DRAPER 69580 400mm Rotating Laser Level Kit Instruction Manual
- June 5, 2024
- DRAPER
Table of Contents
DRAPER 69580 400mm Rotating Laser Level Kit
GENERAL INFORMATION
These instructions accompanying the product are the original instructions.
This document is part of the product, keep it for the life of the product
passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which
the product has been designed, and contains all the necessary information to
ensure its correct and safe use. By following all the general safety
instructions contained in this manual, it will ensure both product and
operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to
help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information
contained in this manual, the Draper Tools policy of continuous improvement
determines the right to make modifications without prior warning.
TITLE PAGE
INTRODUCTION:
USER MANUAL FOR:
400mm ROTATING LASER LEVEL KIT
Stock no. 69580.
Part no. LLK2.
1.2 REVISIONS: As our user manuals are continually updated, users should make sure that they use the very latest version. Downloads are available from: http://www.drapertools.com/manuals
DRAPER TOOLS LIMITED HURSLEY ROAD CHANDLER’S FORD EASTLEIGH HAMPSHIRE SO53 1YF UK
WEBSITE: www.drapertools.com
PRODUCT HELPLINE:+ 44 (0) 23 8049 4344
+ 44 (0) 23 8026 0784+ 44 (0) 23 8026 0784
GENERAL FAX:+ 44 (0) 23 8026 0784
1.3 UNDERSTANDING THIS MANUALS SAFETY CONTENT:
WARNING! Information that draws attention to the risk of injury or death.
CAUTION! Information that draws attention to the risk of damage to the product
or surroundings.
COPYRIGHT © NOTICE:
Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal & educational
use only. Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted
in any other form or means without written permission from Draper Tools
Limited.
In all cases this copyright notice must remain intact.
GUARANTEE
Draper tools have been carefully tested and inspected before shipment and are
guaranteed to be free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your
nearest distributor or contact Draper Tools Limited, Chandler’s Ford,
Eastleigh, Hampshire, SO53 1YF. England. Telephone Sales Desk: (023) 8049 4333
or Product Helpline (023) 8049 4344.
A proof of purchase must be provided with the tool.
If upon inspection it is found that the fault occurring is due to defective
materials or workmanship, repairs will be carried out free of charge. This
guarantee period covering parts/labour is 12 months from the date of purchase
except where tools are hired out when the guarantee period is ninety days from
the date of purchase. The guarantee is extended to 24 months for parts only.
This guarantee does not apply to normal wear and tear, nor does it cover any
damage caused by misuse, careless or unsafe handling, alterations, accidents,
or repairs attempted or made by any personnel other than the authorised Draper
warranty repair agent.
Note: If the tool is found not to be within the terms of warranty, repairs and
carriage charges will be quoted and made accordingly. This guarantee applies
in lieu of any other guarantee expressed or implied and variations of its
terms are not authorised. Your Draper guarantee is not effective unless you
can produce upon request a dated receipt or invoice to verify your proof of
purchase within the guarantee period. Please note that this guarantee is an
additional benefit and does not affect your statutory rights. Draper Tools
Limited.
INTRODUCTION
SCOPE
This manual is intended to give an overview of this machines features,
functionality and safe operation.
SPECIFICATION
- Stock no. ………………………………………………………………………………………………………………… 69580
- Part no. ……………………………………………………………………………………………………………………. LLK2
- Laser classification …………………………………………………………………………………………………. Class II
- Output power ……………………………………………………………………………………………………….. <1mW
- Wavelength ……………………………………………………………………….. 630-680nM, continuous wave
- Laser accuracy …………………………………………………………………………………………………… 0.5mm/M
- Operating range ……………………………………………………………………………………………………. 3-8M†
- Power source ……………………………………………………………………………………………………… 2 x AAA
Tripod:
- Minimum height ……………………………………………………………………………………….. 420mm
- Maximum height …………………………………………………………………………………….. 1180mm
- †Dependent upon lighting conditions etc.
- WARNING: LASER RADIATION, DO NOT STARE INTO BEAM. CLASS II LASER PRODUCT.
GENERAL SAFETY INSTRUCTIONS
- Laser radiation. Do NOT stare into beam. Class II laser product.
- Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers and microscopes) with a distance of 100mm may pose an eye hazard.
- Viewing the laser output with certain optical instruments designed for use at a distance (for example, telescopes and binoculars) may pose an eye hazard.
- CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
- Do NOT direct the beam towards a person’s eyes.
- Avoid positioning the laser such that it may lead to unintentional eye exposure to any potential passing pedestrians/traffic.
- Do NOT direct the beam towards animals.
- Do NOT use in the vicinity of children.
- Do NOT direct the beam onto reflective surfaces.
- Always switch off when not in use and do not leave unattended. Remove the batteries before storing the laser level away.
- Store the level in a dry location, out of the reach of children.
- Care must be taken to ensure that the laser level is not dropped, knocked or damaged during use or storage.
- This laser level product has no serviceable parts. Do not attempt to disassemble or repair.
TECHNICAL DESCRIPTION
IDENTIFICATION
- Laser beam aperture.
- ON/OFF switch.
- Battery compartment cover.
- Horizontal vial.
- Angle vial (360°).
- Machined base.
- Rotary swivel base.
- Two brass 90° line generating glass prisms.
- 1180mm tripod.
- 2 x AAA batteries.
- Laser enhancement goggles.
UNPACKING: After removing the packing material, make sure the product is
in perfect condition and that there are no visible damaged parts. If in doubt,
do not use the product and contact the dealer from whom it was purchased.
The packaging materials (plastic bags, polystyrene, etc.), must be disposed of
in an appropriate refuse collection container. These materials must not be
left within the reach of children as they are potential sources of danger.
ASSEMBLY
LASER LEVEL BATTERY INSTALLATION (FIG.1):
Unscrew cover A anticlockwise and remove.
Insert the 2 x AAA batteries*, taking note of the polarity indicated on the
side of the level. Replace the cover securely.
- Draper Stock No.61833.
NOTE:
Ensure the laser beam aperture (B) is covered to avoid accidental beam exposure during battery installation/ replacement.
OPERATION AND USE
Remove the tripod from the case, extend all the legs and place the tripod into
position. Ensure the locking screw on the side of the tripod is tight. Adjust
the height of each leg individually to align the bubble on the top of the
tripod as near as possible to the centre of the circle.
Remove the rotary base or the self-levelling laser level from the case and
screw onto the tripod taking care not to disturb its position. Using the three
adjusters, align the bubble on the rotary base as near to the centre of the
circle as possible or align the bubble on the self-levelling laser level as
near to the centre of both vials.
To fine tune the rotary base place the level into the clamp centrally and
tighten. Rotate the level clockwise until it is directly over one of the three
adjusters. Turn the adjuster until the horizontal vial is level. Rotate the
level a further 120° clockwise and adjust it to horizontal. Rotate the level a
further 120° to complete the final adjustment.
NOTE:
If the location or the height of the tripod is changed these adjustments must
be repeated.
LASER LEVEL (FIG.2):
Press the ON/OFF switch into the position marked ‘I’ to turn the laser beam
on, and back to the ‘O’ position to turn the laser off.
NOTE:
The laser ‘spot’ level can be used for distance levelling, spot checking
alignment, reference points etc. The two vials also allow horizontal and angle
levelling.
EXPLANATION OF SYMBOLS
DISPOSAL
- At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations.
- Contact your local authority for details of collection schemes in your area.
In all circumstances:
- Do not dispose of power tools with domestic waste.
- Do not incinerate.
- Do not abandon in the environment.
- Do not dispose of WEEE* as unsorted municipal waste.
CONTACTS
DRAPER TOOLS LIMITED,
Hursley Road, Chandler’s Ford,
Eastleigh, Hampshire. SO53 1YF. U.K.
Helpline: (023) 8049 4344
Sales Desk: (023) 8049 4333
General Enquiries: (023) 8026 6355
Service/Warranty Repair Agent
For aftersales servicing or warranty repairs, please contact the Draper Tools
Helpline for details of an agent in your local area.
drapertools.com
References
- Draper Tools Official Website | Hand Tools, Power Tools and Accessories
- Draper Tools Official Website | Hand Tools, Power Tools and Accessories
- Manuals | Draper Tools
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>