CONAIR GMTL52 All-in-One Lithium Powered Face and Body Trimmer Instruction Manual

GMTL52 All-in-One Lithium Powered Face and Body Trimmer
Instruction Manual Instruction Booklet
For your safety and continued enjoyment of this product, always read the instruction booklet carefully before using it.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:
READ ALL INSTRUCTIONS BEFORE USING FOR HOUSEHOLD USE ONLY KEEP AWAY FROM WATER DANGER – To reduce the risk of death or serious injury from electrical shock:

1. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place or drop the appliance into water or other liquids.
2. Except when charging, always unplug this appliance from the electrical outlet immediately after use.
3. Always turn this appliance off before cleaning.
4. Do not reach for an appliance that has fallen into the water.

WARNING – To reduce the risk of burns, electric shock, fire, or injury to persons:

1. Except when charging, never leave a plugged-in appliance unattended.
2. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
3. Use appliance only for its intended use as described in this manual. Use only attachments recommended by the manufacturer. Do not use an extension cord to operate the appliance.
4. Never operate the appliance if it has a damaged cord or plug, is not working properly, has been dropped or damaged, or has been dropped into Return the appliance to a Conair Service Center for examination and repair.
5. Keep the appliance cord away from heated surfaces.
6. Do not pull, twist or wrap the cord around the appliance.
7. Never drop or insert any object into any opening on the appliance.
8. Do not place the appliance on any surface while it is operating.
9. Do not use the appliance with a damaged or broken comb or with teeth missing from the blades, as injury may result. Before each use, make certain the blades are aligned properly and oiled.
10. Do not use the appliance outdoors or where aerosol (spray) products are being used or where oxygen is being administered.
11. This appliance is not a toy. Keep away from
12. THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

FEDERAL COMMUNICATIONS COMMISSION NOTICE
WARNING’ Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
• Consult the dealer or an experienced radio/TV technician for help.

SUPPLIER’S DECLARATION OF CONFORMITY

Brand: Conairman®
Model No.: GMTL25
Description: Trimmer
Responsible Party: Conair Corporation, 1 Cummings Point Road, Stamford, CT 06902 203-351-9000
Standards: FCC Part 15 Subpart B, ANSI C63.4-2014
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesirable operation.

DATE OF ISSUE: August 26, 2020

SAVE THESE INSTRUCTIONS

USER MANUAL
Before using the Class 2 Power Supply, read these instructions carefully.
Use with adapter CA92
Rated input voltage: 100-240V AC, 50/60Hz 0.3A
Rated output 5.0V DC 1000mA

CAUTION

1. Ensure the jack is plugged into the trimmer unit before plugging the adapter into the outlet.
2. Do not operate any appliance that has a damaged output cord or housing.
3. Always unplug the unit before cleaning or when not in use.
4. This power unit is intended to be correctly oriented in a vertical or floor-mount position.
5. Be sure the voltage is correct before plugging in.

For connection to a power supply not in the U.S.A, use an attachment plug adapter of the proper configuration for a power outlet. The adapter included automatically adjusts to the input voltage. DO NOT USE WITH A VOLTAGE CONVERTER.

TRIMMER OPERATING

PRECAUTIONS
This trimmer has a built-in rechargeable battery. Do not throw into the fire, apply heat, charge, use or leave in a high-temperature environment.
CAUTION: Any changes or modifications not expressly approved by the Conair Corporation, the manufacturer of this product, and the party responsible for the compliance, could void the user’s authority to operate the equipment.

TROUBLESHOOTING

If your rechargeable trimmer does not seem to be taking a charge, take the following troubleshooting steps before returning it for repair:

1. Be sure the electrical outlet is working by plugging in another appliance to test the outlet.
2. Make sure the electrical plug is not connected to a switch that turns the power off when lights are turned off.
3. Make sure the adapter is inserted into the trimmer properly and all the connections are

OPERATING INSTRUCTION

CHARGING

1. Before using the trimmer for the first time, charge continuously for 3 hours. Maximum battery capacity will be reached only after 3 charging and discharging cycles.
2. To charge the trimmer, first ensure the trimmer is switched off, plug the USB cable into the USB port on the USB adapter with an output of 5.0V DC, 1000mA, then insert the Micro USB plug into the bottom of the trimmer. Plug the adapter into any wall outlet (at the voltage listed on the label affixed to the adapter). Unplug the adapter when not in use.
3. The adapter may become warm while charging, this is normal.
4. The red charging LED indicator light on your new tool will light up when correctly connected to the main power, which will then turn off and the green LED light will then appear once the battery is fully charged.
5. A full charge will supply 120 minutes of cordless runtime.
6. To maintain the optimum capacity of the rechargeable battery, it is highly recommended to fully discharge and then recharge the trimmer for 3 hours every 6 months.

