PERFECTPRO Rock Box 2 Workplace Radio Instruction Manual

Workplace Radio
Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Clean only with a dry cloth.

6. Do not block any ventilation openings. Install in accordance with the instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.

9. Protect the power cord from being walked on or pinched particularly at the plug, convenience receptacles, and the point where they exit from the apparatus.

10. Only use attachments/accessories specified by the manufacturer.

11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/
    apparatus combination to avoid injury from tip-over.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required if the apparatus has been damaged in any, such as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

15. Do not remove the cover; there are no user-serviceable parts inside.

16. No naked flame sources shall be placed on the apparatus.

17. For outdoor use, to avoid electric shock, use the battery only during a rainy day or the weather is wet. To prevent electric shock, if the radio has been exposed to rain or water, the power supply cord and plug must be completely dried before plugging into the main socket outlet.

18. The power plug should be close to the apparatus, and easy to be approached during an emergency, to disconnect the power from the apparatus, just unplug the power plug from the AC power slot.

19. The marking information is located at the bottom of the apparatus.

20. This apparatus is provided with protection against splashing water (IP65).

21. In case of malfunction due to electrostatic discharge or fast transient (burst), remove and reconnect the power supply.

22. To prevent possible hearing damage, do not listen to high volume levels for long periods.

Front View

1. On/Off (Standby) button

2. Source button

3. Menu button

4. Loudness button

5. Info button

6. Preset 1 -10 buttons
   Top View
   

7. Volume / Tone Control knob
   

8. Tuning / Seek Station / Time Set
   Side View
   

9. Aux-in socket
   Back View
   

10. Rubber antenna
    

11. Battery cover fixtures
    

12. Battery compartment
    

13. Power cord
    

14. USB socket
    

**POWER SUPPLY

**

AC operation
Before plugging the AC power cord into the AC socket, be sure the voltage is correct.
If you have batteries in the radio and use the AC power supply, the batteries will automatically be disconnected.
AC power cord storage is designed to store the cord when the radio is not in use.

Note:  In order to disconnect the unit from the mains completely, the AC plug should be removed from the mains socket completely.

Battery operation

1. To open the battery compartment, first, turn the battery cover fixtures anti-clockwise to loosen and pull down the battery cover.

2. Insert a 6 x C size (UM-2) battery with the correct polarity into the compartment. Close the battery covers and fasten the fixtures by turning clockwise. Close well to prevent
   moist or dust from entering the compartment.

3. If the unit is not to be used for any extended period of time, it is recommended that the batteries are removed from the radio.
   The approximate power level of the batteries is displayed in the LCD display of the radio.
   When the power level is very low the indication “Battery Low!” appears and the battery symbol flashes on the display. The batteries should then be replaced soon to continue the normal operation of the radio.

Notes:
The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.
Do not expose the batteries to excessive heat such as sunshine, fire, or the like.
Batteries should not be disposed of by incineration and with household waste.
Disposable batteries should be taken to a suitable recycling center if possible.

USING THE RADIO FOR THE FIRST TIME

1. Place the radio on a flat surface.

2. Carefully extend the antenna located on the top of the radio. Adjust the antenna so it is vertically extending above the radio.

3. Plugging the AC power cord into the AC socket. The radio will start up and the display will show “WELCOME TO DIGITAL RADIO” for a few seconds. Then the
   radio will automatically perform an auto-scan of the Band III DAB channels and the FM band, the display will show the “ATS setting”.

4. When the scan is completed, the 10 strongest FM stations will be stored as presets.
   The radio will switch to standby with the updated clock and date showing on the display.

5. If no signals are found, the clock will not be updated. It may be necessary to relocate the radio to a position giving better reception.

Additional metal telescopic antenna
You can use this as an alternative antenna for your radio in areas or locations where the radio signal (FM/DAB/DAB+) is weak to very weak.
ATTENTION; the standard antenna on the radio is flexible, this antenna is not flexible.
Installing: Carefully screw off the standard flexible antenna. First, carefully loosen the antenna with an open-end-wrench (size 14) – turn counterclockwise.
Carefully screw on the metal telescopic antenna and softly tighten it with an open-end wrench key (size 14) – turn clockwise

ATTENTION: do not use too much force when fixing the antennas as this can damage the screw thread of the antennas or make it break off.

