KHADAS VIM1S Low Power SBC User Guide
- June 3, 2024
- KHADAS
Table of Contents
KHADAS VIM1S Low Power SBC
Setup
OOWOW Introduction
- VIM1S comes with the OOWOW embedded service.
- Use OOWOW to install your preferred OS directly from the Cloud.
- OOWOW will start automatically if the device storage is empty.
- Control VIM1S with a display and keyboard, or remotely over WiFi/LAN.
- With OOWOW you will always be in control of your VIM1S.
Activate OOWOW: hold
Activate Hotspot: press and press Reset after OOWOW starts
Network Name: vim1s-xxxxx (last 5 digits of serial no.)
Further information: https://docs.khadas.com/oowow VIM1S Quickstart
Guide
Website Introduction
- For more documentation and technical information, you can visit docs.khadas.com.
- If you encounter technical issues during development, seek help at forum.khadas.com.
- To purchase additional accessories, please visit shop.khadas.com.
Data Download Instruction
- Schematics: dl.khadas.com/products/vim1s/schematic/
- Datasheets: dl.khadas.com/products/vim1s/datasheet/
- Specification: dl.khadas.com/products/vim1s/specs/
- 2D DXF: dl.khadas.com/products/vim1s/dxf/
- 3D CAD: dl.khadas.com/products/vim1s/cad/
After-Sales Service
Please email support@khadas.com if you have any
after-sales related questions
Interfaces
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two
conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
Important Note:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID cannot be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following”
Contains FCC ID:2A8Q4- VIM1S”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/ warning
as show in this manual.
Integration instructions for host product manufacturers according to KDB
996369 D03 OEM Manual v01
List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter
Specific operational use conditions
This module is stand-alone modular. If the end product will involve the
Multiple simultaneously transmitting condition or different
operational conditions for a stand-alone modular transmitter in a host, host
manufacturer have to consult with module
manufacturer for the installation method in end system.
Limited module procedures
Not applicable
Trace antenna designs
Not applicable
RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should
be installed and operated with minimum distance 20cm between the radiator &
your body.
Antennas
This radio transmitter FCC ID:2A8Q4-VIM1S has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Antenna No. | Operate frequency band | Antenna Type | Maximum antenna gain |
---|---|---|---|
Antenna 0 | 2400-2500MHz | ||
5000-6000MHz | FPC Antenna | 2.47dBi For 2.4GWIFI |
1.71dBi For 5.2GWIFI
3.93dBi For 5.8GWIFI
Label and compliance information
The final end product must be labeled in a visible area with the following” Contains FCC ID:2A8Q4-VIM1S “.
Information on test modes and additional testing requirements
Host manufacturer which install this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C:15.247/FCC part 15E:15.407 and 15.209 requirement, only if the test result comply with FCC part 15.247/FCC part 15E:15.407 and 15.209 requirement, then the host can be sold legally.
Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B.
References
- dl.khadas.com - Index of /products/vim1s/cad/
- dl.khadas.com - Index of /products/vim1s/datasheet/
- dl.khadas.com - Index of /products/vim1s/dxf/
- dl.khadas.com - Index of /products/vim1s/schematic/
- dl.khadas.com - Index of /products/vim1s/specs/
- Khadas Documentation [Khadas Docs]
- VIM1S [Khadas Docs]
- Khadas Community
- Shop | Khadas
- OOWOW [Khadas Docs]
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>