KHADAS VIM4 Single-Board Computer with Active Cooling Kit User Guide
- June 5, 2024
- KHADAS
Table of Contents
KHADAS VIM4 Single-Board Computer with Active Cooling Kit
SetUp
OOWOW Introduction
- VIM4 comes with the OOWOW embedded service.
- Use OOWOW to install your preferred OS directly from the Cloud.
OOWOW will start automatically if the device storage is empty.
- Control VIM4 with a display and keyboard, or remotely overWiFi/LAN.
- With OOWOW you will always be in control of your VIM4.
Activate OOWOW: hold Funciton and press Reset Activate Hotspot: press Function after OOWOW starts Network Name: vim4-xxxxx (last 5 digits of serial no.) Further information: https://docs.khadas.com/oowow
Website Introduction
- For more documentation and technical information, you can visit docs.khadas.com.
- If you encounter technical issues during development, seek help at forum.khadas.com.
- To purchase additional accessories, please visit shop.khadas.com.
Data Download Instruction
- Schematics: dI.khadas.com/products/vim4/schematic/
- Datasheets: dl.khadas.com/products/vim4/datasheet/
- Specification: dl.khadas.com/products/Vim4/specs/
- 2D DXF: dLkhadas.com/products/vim4/dx
- 3D CAD: dLkhadas.com/products/Vim4/cad/
After-Sales Service
Please email support@khadas.com if you have any
after-sales related questions.
Interfaces
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) thi s device may not cause harmful
interference, and (2) this device must accept any interference received, incl
uding interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’ s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursua nt to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inte
rference in a residential installation. This equipment generates uses and can
radiate radio frequency energy a nd, if not installed and used in accordance
with the instructions, may cause harmful interference to radio com
munications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turn
ing the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help important announcement
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 0cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. Country Code selection feature to be disabled
for products marketed to the US/Canada. This device is intended only for OEM
integrators under the following conditions:
- The antenna must be installed such that 0 cm is maintained between the antenna and users, and
- The transmitter module may not be co-located with any other transmitter or antenna,
- For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. (if modular only test Channel 1-11)
As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Important Note:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID cannot be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following”
Contains FCC ID: 2A5YT-VIM4″
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module. The end user manual shall include
all required regulatory information/warning as show in this manual.
Integration instructions for host product manufacturers according to KDB
996369 D03 OEM Manual v01
List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the
modular transmitter
Specific operational use conditions
This module is stand-alone modular. If the end product will involve the
Multiple simultaneously transmitting condition or different operational
conditions for a stand-alone modular transmitter in a host, host manufacturer
have to consult with module manufacturer for the installation method in end
system.
Limited module procedures
Not applicable
Trace antenna designs
Not applicable
RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Antennas
This radio transmitter FCC ID:2A5YT-VIM4 has been approved by Federal
Communications Commission to operate with the antenna types listed below, with
the maximum permissible gain indicated. Antenna types not included in this
list that have a gain greater than the maximum gain indicated for any type
listed are strictly prohibited for use with this device.
Antenna No.| Model No. of
antenna:
| Type of antenna:| Gain of the antenna (Max.)| Frequency range:
---|---|---|---|---
BT| /| FPC Antenna| 3.45dBi for 2402-2480MHz;
2.4GWiFi| /| FPC Antenna| 3.45dBi for 2412-2462MHz for Ant1&2
5.2GWiFi| /| FPC Antenna| 1.87dBi for 5180-5240MHz for Ant1&2
5.8GWiFi| /| FPC Antenna| 1.87dBi for 5745-5825MHz for Ant1&2
Label and compliance information
The final end product must be labeled in a visible area with the following”
Contains FCC ID:2A5YT-VIM4″.
Information on test modes and additional testing requirements
Host manufacturer is strongly recommended to confirm compliance with FCC
requirements for the transmitter when the module is installed in the host.
Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module
installed with all other applicable requirements for the system such as Part
15 B.
References
- dl.khadas.com - Index of /products/vim4/datasheet/
- Khadas Documentation [Khadas Docs]
- docs.khadas.com/vim4
- Khadas Community
- Shop | Khadas
- OOWOW [Khadas Docs]
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>