DAB MODE

Operating the radio – DAB

1. Carefully extend the antenna. Press the On/Off button to switch on the radio.

2. If this is the first time to switch on, the radio will be in DAB mode.

3. The first station (in numeric-alpha order 0…9…A…Z) in the list of stations found will be played. The display will show the station name.
   If the radio has been used before, the last used station will be selected.

4. If no signals are detected, “No stations available” will be displayed. It may be necessary to relocate the radio to a position giving better reception.
   You should then carry out an auto scan to find stations, please refer to the section “Find new stations – DAB”.

Selecting a station – DAB

1. Press the On/Off button to switch on the radio. The display will show “Now tuning” for a few seconds.
2. The display shows the name of the radio station currently selected.
3. Rotate the Tuning knob to scroll through the list of available stations.
4. When the desired station name appears on the display, press the Tuning knob to select the station. The display will show “Now tuning” while the radio finds the new station.

Note:  If after selecting a station the display shows “No stations available”, it may be necessary to relocate the radio to a position giving better reception.

Secondary services – DAB

1. Certain radio stations have one or more secondary services associated with them.
   If a station has a secondary service associated with it, then the secondary service will appear immediately after the primary service as you turn the Tuning knob.

2. Press the Tuning knob to select the secondary service.
   Most of the secondary services do not broadcast continually and if the selected service is not available, the radio will re-tune to the associated primary service.

Display modes – DAB

In DAB mode, the radio can display a range of information on the display.

1. Press the Info button to cycle through the various modes.
   a. Scrolling text
   b. Signal strength
   c. Program type
   d. Multiplex name
   e. Channel & frequency
   f. Bit rate & audio type
   g. Time & date| Displays scrolling text messages such as artist/track name, phone number, etc.
   Displays the signal strength of radio reception. The clear unfilled rectangle indicates the minimum signal level required for satisfactory reception.
   Displays the type of station being listened to e.g. Pop, Classic, News, etc.
   Displays the name of the multiplex to which the current station belongs.
   Displays channel number and frequency for the currently tuned DAB station.
   Displays the digital audio bit rate.
   Displays the current time (24-hour clock) and date.
   ---|---

Finding new stations – DAB
From time to time, new stations may become available. You may proceed to find new stations as follows:-

1. Press the Menu button, and “Full scan” shows on the display.
2. Press the Tuning knob, the radio will perform a scan of the Band III DAB channels.

As new stations are found, the station counter on the right-hand side of the display will increase and stations will be added to the list.

Manual tuning – DAB
Manual tuning allows you to tune the radio directly to various DAB Band III channels.

1. Press the Menu button, the display shows “Full scan”.

2. Rotate the Tuning knob until the display shows “Manual tune”. Press the Tuning knob.

3. Rotate the Tuning knob to select the desired DAB channel. Press the Tuning knob to tune the chosen frequency.

4. The signal strength display with an open bar shows the minimum signal strength needed for good DAB reception. The signal strength bars will go up or down showing
   the changing signal strength as you adjust the antenna or the radio position.

5. When a DAB signal is found, the display will show the name of the station. Any new radio stations found will be added to the list stored in the radio.

6. Press the Tuning knob to return to normal DAB service.

Dynamic Range Control (DRC) settings – DAB

DRC can make quieter sounds easier to hear when the radio is used in a noisy environment.

1. In DAB mode, press the Menu button, and the display shows “Full scan”.
2. Rotate the Tuning knob until the display shows “DRC value”. Press the Tuning knob.
3. Rotate the Tuning knob to select the required DRC setting (default is Off).
   DRC Off| DRC is switched off. Broadcast DRC will be ignored.
   ---|---
   DRC Low| DRC level is set to low which is sent by the broadcaster.
   DRC High| DRC is set as sent by the broadcaster.
4. Press the Tuning knob to confirm the setting. The display will return to a normal radio display.

Note:  Not all DAB broadcasts use the DRC function. If the broadcast does not provide DRC information, the DRC setting in the radio will have no effect.

Prune stations – DAB

If you move to a different part of the country, some of the stations which were listed may no longer be available. Also, from time to time, some DAB services may stop broadcasting or may change location or frequency. The Prune stations function will delete the unavailable DAB stations from your station list.

1. In DAB mode, press the Menu button, and the display shows “Full scan”.

2. Rotate the Tuning knob until the display shows “Prune”.

3. Press the Tuning knob to enter the setting.

4. Rotate the Tuning knob to select between “Yes” or “No” (default is No).
   Select “Yes” to enable this function if required, otherwise, select “No”.

