adafruit CYBERDECK Bonnet and HAT for Raspberry Pi 400 Instructions

: June 5, 2024
: adafruit

Table of Contents

Overview
Pinouts
Downloads
- Files:
Schematic and Fab Print for CYBERDECK HAT
Schematic and Fab Print for CYBERDECK Bonnet
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

adafruit learning system
CYBERDECK Bonnet and HAT for Raspberry Pi 400
Created by Kattni Rembor

Last updated on 2021-10-20 01:45:58 PM EDT

Overview

adafruit CYBERDECK Bonnet and HAT for Raspberry Pi 400 -
Overview

Howdy keyboard cowboys, are you surfing the information superhighway with a Pi 400? Want a cool heads-up display, or maybe you need to wire up some NeoPixel wetware…?

adafruit CYBERDECK Bonnet and HAT for Raspberry Pi 400 -
keyboard

Cyber-warriors, listen up here! We’ve got some zero-day unreleased hardware we just dumpster-dived. Now you can crack codes, and write scripts with style, thanks to the CYBERDECK HAT and Bonnet for Raspberry Pi 400 from Adafruit zaibatsu.

adafruit CYBERDECK Bonnet and HAT for Raspberry Pi 400 - Adafruit
zaibatsu

Well, we just fenced 12 megabytes of ram and some angled socket header from the underground hacker club next to the chat sub, and it’s a major upgrade to our extender board – now you can jack in any Pi bonnet or HAT into the back of your Pi 400’s skull at a cool angle, perfect for augmenting your deck!

adafruit CYBERDECK Bonnet and HAT for Raspberry Pi 400 -
board

We also give you two STEMMA (JST 3-PH) connectors on GPIO #18 and #13, and twin STEMMA QT I2C port plugs, for additional upgrades (cables sold separately (https://adafru.it/JRA))

adafruit CYBERDECK Bonnet and HAT for Raspberry Pi 400 -
Fig

This is the same hardware Kevin Mitnick used when he popped Sidewinder! Ok, maybe not, but it will definitely let you create a stand-alone Kali deck by plugging in one of our many display Bonnets or HATs.
Comes completely pre-assembled and tested so you don’t need to do anything but plug it in. Works best with the Pi 400 computer.

adafruit CYBERDECK Bonnet and HAT for Raspberry Pi 400 -
plug

The demo images show the Bonnet with one of our 128×32 OLED bonnets plugged in (https://adafru.it/RfQ). Any bonnet/mini-HAT/pHAT etc should work just fine with the Bonnet as every pin is duplicated from input to output.

adafruit CYBERDECK Bonnet and HAT for Raspberry Pi 400 -
output

Here are some of our favorite displays we recommend for the Bonnet:

Adafruit 2.23″ Monochrome OLED Bonnet for Raspberry Pi (https://adafru.it/RfQ)
Adafruit 2.13″ Monochrome E-Ink Bonnet for Raspberry Pi – THINK INK (https://adafru.it/RfR)
Adafruit 128×64 OLED Bonnet for Raspberry Pi (https://adafru.it/RfS)
Adafruit Mini PiTFT 1.3″ – 240×240 TFT Add-on for Raspberry Pi (https://adafru.it/RfT)
Adafruit Mini PiTFT – 135×240 Color TFT Add-on for Raspberry Pi (https://adafru.it/RfT)
Adafruit 1.3″ Color TFT Bonnet for Raspberry Pi – 240×240 TFT + Joystick Addon (https://adafru.it/NFh)
Adafruit PiOLED – 128×32 Monochrome OLED Add-on for Raspberry Pi (https://adafru.it/NFh)
Pimoroni Inky pHAT for Raspberry Pi – 3 Color eInk Display (https://adafru.it/RfU)
Pimoroni Inky pHAT – 3 Color eInk Display – Yellow/Black/White (https://adafru.it/RfV)

adafruit CYBERDECK Bonnet and HAT for Raspberry Pi 400 -
displays

Here are some of our favorite displays we recommend for the HAT:

Adafruit PiTFT 2.2″ HAT Mini Kit – 320×240 2.2″ TFT – No Touch (https://adafru.it/RfX)
Adafruit PiTFT 2.4″ HAT Mini Kit – 320×240 TFT Touchscreen (https://adafru.it/RfY)
PiTFT Plus Assembled 320×240 2.8″ TFT + Resistive Touchscreen (https://adafru.it/eZS)
PiTFT 2.8″ TFT 320×240 + Capacitive Touchscreen for Raspberry Pi (https://adafru.it/e9Y)
Adafruit PiTFT Plus 320×240 2.8″ TFT + Capacitive Touchscreen (https://adafru.it/CFo)
Adafruit PiTFT – 320×240 2.8″ TFT+Touchscreen for Raspberry Pi (https://adafru.it/dDE)
PiTFT Plus 320×240 3.2″ TFT + Resistive Touchscreen (https://adafru.it/RfZ)
PiTFT – Assembled 480×320 3.5″ TFT+Touchscreen for Raspberry Pi (https://adafru.it/e27)
PiTFT Plus 480×320 3.5″ TFT+Touchscreen for Raspberry Pi (https://adafru.it/Rf-)
Pimoroni HyperPixel – 4.0″ Hi-Res Display for Raspberry P i (https://adafru.it/Rga)
Pimoroni HyperPixel – 4.0″ Hi-Res Display for Raspberry Pi – Non-Touch (https://adafru.it/Rgb)
Pimoroni Inky wHAT (ePaper/eInk/EPD) – Red/Black/White (https://adafru.it/Rgc)
Pimoroni Inky wHAT (ePaper/eInk/EPD) – Black/White (https://adafru.it/Rgd)
Pimoroni HyperPixel 4.0 Square – Touch Display for Raspberry Pi – Capacitive Touch PIM470 (https://adafru.it/Rge)

Pinouts

adafruit CYBERDECK Bonnet and HAT for Raspberry Pi 400 -
Pinouts

I2C Connectors

STEMMA QT – These are the smaller connectors on either side of the HAT and Bonnet. You can use STEMMA QT cables (https://adafru.it/GfR) to connect up a bunch of different sensors and breakouts (https://adafru.it/HMF) with no soldering or breadboard needed! (Cables sold separately.)
These two connectors are connected together in parallel. You can daisy-chain sensors and breakouts connected to them.

STEMMA QT / Qwiic JST SH 4-pin to Premium Male Headers Cable
This 4-wire cable is a little over 150mm / 6″ long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the…$0.95

In Stock
Add to Cart
STEMMA QT / Qwiic JST SH 4-pin Cable – 100mm Long
This 4-wire cable is a little over 100mm / 4″ long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of… $0.95
In Stock
Add to Cart

STEMMA (3-pin JST PH) Connectors

These are the larger connectors on either side of the HAT and Bonnet. You can use these to connect up NeoPixels and more with no soldering or breadboard required! (Cables sold separately.)
They are labeled with their pin numbers: 18 and 13.

Here are some accessories we recommend using with your STEMMA JST PH connectors!

STEMMA JST PH 3-Pin to Male Header Cable – 200mm
This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1″ male header plugs on the end. We’re
carrying these to match up with our… $1.25
In Stock
Add to Cart

STEMMA JST PH 3-Pin to Female Socket Cable – 200mm
This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1″ female header sockets on the end. We’re carrying these to match up with… $1.25
In Stock
Add to Cart

JST PH 3-pin Plug to Color Coded Alligator Clips Cable
This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with grippy mini alligator clips. We’re carrying these to match up with any of our boards or… $1.95
In Stock
Add to Cart

Adafruit NeoPixel LED Strip with 3-pin JST PH Connector
Plug in and glow, this Adafruit NeoPixel LED Strip with JST PH Connector has 30 total LEDs in a “60 LED per meter” spacing,… $12.50
In Stock
Add to Cart

Your browser does not support the video tag.
Adafruit STEMMA Non-Latching Mini Relay
STEMMA plug-and-play parts make your next project soldering-free! This is the STEMMA Non-Latching Mini Relay. It gives you power to control, and control over…$5.95
In Stock
Add to Cart

Raspberry Pi Headers

On the top and bottom of the HAT and Bonnet are the Raspberry Pi headers.

The bottom is meant to plug into a Pi (works best with Pi 400!). They are at an angle to facilitate the Pi 400.
The top headers are to allow you to plug in a HAT or Bonnet. The pinouts are identical – just plug in any HAT or Bonnet!

Adafruit 2.23″ Monochrome OLED Bonnet for Raspberry Pi
If you’re looking for a bright, readable OLED display for a Raspberry Pi (most likely a $22.50
In Stock
Add to Cart

PiTFT Plus 480×320 3.5″ TFT+Touchscreen for Raspberry Pi
Is this not the cutest, little display for the Raspberry Pi? It features a 3.5″ display with 480×320 16-bit color pixels and a resistive touch overlay
Out of Stock
Out of Stock

Downloads

Files:

Fritzing object for HAT in Adafruit Fritzing Library (https://adafru.it/Rgf)
Fritzing object for Bonnet in Adafruit Fritzing Library (https://adafru.it/RgA)
EagleCAD PCB files on GitHub (https://adafru.it/RgB)
3D Model for HAT on GitHub (https://adafru.it/RkA)
3D Model for Bonnet on GitHub (https://adafru.it/Rsb)