DS18 BASS68 6×8 Inch Under Seat Active Subwoofer Owner’s Manual

: June 5, 2024
: DS18

Table of Contents

INTRODUCTION
WARRANTY
SPECIFICATIONS
INSTALLATION
CONNECTIONS
CONNECTIONS
INPUT/POWER CONNECTOR
SWITCH SETTINGS
Documents / Resources

DS18 BASS68 6×8 Inch Under Seat Active Subwoofer Owner’s Manual

INTRODUCTION

Thank you for your DS18 SQBASS68 purchase.
In order to enjoy the best service from us please keep your original invoice well and complete the warranty card. If you have any questions, or need technical support please email us at: customerservice@ds18.com

WARNING

Do not operate any function that takes your attention away from driving your vehicle safely.
Any function that requires your prolonged attention should only be performed after coming to a complete stop.
Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident

Keep the volume at a level where you can still hear outside noises while driving.
excessive volume levels that obscure sounds such as emergency vehicle sirens or road arning signals (train crossing, etc) can be dengerous and may result in an accident. Listening at loud volume levels in a car may also cause hearing damage.

Do not disassemble or alter. Doing so may result in a accident, fire or electrilc shock.

Use this product for mobile 12V applications.

Use the correct ampere rating when replacing fuses. Failure to do so may resultin a fire or electrilc shock.
Do not block vents or radiator panels. Doing so may cause heat to build up insideand may result in fire.
Make the correct connections. Failure to make the propper connection may result in fire and/or product damage.

Use only in vehicles with a 12V Negative Ground. Failure to do so may result in fire and/or product damage. (Check with your dealer if you are not sure)

Before wiring, disconnect the cable from the negative battery terminal.

Do not allow cables to become entangled in surrounding objects. Arrange wiring cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel.

Do not splice into electrical cables. Never cut away cable insulation to supply power to other equipment.
Doing so will exceed the current carrying capacity of the wire and result in fire or elictrical shock.

Do not damage pipe or wiring when drilling holes. When drilling holes in the chassis for instalation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

Do not use bolts or nuts in the brake or the steering system o make ground connections.
Keep small objects such as bolts or screws out of the reach of children. Swalloing them may result in serious injury. If swallowed, consult a physician immediately.

CAUTION

Stop use immediately if a problems appears.
Failure to do so may cause personal injury or damage to the product.
Return it to your authorized dealer or the nearest Service Center for repairing.

Have the wiring and installation done by experts.
The wiring and installation of this unit requires special technical skills and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

Use specified accessory parts and install then securely. Be sure to use only the specified accesory parts. The use of other than the designated parts may damage the unit internally or may not securely install the unit in place.

Arrange the wiring so it’s not crimped or pinched by a sharp metal edge. Route the cables and wiring passes (like the seat rails) or sharp or pointed edges. This will prevent pinching and damage to the wiring. If wire passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.

Do not install in locations with high moisture or dust. Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrate the unit may result in product failure.

WARRANTY

If your amplifier require service: Please consult the dealer from which it was purchased, or contact DS18 CAR AUDIO Local Dealer. Do not attempt to return your amplifier directly to us without first calling for a Return Authorization Number.

Units received without any accompanying Return Authorization Number will be processed more slowly. Additionally, you must include a copy of your purchase receipt from an authorized dealer for consideration of in-warranty service; otherwise repair charges will apply. Units received without a receipt will be held for 30 days, allowing us time to contact you and obtain a copy of the receipt. After 30 days, all units will be returned.

SPECIFICATIONS

GENERAL SPECIFICATIONS

Speaker Type / Size 6×8″
Total RMS Power Handling 150W
Total MAX Power Handling 600W
Sensitivity (1w/1m) 77 dB
Frequency Response 42 Hz-400 Hz

SPEAKER SPECIFICATIONS

Voice Coil Diameter 1.2″ / 30.6mm
Cone Material Polypropylene
Surround Material Rubber
Basket Material Steel
Magnet Material Ferrite
Body / Housing Material Aluminum

AMPLIFIER SPECIFICATIONS

Amplifier Class Digital
Amplifier Type Subwoofer Monoblock
Number of Channels 1Ch
Minimum Impedance 2ohm
Signal to Noise Ratio >80dB
Total Harmonic Distortion (THD) <0.5%
Low Level Input Range 0.1-5 Volts
High Level Input 0.5-10 Volts
Selectable X-Over LPF Fixed
X-Over Filter Range 50-150Hz
Infrasonic Filter 30Hz Fixed
Phase Selector 0-180°
Led Indicator Power/Protect
Power Input Terminal Size 12Ga Wired
Fuse Size 15A
Remote Level Control Yes, Included
Thermal Protection Yes
Over-Load Protection Yes
DC Output Protection Yes
Short Circuit Output Protection Yes
Voltage Input Protection Yes

EXTRA FEATURES

Remote Knob Cable Length 16ft / 5m
Remote Knob Adjust Range 0-30dB
Auto Turn-On Yes, Signal Sensing

MEASUREMENTS

Overall Height 2.95″ / 75mm
Overall Width 7.67″ / 195mm
Overall Length 10.2″ / 260mm

INSTALLATION

Cautions on connections terminal/parts. Keep electrically conductive objects away from the units terminals/parts (power terminals, fuses,speaker input terminals, RCA connectors, etc) Doing so prevents a possible short circuit and damage to the unit.

