropriately and professionally packed for a safe return to the Distec Service Centre. Products with panel sizes equal to or larger than 81 cm (32“) must be shipped on pallets in an upright position.
Distec does not assume liability for any customer data stored on products that are returned to Distec.
Limitations of Liability and Benefits
With this warranty declaration, Distec exclusively warranties that the product is free of material and manufacturing faults.
Distec does not issue any other warranty or similar statements other than this declaration.
This warranty does not impair or affect a buyer‘s statutory claim against the seller due to material damage. Such claims can be asserted instead of the warranty agreed to here at the buyer’s discretion.
Mandatory legal rights and mandatory claims under the German product liability remain unaffected.
Applicable Law and Place of Jurisdiction
The laws of the Federal Republic of Germany apply.
The place of jurisdiction is Munich.
Service addresses

Germany
Distec GmbH – Werk KIndel
Am Künkelhof 4
99820 Hörselberg-Hainich
+49 3 69 20 71 62-0
support@distec.de| Great Britain
Display Technology Ltd.
Osprey House, 1 Osprey Court,
Hinchingbrooke Business Park,
Huntingdon, Cambridgeshire, PE29 6FN
Tel +44 1480 411600
info@displaytechnology.co.uk| USA
Apollo Corp.
87 Raynor Avenue, Unit 1
Ronkonkoma NY 11779
+1 63 15 80-43 60
info@apollodisplays.com
---|---|---
Please go to the following web address for further information about our RMA regulations and RMA forms: http://www.distec.de/en/service

Disposal

Disposal of old devices
If the acquired Distec product is to be disposed of must be implemented into national law the Directive “2012/19 / EU”.
Disposal of batteries
Applicable in all countries of the EU and in countries with separate battery collection systems.
The Batteries in this product should not be disposed of with other household waste. The chemical symbol Pb, CD, or Hg indicates that the battery contains lead, cadmium, or mercury above the reference level in EC directive 2006/66/EG.
Batteries that are not disposed of correctly can cause harm to the environment and health.
Our environment is close to our hearts. Please help us to protect our environment and recycle empty batteries with the free battery collection system.

Declaration of Conformity

Declaration
Hereby the Distec GmbH declared that the unit EU is in compliance with the essential requirements and other relevant provisions of Directives 2014/30/EU, 2014/35/EU, and 2011/65/EU.
If you need a CE declaration of conformity, please request it from support on our website: https://www.distec.de/en/service/techni-cal-support/.

202204_Manual_POS_Line_BLO_EN.pdf

Documents / Resources

| DISTEC POS-Line BLO Series Industrial Grade Monitors [pdf] User Manual
POS-Line BLO Series, Industrial Grade Monitors, POS-Line BLO Series Industrial Grade Monitors
---|---

References

• Innovative TFT Displays and System Solutions
• Unser Service
• Innovative TFT Displays and System Solutions
• Monitor Downloads
• Downloads
• Unser Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>