INOKIM OX 2022 Red Dot Design Award Electric Scooter User Guide

June 5, 2024
INOKIM

INOKIM - logo OX 2022 Red Dot Design Award Electric Scooter
User GuideINOKIM OX 2022 Red Dot Design Award Electric
Scooter Check out the OX SUSPENSION ADAPTERS PATENT inside!INOKIM OX 2022 Red Dot Design Award Electric
Scooter - figure 1

Congratulations On Your New INOKIM OXO!
We are happy you chose to ride INOKIM.
We hope you find it to be a great riding experience adding efficiency and fun to your daily commute.

A note from the designer:
When I started designing my first electric scooter in 2009, I envisioned a world where cars are used for long-range distances only, while lightweight personal electric devices become the primary way of transportation in urban environments.
After ten years of sales, design, and development of Quick, LIGHT & MINI scooters, we found the need for a more powerful scooter.
Our aim was to provide a good solution for heavier riders, longer ranges and climbs in both urban & off-road surroundings. We created OXO to be a substitute for cars in distances up to 40-50km.
Enjoy, ride carefully and return home safely.INOKIM OX 2022 Red Dot
Design Award Electric Scooter - figure 2

WARNING
It is prohibited to ride in poor weather conditions
Never ride in rain, snow, water, on icy roads, dirty wet roads, poor visibility, or other bad weather conditions.
Always wear a helmet Most serious injuries that occur while riding is head injuries. This can be prevented if a helmet is worn. You must wear a helmet while riding your OXO. The helmet must be  worn according to its instructions
Follow the local laws and regulations. Certain countries or regions require safety devices or gear.
It is your responsibility to know the state laws and follow them
Firmly lock the folding lever and check your brakes before every ride
Do not do stunts, wheelies, or jumps. They increase your chances of injury and might damage your OXO
Do not carry passengers
Make your first ride with INOKIM OXO in a remote location, without any obstacles

DISCLAIMER
Myway Ningbo intelligent technology will not be held responsible for any special, consequential, or incidental damages caused by the use or misuse of our products.
The user agrees to accept full responsibility for all such risks and to not hold my way Ningbo, its distributors or retailers responsible for any incident, injury to persons, or damage to property caused by  misuse of the product

SPECIFICATIONS

MODEL|
---|---
Lithium Battery| 60V  25.6AH
Net Weight (+-0.5 kg)| 33.5 kg
Range (km)| 110 km
With the constant speed of 15 km/H, 75 kg
load, in a temperature of 25°C,
Charging Time (H)| 13.5 hours
Motor-1| 00W gearless (peak 1300W)
Motor-2| 00W gearless (peak 1300W)
Max Speed| According to local regulations
Brakes| Front and rear hydraulic disc brakes
Tire Size| 10 x 2.5-inch pneumatic tires with the option to equip 10 x 3-inch off-road pneumatic tires
Tire Air Pressure| 40 psi to 50 psi
Folded Size L x W x H (cm)| 122 x 59 x 54 cm
Open Size L x W x H (cm)| 122 x 59 x 130 cm
Load Limit| 120 kg
Road lighting| Integral car LED lights
Throttle| LCD display with functions and illumination

Recommended air pressure in tires: 40 psi to 50 psi.

UN-BOX YOUR OXO!

Are you ready to set your OXO free?
Please follow these instructions:

  1. While folded, stand the OXO on the kickstand.
    Push down the rear end of OXO to release the SNAP LOCK and raise up the steering rod
    INOKIM OX 2022 Red Dot Design Award Electric Scooter - figure
4

  2. Adjust the tightening of the lever by the front tension adjuster

  3. Fasten the RED lever

  4. Fix safety lock rubber band

  5. Set the handlebar in place Use the hex key (4m)
    INOKIM OX 2022 Red Dot Design Award Electric Scooter - figure
6

  6. Adjust the brake angle according to your height. A good indication of your suited angle is that your wrists are straight when you ride

  7. Connect the rear mudguard Use the hex key (5m)

  8. When folding repeat steps 2, 3, and 4 in reverse order and then simply snap the steering rod into place

  9. If the SNAP LOCK of your OXO is too loose/tight, you can height of the locking hook. Use hex key (2.5m)

BATTERY

Your OXO has a Lithium Battery with an external charger
When charging, connect the charging cable in this order:
FIRST to INOKIM’s charging socket
THEN to the electrical outlet

Charging Indication:
RED light – Battery charging
GREEN light – Charging complete

MAXIMIZE YOUR BATTERY’S PERFORMANCE:

  1. For its initial charge, FULLY charge your OXO
    This conditions the battery for future life-span

  2. Do NOT leave a fully charged battery connected to a charger, since overcharging may shorten its lifetime

  3. Avoid extreme temperatures Always try to keep the battery between 15°c and 25°c (59°F and 77°F). Extreme temperatures reduce the capacity and lifetime of the battery. A device with a hot or  cold battery may not work temporarily

  4. At least once a month fully charge the battery

  5. From time to time discharge the battery by riding. Use all stored energy in the battery

  6. Before storing it for a long period charge the battery halfway

BATTERY SAFETY REGULATIONS:

Keep the battery away from children & pets
Exposure to the battery voltage can cause death or serious injury
Unplug the battery from the outlet before performing any maintenance
It is dangerous to work on an INOKIM Scooter plugged into an electrical outlet. An electric shock can cause serious injury and damage the scooter
Do NOT use the scooter if the battery:

  • Is damaged
  • Emits an unusual odor or excessive heat
  • Presents any leakage

Do not operate the scooter while charging!
Charge the battery only using INOKIM’s OXO approved charger limits may result in the annulment of the warranty, battery damage, and an ineffective battery charge
DO NOT CUT, OPEN, CRUSH OR PUNCTURE BATTERIES!
IN THE EVENT OF A BATTERY LEAK, PREVENT CONTACT OF LIQUID WITH SKIN OR EYES. IF THIS HAPPENS, WASH THE AFFECTED AREAS IMMEDIATELY WITH  WATER AND SEEK MEDICAL HELP

THROTTLE OPERATION

LCD DISPLAY

THROTTLE BUTTONS INTRODUCTION

INOKIM OX 2022 Red Dot Design Award Electric Scooter - figure
13

WAIT UNTIL THE LCD DISPLAY STOPS FLASHING BEFORE YOU START RIDING

POWER ON| To power on the scooter: press
Wait until the LCD display stops flashing before you start riding
---|---
POWER OFF| To shut down the system: press for three seconds
AUTO-OFF| After 10 minutes of not using any function, the scooter will automatically shut down
ACCELERATION| To accelerate: gently press the thumb lever.
The OXO is powerful so be careful!
| This function is to limit the full speed of the scooter for beginners or for more accurate riding in a crowded surroundings.
The mode can be changed with the buttons
| Your TRIP distance since your last trip reset.
Reset TRIP by long press
To swap to ODO and battery voltage: press
| Your scooter’s total distance since its factory assembly
| Your current battery voltage status
LIGHTS FUNCTION
| To turn the front and rear lights on long press
The LCD back-light indicates that the lights are on.
The lights will turn on automatically if the ambient (You can set it in mode 5, p.15)
Your system has encountered an error, please contact you’re local dealer to find out what it is

DISPLAY MODE SETTINGS

Navigate easily through the settings:
Enter settings (mode1): Press together for 2 seconds.
Switch between modes: Press
Return to main function menu: Long press

LCD BACK-LIGHT
Mode 1| There are 3 levels for LCD brightness: low/medium/high.
To change the level from 1 to 3: Press
Long press to save setting.
Short press to enter Mode 2
---|---
SPEED LIMIT MODE
Mode 2| Default and highest speed: 25km/h at full throttle.
To change the speed limit number: Press or
Long press to save setting.
Short press to enter Mode 3
CRUISE CONTROL
Mode 3| While riding at any same speed for more than ten (10)
seconds, the Cruise Control will be turned on.
When Cruise Control is operated, you can release your thumb from the throttle and the scooter will continue to ride at full speed.
The default for safety reasons: Cruise Control Off (“n” indicates no Cruise Control).
To Enable Cruise Control: Press or (“Y” indicates yes Cruise Control).
Long press to save the setting.
Short press to enter Mode 4

WARNING

Please be aware that when using Cruise Control,
RELEASING YOUR THUMB FROM THE THROTTLE
WILL NOT SLOW YOU DOWN!!!

2 ways to exit Cruise Control:

  • Brake with the LEFT or RIGHT brake lever (both work)
  • Press the thumb lever again.

If you choose to set your Cruise Control to ON. It’s very important you practice your exit so that is comes naturally!