Mounting: Attach the including mounting brackets to the SQBASS68 with the supplied screws. (at Fig. 1) Once the brackets are mounted to the SQBASS68 place the subwoofer in the desired location within the vehicle. Before securing with screws, check to make sure all screws can affix to a structurally solid surface while avoiding vehicle wiring,components, etc. (at Fig. 2)
INSTALLATION

Mounting Bracket
Bracket Screws
Attachment Method Of Remote Bass Level Knob

NOTE:
For securing the mounting brackets to the vehicle, it may be necessary to use longer screws (not included) to securely connect the ground lead, use an already installed screw on the metal part of the vehicle. (mark this as a good ground by checking continuity to the battery (-) terminal. To avoid and reduce as much noise as possible, please connect all equipment to the same ground point.

Accesory List

1 x Insert Power Cable
1 x Remote Control
4 x Bracket
8 x Screws
8 x Brackets Screws
2 x Magic tape (30x100mm)

CONNECTIONS

MAKING CONNECTIONS:

Turn every audio component OFF
Connect the red battery lead from the amp to the positive (+) terminal of the vehicle’s battery
Locate the unit and rout the leads at least 10 cm (3-15/16”) away from the vehicle’s harness
Keep the battery power leads as far from other leads as possible
Connect the ground lead securely to a bare metal spot from the vehicle’s chasis (remove any paint or grease if necessary)

NOTE: Head unit and RCA extension cables are sold separately

F: Head Unit
G: RCA Extension Cable
H: Speaker Level from the Radio
1: Main Connector
2: RCA Input Jack
3: Fuse (15A) Use only the correct ampare rating when replacing fuses. Failure to do so may result in fire or electric shock
4: Input/Power Wire Harness
5: Speaker input lead system These input leads are ment to be used with head units not equipped with preamp outputs. When not using the RCA Line Input connectors, you should connect these wires to the speaker output leads of your head unit.

CONNECTIONS

INPUT/POWER CONNECTOR

6: Battery Lead (RED) Connect battery lead directly to battery (+) terminal Be sure to add a 15A fuse (sold Separately) as close as possible to the battery (+) terminal
7: Remote Turn-On lead (Blue/White) Connect this lead to the remote turn on (positive trigger, 12V ONLY) lead of your head unit
8: Ground Lead (Black) Connect this lead securely to a clean, bare metal spot on the vehicle’s chassis. Verify this point to be a true ground the vehicle’s chassis. Verify this point to be a true ground negative (-) terminal of the vehicle’s battery

INPUT/POWER CONNECTOR

SWITCH SETTINGS

9: Phase switch 0o to 180o Subwoofer output phase can be set to subwoofer Normal 0o (Button Out) or Subwoofer Reverse 180o
10: Crossover Frequency Adjustment Knob (LP FILTER) Use this control to adjust the crossover frequency between 50 to 150 Hz
11: Input Gain Adjustment Control If the Remote Bass Level Knob will be connected in your system, make sure to rotate the knob fully clockwise (set to “+”) before making the input gain adjustment. Using a dynamic CD as a source, increase the head unit volume until the output distorts. Then, reduce the volume 1 step (or until the output is not longer distorted) Now increase the amplifier gain until the sound from the speakers become distorted.
12: Power Indicator
If the light is green the status of the amplifier circuit is normal.
If the light is red the power supply voltage is too high, the solution is to use the correct power supply voltage.
If the light is OFF the status of the amplifier circuit is subnormal. An electrical short has occurred, or supply current is too high. 15A fuse may be blown, the solution is to turn off the power supply and eliminate the cause (replace necessary). Then turn on the unit and verify that the LED has turned on. If it remains off, turn off the unit and consult your dealer.
13 Remote Gain Adjustment Input The Remote Gain Adjustment allows the user to adjust the overbass level of the subwoofer. Turning the remote bass level knob towards (+) increases the overall subwoofer level, while turning the bass level knob towards (-) decreases the overall subwoofer level.

Note: SQBASS68 can be used without connecting the remote bass level knob. However, overall subwoofer level cannot be adjusted from the listening position

SWITCH SETTINGS

Icon
FOR MORE INFORMATION
PLEASE VISIT
DS18.COM

We LIKE IT LOUD

Logo

Documents / Resources

| DS18 BASS68 6x8 Inch Under Seat Active Subwoofer [pdf] Owner's Manual
BASS68 6x8 Inch Under Seat Active Subwoofer, BASS68, 6x8 Inch Under Seat Active Subwoofer
---|---