5. Press the Tuning knob to confirm your setting. The display will return to a normal radio display.

Note:  If you have moved the radio to a different part of the country, you should also carry out a search for new stations (please see the section “Finding new stations – DAB”).

FM MODE

Operating the radio – FM seek station

1. Press the On/Off button to turn on the radio.
2. Select the FM waveband by pressing the Source button.
3. If this is the first time switching to FM mode, the station in preset 1 will be played. If the radio has been used before, the last listened station will be played.
4. To seek a station, press the Tuning knob. The scan stops automatically when it finds a station of sufficient strength.
5. After a few seconds, the display will update and show the station name if RDS information is being received.
6. To find other stations, press the Tuning knob again.
7.  To seek a station in an opposite direction, rotate the Tuning knob clockwise (to scan from low frequency to high frequency) or rotate it anti-clockwise (to scan from high frequency to low frequency), and press the Tuning knob.
8. When the waveband end is reached, the radio will recommence tuning from the opposite waveband end.

Manual tuning – FM

1. Press the On/Off button to turn on the radio.

2. Select the FM band by pressing the Source button.

3. Rotate the Tuning knob to reach the required FM station. The radio will change the frequency in steps of 50 kHz.

4. Rotate the rubber antenna to get the best reception. If the radio is tuned to a station of sufficient signal strength with RDS information present, the display may change
   to show the station name.

5. When the waveband end is reached, the radio will recommence tuning from the opposite waveband end.

RDS station service – FM
RDS (Radio Data System) is an information system in which inaudible digital information is transmitted in addition to the normal FM radio program. When the radio is receiving an RDS station and the reception strength is sufficient, the station name will appear on the display. It may take some time before the RDS information is available.

Calling up RDS information

1. When you are listening to an FM station with an RDS system, repeatedly press the Info button to cycle through the information. This will only function if the reception level is sufficient and clear.

a. Radio text (RT)
b. Program type (PTY)
c. Frequency
d. Time & date
e. Signal level| Displays the message about the station being listened to as ticker text.
Displays the type of station being listened to, e.g.
Pop, Classic, News, etc.
Displays the frequency of the station being listened to.
Displays the current time (24-hour clock) and date.
Displays the signal strength.
---|---

Scan sensitivity setting – FM
The radio will normally scan all stations from FM broadcasts including the weaker signals. However, you may wish the Auto-scan to find only those stations with strong enough signals to give good reception.

1. Press the On/Off button to turn on the radio.

2. Select the FM band by pressing the Source button.

3. Press the Menu button, the display shows “Scan setting”.

4. Press the Tuning knob.

5. Rotate the Tuning knob to select between “All stations” or “Strong station” (default is All stations).
   The “Strong station” option will allow the radio to find strong signals only when scanning.

6. Press the Tuning knob to confirm your setting. The display will return to a normal radio display.

PRESET STATIONS

Storing preset stations
There are 20 memory presets in the radio, 10 for DAB and 10 for FM. Presets are remembered by the radio in the event of a power failure.

1. Press the On/Off button to turn on the radio.
2. Press the Source button to select the desired waveband.
3. Tune to the required station.
4. Press and hold the required Preset button until the radio beeps and shows for example “Preset 01 Saved”.
5. Repeat steps 3 and 4 for the remaining presets.
6. Stations stored in the preset memories can be overwritten by following the above procedure.

Recalling preset stations

1. Press the On/Off button to turn on the radio.
2. Press the Source button to select the desired waveband.
3. Briefly Press the required Preset button, and the display will show for example “Preset
   01 Loaded” for a few seconds and the radio frequency.

BLUETOOTH MODE

Pairing Bluetooth with your mobile phone

1. Press the On/Off button to turn on the radio.
2. Select Bluetooth mode by pressing the Source button.
3. The LCD display will show “Not connected” when the radio is not yet paired with your mobile phone.
4. In your mobile phone open the Setting menu and select Bluetooth, then select “PP RockBox 2” in the Bluetooth devices list of your mobile phone (Bluetooth pairing instructions may vary per type of mobile phone, please check your mobile phone manual).
5. When Bluetooth pairing is successful, the LCD display will show “BT Connected” in the 1st line, and your mobile’s name in the 2nd line for about 2 seconds.
6. Finally, the LCD display will show the connected mobile phone’s name in the 1st line to indicate the connected device to the radio.