KM / MILE
Mode 4| Default Setting: km/h (“0” indicates km).
Press or alternate to a mile (“1” indicates mile)
Long press to save setting.
Short press to enter Mode 5
---|---
PHOTOCELL
Mode 5| The throttle has light sensors that detect the photographic Default Setting: Photocell On (“Y” indicates yes)
To  disable photocell Press or  (“n” indicates no)
To adjust the light level – When letter is “Y” press
Default value: 510 Press or turn up/down the value.
Long press to save setting

THE OXO SUSPENSION ADAPTERS PATENT

INOKIM OX 2022 Red Dot Design Award Electric Scooter - figure
14

The OXO has a unique patent on the adjustable suspension system.
The OXO Suspension Adapter Patent: OSAP
The OSAP allows you to alternate the suspension position:

LOW POSITION is the default, for better stability mainly at higher speeds
HIGH POSITION is for larger suspension travel, mainly in rough terrain

INOKIM OX 2022 Red Dot Design Award Electric Scooter - figure
15

REPLACING OSAP FROM HIGH TO LOW

In order to turn your OXO into LOW POSITION use the LOW POSITION kit:
It is recommended that you place the OXO on an uplifted surface such as wheels are in the air
Remove the rubber caps and use the 19 mm socket spanner to release the suspension arms from their location
Once the suspension arm is out of its place, replace the OSAP from LOW to HIGH in each suspension arm. Keep front and rear OSAP in their respective places. Assemble back in reverse order. You  can use the sketch below for assistance

INOKIM OX 2022 Red Dot Design Award Electric Scooter - figure
16

CAREFUL RIDING

Get to know your OXO before driving it Test your control over it. Make your turns slowly and cautiously, and give yourself a stopping distance open space with no obstacles to disturb you
The OXO requires a short adjustment and break-in period for all moving parts to adjust themselves into their correct position

Before each ride always:

  1. Check your brakes function

  2. Check the tires for signs of wear
    Spin them to make sure that they are not yet in need of replacing
    Make sure that the wheels are freely rotating clear of the brakes

  3. Perform a visual inspection :
    That all screws and nuts are tight and in place
    Note if anything looks amiss, or is showing signs of wear

If you are unsure, bring your OXO to an authorized INOKIM distributor

RIDING TECHNIQUE:
Before riding position your foot as close as possible to the front section of the scooter, and your other foot on the ground. Make sure that your driving route is clear
To start riding, boost yourself forwards (as on non-motorized scooters) with your foot that is on the ground. Place it on the scooter immediately afterward and press the thumb lever downwards, tilting  your body forwards so you won’t fall backward during acceleration

As you accelerate, lean forwards.
As you brake, tilt your weight backward!

Avoid putting body weight on the handlebars whilst accelerating and decelerating!
Keep one foot behind the other, (it’s more comfortable to place one foot forward and the other one turned backward at 70-90°, like on a skate/surfboard). It will help you gain more stability
Turns – The turns on INOKIM are done as on skis/surf/snowboard. The handlebar should be in parallel to the body. Before turning look in the approaching direction and make sure turning is safe
Braking – Tilt your weight backward so that the brake action will come through the feet and not through the handlebar and steering system.
It is best to learn how to adjust the center of gravity while stopping, otherwise, there is a dual concern: forward tipping over and/or wear and breaking of the handlebar and steering system

Riding, like most sports, involves risks of injury and damage. By choosing to ride INOKIM the responsibility and all inherent risk is on you. It is crucial that you know, understand and act according to  safety rules

FOLDING MECHANISM ADJUSTMENT

If the folding mechanism is too loose or too tight, you can adjust it
The adjustments needed are VERY small.
Work sensitively, be patient and you’ll get it right!

To Tighten / Loosen

  1. The red lever for locking the folding mechanism should be tightened in
  2. If the red locking lever is too loose, open it and tighten the folding system by turning the front tension adjuster approximately 30 degrees clockwise
  3. If the red locking lever is too tight, open it and loosen the folding system by turning the front tension adjuster approximately 30 degrees anticlockwise
  4. Test the function until the pressure of the red lever is reasonably hard and the steering rod is firm
    INOKIM OX 2022 Red Dot Design Award Electric Scooter - figure
17

SERIAL NUMBER

Each INOKIM has a unique serial number
These numbers can provide information that may be useful later on for insurance claims and in case of loss or theft

Write down the serial number of your OXO scooter.
Keep this information separately and in a safe place!

The number is on the BOTTOM REAR SIDE of the boardINOKIM OX 2022 Red
Dot Design Award Electric Scooter - figure 18

Join/create INOKIM RIDERS in your city!

OPERATION & MANAGEMENT
NINGBO MYWAY INTELLIGENT TECHNOLOGY CO., LTD.
17# PUTUOSHAN ROAD, BEILUN, NINGBO,
ZHEJIANG PROVINCE, CHINA 315806
WWW.INOKIM.COM | GLOBAL@INOKIM.COMINOKIM OX 2022 Red Dot Design
Award Electric Scooter - figure 19

INOKIM - logo

WWW.INOKIM.COM

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals