EBOYU 2010B Mini Racer Car User Manual
- June 3, 2024
- EBOYU
Table of Contents
2010B Mini
Racer Car
User Manual
2010B Mini Racer Car
(Instructions)
Please read the instructions carefully before operating the toy.
Please keep this instruction sheet for future reference.
Prepare
-
Tear off the sticker, and open the transparent cover in the direction of the arrow.
-
As shown, use a phil1ips screwdriver to unscrew the screws between the controller and the car with the direction of the arrow, and take out the car with the base.
-
Use a Phillips screwdriver to unscrew the screws at the bottom of the car by the direction of the arrow, and remove the race car.
-
Open the battery cover and insert 2AA batteries with the correct polarity. The remote control can only use alkaline batteries. Do not use other types of batteries.
-
Press any button and the indicator light is on, this proves that the battery is installed correctly.
-
Insert and tighten the antenna to the antenna to the antenna hole on the transmitter as the illustration shows.
Charge
-
As shown in the figure, tum on the battery cover, and take out the charge plug.
-
Insert the charging plug into the charging port under the car, and the indicator light is on, indicating that it is charging.
Notice: The car can be charged only when the switch of the car is in the OFF position. -
When the charging light goes off, The mini racer is fully charged.
**Content
** Operate
-
Extend the transmitter’s antenna for better signal reception.
-
Remote control button functions:
(1) After pressing the remote control button, the indicator light will light up, and the car will
(2) When pressing the forward/backward button, the car can go forward/backward.
(3) When pressing the forward/backward button and the left/right button at the same time, the car can tum left/right.
-
Adjust the trimmer on the bottom front of the car to adjust the straight-line performance of the car.
Caution:
a). The car itself uses 1.2V 1/4AAA NI-MH rechargeable built-in battery, the
remote control uses 21.5V AA batteries (not included);
b). The racing car has a superpower. When driving at high speed, it cannot
brake suddenly due to inertia. Please especially pay attention when in use.
c). If the car slows down obviously during running, it may be due to lack of
power, please charge the car following the instruction.
d). When the battery of the remote control is dead, the indicator light turns
dim. The car cannot be charged, please replace the new battery for the remote
control.
e). Pay attention to the charging plug and charging position when charging.
f). When not in use for a long time, please take out the battery of the
controller and turn the power of the racing switch to the “OFF” location.
g). Non-rechargeable batteries shall not be charged. Rechargeable batteries
should only be charged under adult supervision.
h). New and old batteries or different types of batteries must not be mixed.
i). The rechargeable battery should be removed from the toy before charging.
Exhausted batteries should be removed from the toy;
j). Batteries should be inserted with correct polarity to avoid installation
errors.
k). The supply terminals are not to be short-circuited.
l). Unpack under adult supervision.
m). Please keep the above information for future reference.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>