KHADAS KBT-M-001 BT Magic Bluetooth Module User Guide
- June 3, 2024
- KHADAS
Table of Contents
BT Magic Bluetooth Module
User Guide
Interface Diagram
RGB LED Indicator Illustrate
| Status | Motion | Color |
|---|---|---|
| Bluetooth Disconnected | Blue (Flashing) | |
| Bluetooth Connected | Blue (Breathing) | |
| SBC | Yellow (Breathing) | |
| AAC | Green (Breathing) | |
| aptX / apt LL | Turquoise (Breathing) | |
| aptX HD | Purple (Breathing) | |
| LDAC | White (Breathing) | |
| Erase Paring Record | White (Triple Flash) |
Setup Guide
- Power On
Plug BT Magic into the USB-C (I2S) port, then turn on the Tone2/Tone2 Pro. BT Magic will automatically turn on.
-
Bluetooth Pairing
(1) Set Tone2/Tone2 Pro’s input mode to ‘I2S’.
(2) Look for ‘BT Magic’ in your smartphone or tablet’s
Bluetooth pairing list. Tap on it to pair.
-
Music Playback
After pairing with your device, the RGB indicator will show a blue breathing light. BT Magic is now ready for music playback. -
Power Off
When Tone2/Tone2 Pro is turned off, BT Magic will turn off too.
In this case, the RGB indicator light will turn off.
-
Specifications
Bluetooth Chip： Qualcomm QCC5125
Bluetooth Standard： Bluetooth 5.1
Sample Rate： Up to 24bit 96KHz
LED： RGB LED
Connectivity： USB-C
Bluetooth Formats：SBC/AAC/aptX/aptX-LL/aptX-HD/LDAC
Compatibility：Khadas Tone2/Khadas Tone2 Pro
FAQ
How to erase Bluetooth pairing history?****
– With BT Magic plugged in and Tone2/Tone2 Pro powered off (USB cable with 5V power still plugged-in), long-press the volume knob for 5 seconds to Clear Bluetooth Paring Record. BT Magic’s RGB indicator will flash white 3 times during this process.
What’s In The Box
| BT Magic 1pcs
---|---
| Instruction Manual 1pcs
| Warranty Card * 1pcs
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet the general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
FCC ID:2A8Q4-BTM
Manufacturer: Khadas Technology Co., Ltd.
Tel: +86 755 2307 6626
E-mail:[email protected]
Address: Room 2709, Floor 27, Qiancheng Center, Haicheng Road,
Xixiang Street, Baoan District, Shenzhen
Documents / Resources
|
KHADAS KBT-M-001 BT Magic Bluetooth
Module
[pdf] User Guide
BTM, 2A8Q4-BTM, 2A8Q4BTM, KBT-M-001, BT Magic, Bluetooth Module, BT Magic
Bluetooth Module, KBT-M-001 BT Magic, KBT-M-001 BT Magic Bluetooth Module,
Module
---|---