ATEFA M-11 Dual 4K Front and 1080P Rear 4-Inch Car Camera User Manual

ATEFA M-11 Dual 4K Front and 1080P Rear 4-Inch Car Camera

Wiring and installation of rear camera

After determining the installation position, clean the oil stain and dust on the surface of the installation position. If the paste is not firm, the rear camera may fall off during driving .Tear off the release paper of double-sided adhesive tape stuck on the camera support, stick it at the confirmed installation position and press it firmly while confirming the image on the LCD, adjust the angle of the rear camera  recommended to install the waterproof rear camera outside the vehicle for better effect in order to drive safely please lay the wires and do not hinder the driving please do not cut off the rear drawing line for extension or modification, which may damage the machine or vehicle, and the rear camera will not work stably.

Reversing visual function

After the vehicle is in reverse gear, the recorder image will automatically switch to the pull-back camera and display the parking aid line. After exiting reverse gear  the equipment will return to the normal display state. Although the distance sensing guideline behind the vehicle is displayed in the image of the rear camera all dangerous obstacles cannot be displayed. Do not just look at the reversing image on the screen. Be sure to check the rear visually.

Installation of GPS module optional

• When the GPS module is installed in the vehicle, please try to install it on the instrument panel close to the front end of the windshield, and there shall be no metal cover on it, which will affect the reception of the GPS signal.

• After determining the installation position, clean the oil stain and dust on the surface of the installation position. If the paste is not firm, the GPS module may fall off during driving

• Tear off the release paper of double-sided adhesive tape stuck under GPS stick it at the confirmed installation position, and press it firmly note GPS can normally receive satellite signals and use them for positioning only when it is outdoors. In open areas, when the system is running normally  it can search and locate satellites in about 1 minute.

• Generally GPS positioning can be achieved only after receiving signals from at least four satellites.

• When this product is located in buildings, tunnels, or around tall obstacles, poor weather or dense obstacles where trees or buildings stand) may affect the reception of GPS satellite signals. At this time, the system will not provide you with positioning services for the time being.
  Download the track playback player

• You need to insert the GPS module into the corresponding GPS hole of the machine and insert the microSD card to format the memory card. At this time you are required to plug and unplug the memory card.

• Then it will generate an application gxplayer.exe in the memory card to download the application you need to install.

Double-click to enter the download interface, and the following progress bar appears.

After downloading  it will automatically enter the installation interface. Click next according to the prompt displayed on the page. After installation, the computer desktop will automatically generate an “gxplayer” application. Double click to enter the main interface of the player.

The playback software gxplayer is mainly used to check the GPS position, speed, and time of recorded video. There will be some noise when playing the recording with “GX player”. If you want to playback high-quality noiseless video, use another video player like KMPlayer (5) GPS data is included in the recorded video file. When playing the recorded video with GX player you can view the driving track by linking Google map. The interface of gxplayer is very simple. The upper left is the video viewing area, the middle is the video adjustment area, the lower part is the playback control area, and the upper right is the map display area.

Function Introduction

1. Power key
   Power On/ Off; In the shutdown state, short press the [power] key to turn on the power of the machine, and the machine will start working automatically. In the startup state, long press the [power] key for 3 seconds, and the dash cam will automatically save the video file and user settings then shut dow .Turn On/ Off Screen Backlight In any state, short press the power key to sleep and turn off the backlight; Short press the power key again to light up the screen

2. Up key
   On the home page interface, briefly press the [▲] up key, and the cursor will move to the left in the setting interface and playback interface, briefly press the [▲] up key, and the cursor will move up

3. OK key
   In any state, briefly press [OK] to confirm the currently selected function

4. Down key
   In the home page interface, briefly press the [▼] down key, and the cursor will move to the right
   In the setting interface and playback interface, briefly press the [▼] down key, and the cursor will move down

5. Mode key
   Short press the [Mode] key on the home page interface to switch the preview screen of front and rear cameras;
   There are 3 modes of cyclic switching: Front, Rear, or Front & Rear
   In the setting interface and playback interface, short the [mode] key to return to the main interface

6. Reset key
   
   Next to the power port on the side of the fuselage, if the recorder froze, briefly press the button in the hole to reconnect the power supply to restore normal main Interface

• Click the up and down buttons to move the cursor, select the recording icon click the OK button, the selected icon is green , indicating that the recording is in progress, there is a red dot flashing in the upper left corner and a video segment timing time display, click the OK button the icon is white indicating that the recording is stopped and there is no red dot and video segment timing time display in the upper left corner.

• Select the photo icon and click OK to capture the photo. There will be a click sound at the same time, which means that the capture of the picture was done. The capture of the photo is taken by the front and rear cameras at the same time

•  Select the lock icon and click OK to lock the current video file. White is the normal video file. Green means that the current video file has been locked.

• When the vibration sensitivity is turned on in the setting, the lock will be automatically locked in case of the vehicle collision. The lock icon of the current video file will turn green and will be locked only in the state of recording: In the setting interface and playback interface short the [mode] key to return to the main interface

• Reset key
  Next to the power port on the side of the fuselage, if the recorder froze, briefly press the button in the hole to reconnect the power supply to restore normal

• Main Interface Select the video playback icon and click OK to enter the video playback interface setting icon and click OK to enter the setting interface

• Select the recording icon and click OK. Green indicates that the recording is on  and white diagonal bar indicates that the recording is off.