Playing music from your mobile phone

1. Press the On/Off button to turn on the radio.
2. Select Bluetooth mode by pressing the Source button.
3. Start playing music by using the media players in the paired mobile phone.
4. Playback can be controlled from the mobile phone or by pressing the,   and buttons (preset buttons 3, 4, and 5) on the radio.
5. After the music playback starts, the name of the song will be displayed on the LCD.

Display modes – Bluetooth

In Bluetooth mode, the radio can display a range of information of the current playing music on the display. Press the Info button to cycle through the various types.

a. Title
b. Artist
c. Album
d. Status
e. Music info
f. Time & date| Displays scrolling song’s name of the current playback music.
Displays the artist’s name of the current playback music.
Displays the album name of current playback music.
Displays the playback status. E.g. playing, stopped.
Displays the music format and sampling rate of the current playing song. For E.g. “AAC” is the format of the song; “44100Hz” is the sampling frequency of the song.
Displays the current time and date.
---|---

Device List – Connect to the paired device
In the radio, you can select the Bluetooth device from the Device list to connect again.
The device names would be shown if the name of the Bluetooth devices were configured in the mobile devices. Please refer to the user manual of your mobile device for the
configurations.

The Device List can be checked as below:

1. In Bluetooth mode, press the Menu button to enter the system setting.
2. Rotate the Tuning knob until the “Device list” is displayed; press the TUNING knob to select the setting.
3. Rotate the Tuning knob to view the name of the devices.
4. Press the Tuning knob to start Bluetooth reconnection. The speaker will automatically connect to this selected mobile device.

Note: There can be up to 8 device names stored in the Device list memory. If you store more than 8 mobile devices in the Device list memory, the earliest paired device name
will be erased.
Note: If you have ever deleted the “PP RockBox 2” from your connected mobile phone device, the auto reconnection will be unsuccessful.

Restart Bluetooth pairing
The Bluetooth function can be set to operate in different ways as below:

1. In Bluetooth mode, press the Menu button to enter the system setting.
2. Rotate the Tuning knob to select the “Disconnect BT” option, and press the Tuning knob to select the setting.
3. The LCD display will show “Please wait” for a few seconds in order to disconnect the current connection with the mobile phone device.
4. The LCD display will show “Not connected” and the radio’s Bluetooth is free for any mobile phone device connection as it is in the discoverable mode now.

Note:  “Disconnect BT” is the option that forces the Bluetooth of this radio to disconnect from your mobile phone and enter the “discoverable mode”. This is the way to allow
Bluetooth pairing to another device. If no new device is paired, the Bluetooth will automatically try to connect to the last device when it is switched off and on again.

The Auto-Power management function will be activated in Bluetooth mode. If there is no signal* for a period of over 15 minutes, the radio will automatically switch to standby mode. Pressing the On/Off button will wake up the unit.

• Also when the incoming signal from the external device is too low and cannot be detected for a period of over 15 minutes by the Auto-Power management, the radio will
  switch to standby mode.

To prevent this raise the output level on the external device enough to be detected.

AUX IN MODE

A 3.5mm stereo Aux In socket is provided on the side behind the rubber cover, for connecting an external audio device such as an MP3 player or CD player (not included with
this radio).

1. Connect an audio source to the Aux In socket.
2. Press the Source button to select AUX input. The display will show “AUX IN”.
3. Play the external player.
4. Adjust the volume of both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moisture or dust from entering the sockets and radio.

Notes:  Never use the AUX-IN socket in rainy or moist conditions to prevent moisture from entering the radio. Keep the rubber cover closed under these conditions.

The Auto-Power management function will be activated in AUX mode. If there is no signal from the AUX input jack for a period of over 15 minutes, the unit will automatically
switch to standby mode. The operation indicator and the LCD will go off in such a case.

Pressing the On/Standby button will wake up the unit.

SETTING THE CLOCK

The clock can only be set when the radio is in standby mode. If no buttons are pressed for 5 seconds, the radio will exit the clock setup and the setting is canceled.

1. Press and hold the Time Set knob for 12 seconds until the hour digits flash on the display.
2. Rotate the Time Set knob to set the hour.
3. Press the Time Set knob to confirm, the minute digits flash.
4. Rotate the Time Set knob to set the minute.
5. Press the Time Set knob to confirm, the day flashes on the display.
6. Rotate the Time Set knob to set the current day.
7. Press the Time Set knob to confirm, that the month flashes.
8. Rotate the Time Set knob to set the current month.
9. Press the Time Set knob to confirm, the year will then flash on the display.
10. Rotate the Time Set knob to set the current year.
11. Press the Time Set knob to confirm, the “SYNC LOCK ON” flashes.
12. Rotary the Time Set knob to select “SYNC LOCK ON” or “SYNC LOCK OFF”.
13. Press the Time Set knob to confirm and finish the clock setting.

