ideal lux Multiflex SP8 Suspension Lamp Instructions

: June 21, 2024
: ideal lux

Table of Contents

ideal lux Multiflex SP8 Suspension Lamp
Product Usage Instructions
FAQ
Dimension
FEATURES
INSTALLATION INSTRUCTION
SAFETY INSTRUCTIONS
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

ideal lux Multiflex SP8 Suspension Lamp

ideal-lux-Multiflex-SP8-Suspension-Lamp-PRODUCT

Specifications

Brand: Multiflex
Model: SP8
Maximum Wattage: 8 x 28W
Voltage: 220-240V
Frequency: 50/60Hz
Color Options: BIANCO, MULTICOLOR

Product Usage Instructions

Installation

The lighting fitting should be installed by a qualified electrician. Follow the assembly instructions in numerical progression.

Safety Instructions

Ensure the device complies with European safety standards EN 60 598-1.
Consult local authorities for proper disposal methods.
Installation must be carried out by a qualified electrician according to regulations.
If the external power cable is damaged, it should be replaced only by the manufacturer, retailer, or a qualified electrician.
Always disconnect the power supply before starting installation or any maintenance.
The device may have hot parts. Handle with care.
Use appropriate fastening accessories for each material. Use only compliant screws and plugs.
The light source uses non-replaceable LEDs. Do not disassemble the source.
If the lamp does not turn on, replace the fuse.
Class I – Electrical safety is ensured by main insulation and a protective conductor (ground) connected to the lamp’s metal structure. Grounding is mandatory.
Class II – Electrical safety ensured by main insulation and double insulation or reinforced insulation. No grounding is required.
Class III – Electrical safety ensured by very low voltage supply (below 50 Volts). No grounding is required.
The device is protected against solid bodies larger than 50mm in diameter.
The device is protected against solid bodies larger than 12mm in diameter.
The device is protected against solid bodies larger than 2.5mm in diameter.
The device is protected against solid bodies larger than 1mm in diameter.
The device is protected against dust ingress.
The device is protected against dust ingress.

FAQ

Q: Can I replace the LEDs in the light source?

A: No, the LEDs are non-replaceable. Do not attempt to disassemble the light source.

Q: What should I do if the lamp does not turn on?

A: If the lamp does not turn on, you may need to replace the fuse. Ensure to disconnect the power supply before performing any maintenance.

Dimension

Suspension lamp

E14 max 8 x 28W / 220~240V 50/60Hz
8021696141893 BIANCO
8021696141909 MULTICOLOR

FEATURES

ideal-lux-Multiflex-SP8-Suspension-Lamp-FIG-2

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN

INSTALLATION INSTRUCTION

ideal-lux-Multiflex-SP8-Suspension-Lamp-FIG-3

THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED.
PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.

SAFETY INSTRUCTIONS

This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor, or by a qualified electrician.
Always isolate power before commencing installation, maintenance, or repair.
The luminaire contains certain parts which can be very hot.
Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
Always tighten the screws firmly to avoid contact problems.
This fitting should only be installed indoors.
Luminaires were not suitable for recessed on normally flammable surfaces.
The luminaire was not suitable for direct mounting on normal flammable surfaces.
This fitting is only suitable for fixing the ceiling.
This fitting is only suitable for fixing the wall.
The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
Only use lamps that do not exceed the maximum specified wattage.
Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
Class Il Electrical safety is guaranteed by the main insulation and double or reinforced insulation.
- Earthing not necessary.
Class III Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
Not Protected
Protected against solid objects greater than 50 mm.
Protected against solid objects greater than 12 mm.
Protected against solid objects greater than 2,5 mm.
Protected against solid objects greater than 1mm.
Dust protected.
Protected against dust infiltration.
Not protected.
Protected against vertically falling water drops.
Protected against water drops falling with a maximum angle of 15° to the vertical axis.
Protected against rain.
Protected against splashing water.
Protected against water jets.
Protected against strong water jets.
Protected against temporary immersion.
Protected against prolonged immersion.
The luminaire was not suitable for covering with thermally insulating material.
Caution, risk of electric shock.
Do not stare at the operating light source.