Video Playback

In the main interface, click up and down to move the cursor to the video playback icon, press OK to enter the video playback preview menu, click up to page forward, click down to page backward, click OK to play the current video file, and click mode to return to the main interface

Set

On the main interface, click up and down to move the cursor in the red box to the setting icon, press OK to enter the setting menu, click up to move the option up, click down to move the option down, and click OK to confirm the currently selected option

• Video size: 1080p, 2k and 4K can be switched by setting; 4K by default
  Park video time lapse: You can set 1 second 1 frame and 1 second 4 frames, which are off by default

• This function can be realized only when a special time reduction video step-down cable 3-core is equipped and connected to the fuse box

• Open the time reduction monitoring and select 1s; After entering the parking monitoring mode, the time reduction video is recorded in the form of 1s one frame

• A video file is saved every 30 minutes or so to record the video efficiently and save memory space

•  Time lapse rec time: 2h, 8h, 12h and 24h can be set  If the miniature recording time is set to 8h, the parking monitoring function will be set by default after 8h This function can be realized only when a special miniature video step-down cable (3-core) is connected to the fuse box)

• Loop video
  Set the duration of video segmentation: 1min, 2min, and 5min; It is 2 minutes by default

• Exposure
  Seven modes of 3, 2, 1, 0, – 1, – 2, – 3 and can be set

• Parking mode
  On or Off  The default is off; The parking mode is turned on in the menu; When the recorder is turned off, it is vibrated; The recorder can sense it according to G-sensor, automatically start the machine and record for 20 seconds, and then turn it off; When the parking mode is not turned on, the recorder will not start when it is vibrated This file will be locked, and the locked image will be saved as a special file, which will not be overwritten circularly

• Gravity sensi ng according to the gravity sensing sensitivity, three modes can be set: low, medium, or high; Different sensitivities correspond to the Corresponding file locking sensitivity; The machine has a built-in collision sensor G-sensor. In case of a serious vehicle collision, the recorder will lock the current image data at the time of the accident, and the locked image will be saved as a special file, which will not be overwritten circularly

• Screen hibernation
  It can be set for 10 seconds, 30 seconds, 1 minute, and closed by default

• Language settings
  Click the language setting function to switch

• Video sound: on or off, on by default. Volume low, medium, high and low volume can be set.

• WiFi switch
  Turn WiFi On or Off, On by default.

• Light source frequency click in 50Hz and 60Hz are optional, and 50Hz by default

•  GPS switch: turn on or off the GPS function; It is turned on by default. After turning off the GPS function, the speed will no longer be displayed, and the track playback function will not be affected

• Time zone selection
  Select the correct time zone according to the current time zone. After GPS positioning, the time will be automatically corrected to the selected time zone

• Back mirror off by default. If on is selected, the rear preview is the original image. Note: it should be a mirror image when reversing

• Preview mode
  There are three modes: front recording, rear recording, and split-screen. This mode is the preview screen displayed on the boot screen. By default, the post recording preview screen is displayed on the boot screen date Click to set the date and time.

• Boot sound effect
  Turn On or Off the music of the dash cam, On by default

• Format
  Through this option, you can format the TF card  Please back up important data regularly before format; Formatting the MicroSD card will delete all files and cannot be recovered; Please operate carefully and make a backup; Please format the MicroSD card regularly; If it is used for a long time, the recorder will stop recording because the locked file will not record circularly, resulting in insufficient capacity of the recorder; It is recommended to format once every 1-2 weeks

• Restore factory settings
  Click restore factory settings to prompt whether to restore factory settings, confirm or cancel

• Device information
  Click to view the information related to the system version number

• WiFi information
  Click to view the QR code downloaded from the mobile terminal, display the local WiFi name and WiFi password, and facilitate the mobile terminal app to connect WiFi

Mobile APP Download

Enter the settings in the dash cam, click the general settings, turn On the WiFi, then install the app to your phone scan the following QR code to download or Find the “Road cam” from app store.

If you select WiFi information, the WiFi name. Random WiFi name can be changed by the user after connecting to the mobile app WiFi password 12345678can be changed by the user after connecting to the mobile app by default. The mobile terminal downloads app road cam by scanning the QR code, and opens the WiFi connection of the mobile terminal to the machine hotspot.

Select WiFi information, the WiFi name .Random WiFi name can be changed by the user after connecting to the mobile app WiFi password 12345678 can be changed by the user after connecting to the mobile app by default) and QR code will appear. Use the mobile phone to scan the QR code and download roadcam.

Matters Needing Attention

Disclaimer

• The tachograph is a recording device for images, sounds and other related information during vehicle driving. In case of an accident, it is only used as an auxiliary reference the machine must be in normal video recording working state before recording video files. However, the image will be damaged or lost under the following circumstances during video recording, pulling out the microSD card will cause the last video file to be damaged or lost.
• Illegal power failure in the video will lead to damage or loss of the last video file.
• Damage or loss of video files caused by destructive collision of the machine during video recording.
• The memory card is loose due to excessive collision during video recording, which will damage the video file or cause the loss of video file.
• Do not squeeze the dash cam at will. If the dash cam is abnormal, briefly press the reset key. On the back of the fuselage, the dash cam will be powered off and restarted.
• When the machine is installed correctly, the machine starts to enter the recording state, and the recording indicator flashes. Please check whether the picture on the display screen is normal.
• If the display screen is inverted, please contact us in time  please format the microSD card in the machine menu for the first time.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>