RDS time synchronisation
If “SYNC LOCK ON” is selected, the symbol “  ” will show on the clock display.
Some RDS stations transmit a time signal. If reception is good and you have selected the “SYNC LOCK ON” option during the time setting, the time will be automatically updated (“  ” flashes on the display). Time synchronization can take several minutes. The automatic time setting is always activated when the radio is switched from standby to FM broadcasting and receives an RDS station.

LOUDNESS
The Loudness function enables to get compensation on lower and higher frequencies.
The effect will be more audible when the radio is at a lower volume level (Dynamic Loudness).

1. Press the Loudness button to enable the loudness, the display shows “Loudness On”.
2. Press the Loudness button again to disable the loudness, the display shows “Loudness Off”.

LANGUAGE SETTING
The radio can be configured to a different language.

1. Press the On/Off button to turn on the radio.
2. Press the Menu button, and then rotate the Tuning knob until the display shows “System”.
3.  Press the Tuning knob; rotate the Tuning knob until the display shows “Language”.
4.  Press the Tuning knob to enter the language adjustment menu.
5.  Rotate the Tuning knob until the desired language appears on the display (the default is English).
6. Press the Tuning knob to confirm your choice. The display will change to the chosen language.

SOFTWARE VERSION

The software display cannot be altered and is just for your reference. You can only view the software version in DAB and FM mode.

1. Press the On/Off button to switch on the radio.
2. Press the Source button to select FM or DAB mode.
3. Press the Menu button until the display shows “Full Scan” , and then rotate the Tuning knob until the display shows “System”.
4. Press the Tuning knob; rotate the Tuning knob until the display shows “SW version”.
5. Press the Tuning knob to view the software version.
6. Press the Tuning knob again to return to the normal radio display.

Notes:  The USB socket inside the battery compartment is for upgrading the software of the device.

SYSTEM RESET

If the radio fails to operate correctly, or some digits on the display are missing or incomplete, carry out the following procedure.

1. Press the On/Off button to switch on the radio.

2. Press the Menu button,

3. Rotate the Tuning knob until the display shows “System”. Press the Tuning knob.

4. Rotate the Tuning knob until the display shows “Factory reset”. Press the Tuning knob.

5. Rotate the Tuning knob to select between “Yes” or “No”.
   Select “Yes” if you wish to reset the radio, otherwise, select “No”.

6. Press the Tuning knob to cause the factory to reset.

7. A full reset will be performed. All presets and the station list will be erased. All settings will be set to the default values.

The display will show “WELCOME TO DIGITAL RADIO” for a few seconds, and then the radio will automatically perform an auto-scan of the Band III DAB channels and
the FM band, the display will show “ATS setting”.

In case of malfunction due to electrostatic discharge; reset the product as above to resume normal operation. If you are not able to perform the reset operation as above, remove and reconnect the power supply.

BACKLIGHT

LCD backlight configuration

1. Press the On/Off button to turn on the radio.
2. Press the Menu button, and then rotate the Tuning knob until the display shows “System”.
3. Press the Tuning knob; rotate the Tuning knob until the display shows “LCD backlight”.
4. Press the Tuning knob to enter the LCD backlight adjustment menu.
5. Rotate the Tuning knob to select “on” in order to keep the backlight always lightened when the radio is turned on with an AC power supply;
6. Or rotate the Tuning knob to select “off” (by default) so that the backlight will be lightened for about 10 seconds whenever a button is pressed with an AC power supply.
7. Press the Tuning knob to confirm your choice.

Note:  The LCD backlight option “on” is only functional when the radio is powered by an AC power supply. When the radio is powered by the battery power supply, the LCD backlight is switched to option “off” – 10 seconds lightened when a button is pressed. When the radio is connected to mains AC power again, the last user setting will be applied again.

RADIO NAME OPTION

This radio supports customization of the radio’s name. If the radio has been named, the name of the radio will be shown when the radio is turned on and when the radio is turned off.

1. Press the On/Off button to turn on the radio.

2. Press the Menu button, and then rotate the Tuning knob until the display shows “System”.

3. Press the Tuning knob; rotate the Tuning knob until the display shows “Name”.
   Press the Tuning knob.

4. Rotate the Tuning knob to select the letters. The maximum length of the new name is 16 letters long.

5. Press the Tuning knob to confirm the current selection. By pressing this Tuning knob, the cursor will be moved to the next position for selection.

6. Press the P3 or P4 button to move the cursor to left or right.

7. Repeat step 4 to step 6 to edit the new radio name.

8. To complete editing the new radio name, you can either edit all the 16 letters or press the Menu button.

9. When finishing editing the radio name, the LCD will display “Confirm changes” in the first line, and display “OK” to save the changes or “Cancel” to discard the changes.

10. To confirm the changes, rotate the Tuning knob until “OK”, and then press the Tuning knob to exit. After this action, the radio will save the new name.

11. To cancel the changes, rotate the Tuning knob until “Cancel”, and then press the Tuning knob to exit. After this action, the radio will discard the changes and keep the current radio name for display.

12. When the next time the radio is turned on, the LCD will show “Welcome” in the first line and the new name in the second line.

13. When the radio is turned off, the LCD will show “Goodbye” in the first line and the new name in the second line.

Notes:
– In the name menu, when there is no operation of the panel buttons for more than 20 seconds during editing, the radio will automatically exit the name function without
saving any of the changes.
– The default radio name is empty. The new edited name will be lost and go back to default (no name) after executing a factory reset in the menu.
– The radio supports a maximum of 16 letters as the name of the radio.

TONE

The Tone function enables the user to adjust the lower and higher sound frequencies.

1. Press the On/Off button to turn on the radio.
2. Press and hold the Volume knob for about 3 seconds, the display shows “BASS 0”.
3. Rotate the Volume knob to set the desired Bass level.
4. Press the Volume knob to confirm, the display shows “TREBLE 0”.
5. Rotate the Volume knob to set the desired Treble level.
6. Press the Volume knob to confirm and return to the normal display.

ATP PASSCODE

This radio is equipped with an Anti-Theft-Protection system (ATP system). When the ATP system is enabled, a passcode is required for turning on the radio.

1. Press the On/Off button to turn on the radio.
2. Press the Menu button.
3. The display shows “System”.
4. Rotate the Tuning knob until the display shows “Passcode”. Press the Tuning knob. “Enable” or “Disable” will be displayed, to enable ATP, turn and press the Tuning knob to select “Enable”.
5. “Change Passcode” will be displayed, enter a 4-digits numeric passcode by pressing the preset buttons (1-10)
6. “Confirm Passcode” will be displayed. Enter a second time the same passcode to re-confirm.
7. To disable the passcode, select “Disable” as previously shown. And re-enter the previous passcode to disable the lock.

When ATP is enabled, and if the wrong passcode is entered for three times, a timer will be activated. The next attempt will be possible only after the timer has elapsed. The timer period will be increased with further wrong passcodes.

WARNING:  If you choose to activate the passcode, please note your passcode somewhere safe as a memory backup in case you should forget it. This as there is no way to reset the radio should the passcode be forgotten!

WARRANTY

This radio has a 2-year limited warranty.
WARNING! Warranty becomes void once the radio cabinet has been opened or any modifications or alterations to the radio have been made!

The terms of the warranty of this radio do not cover the following:
– Damage caused by misuse, abuse, neglect, alterations, accidents, or unauthorized repair.
– Normal wear and tear.
– Breaking or bending of the metal telescopic antenna.

SPECIFICATIONS

Power requirements
Mains
AC230V 50Hz~
Batteries
6 x C size (UM-2)

Frequency coverage
DAB+ / DAB
174.928 – 239.200 MHz
FM 87.5 – 108 MHz

Bluetooth
Version 3.0 Supports Bluetooth profiles A2DP, AVRCP, and HFP

Circuit features

Loudspeaker
1 x Ø4 inch
Output power
1 x 7.5W
Aux In socket
Ø3.5 mm

Environmental note:

This product has been made from high-quality parts and materials which can be reused and recycled.
Therefore, do not throw the product away with normal household waste at the end of its life. Take it to a collection point for recycling electrical and electronic devices. This is indicated by this symbol on the product, in the operating manual, and on the packaging.
Please find out about collection points operated by your local authority.
Help protect the environment by recycling used products.

Perfect B.V.
Everdenberg 9A
4902TT Oosterhout
The Netherlands
www. perfect.eu

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>