WET/DRY FEATURE
This device is water-resistant. It may be exposed to splashing water in the shower and can be rinsed clean under the faucet, but should never be completely submerged in water.

TRIMMER CHARGING

PRECAUTIONS

• Avoid charging the battery at temperatures below 41°F (5°C) or above 95°F (35°C).
• Avoid charging the battery in direct sunlight or near a radiating heat source.
• Even though the trimmer may not be used for an extended period of time, charge once a month to preserve battery life.
• The power cord cannot be replaced. If it is damaged, the DC adapter should be discarded.

CORDLESS OPERATION

• Plug the USB cable into the USB port on the USB adaptor with an output of 5.0V DC, 1000mA, insert the Micro USB plug into the bottom of the trimmer and then plug it into a suitable outlet and switch The LED light will appear when the adapter is correctly inserted into the appliance and connected to the outlet.
• Once the appliance is fully charged, the green LED light will go on. Unplug the adapter from the outlet, then the appliance, and prepare for use.

USER MAINTENANCE INSTRUCTIONS

REMOVING THE BLADE SET

1. Make sure the trimmer is in the OFF position.
2. Place your thumb against the smaller cutter and push up to remove the blade set.

REPLACING THE BLADE SET

1. Make sure the trimmer is in the OFF position.
2. Align the back prong of the trimmer blade with the guide slot on the trimmer housing, place your thumb on top of the blade and snap it Into

OILING THE BLADES (OIL INCLUDED)

1. Oil the trimmer blades once a month.
2. Turn the trimmer on.
3. Hold and point the blades downward.
4. Spread one drop of oil across the blades
5. Turn the trimmer off and wipe away any excess

NOTE:

1. Do not over-oil the blades, as this can damage the motor.
2. Do not oil the motor bearing, as It is permanently lubricated.
3. KEEP OIL AWAY FROM

BLADE CARE

1. Brush away any loose hair that collects In the blades.
2. Store the trimmer in a safe
3. Sharpen or replace both blades at the same time when servicing your
4. Only use Conair blades with this trimmer (see Parts & Accessories form).
5. Use a trimmer for facial hair

OUTLINING YOUR BEARD

1. Start with a clean, slightly damp beard (NOT WET).

2. Comb through your beard in the direction it grows naturally.

3. Begin under your jawline.

4. Trim from your chin upward, toward your ears.

5. Finish upper outline across cheeks.

TRIMMING YOUR BEARD

1. On the longest setting, begin trimming your beard using smooth, even strokes. Start with your sideburns and work downward toward your (Never attempt to trim against the natural growth of your beard because the hair will be cut too short.)

2. If you decide you want a closer trim, adjust the 5-position comb attachment to a shorter setting and go over your beard until you achieve the desired length.

BLENDING THE JAWLINE

Attach a jawline comb to the trimmer, hold the trimmer in an upright position and begin trimming under your jawline, using short, even strokes.

TRIMMING YOUR MUSTACHE

1. Start with a clean, slightly damp mustache (NOT WET).

2. Comb through your mustache in the direction it grows.

3. Trim your mustache from the top down; finish by outlining the bottom of your mustache.

4. Start with the 5-position attachment comb on the longest setting, as you can always go back and shorten the length as desired.

ROTARY NOSE & EAR TRIMMER

1. Make sure the trimmer is in the OFF position.

2. Insert the pin of the trimmer body into the hexagonal hole of the nose and ear trimmer head as shown (Fig. 1).

3. Press and snap the trimmer head onto the body as shown (Fig. 2).

4. Use the trimmer in a circular motion.

5. To detach the nose and ear trimmer: Hold the trimmer as shown (Fig. 3), with the thumb pressing the top, front part of the trimmer head, and snap it off.

BODY GROOMER

1. Ensure the appliance is switched off.
2. Attach the body groomer head by taking off the current head and snapping the body groomer head into the base of the appliance.
3. Switch the trimmer on.
4. Hold the trimmer flat against the skin.
5. Move the trimmer upward and outward through the hair, against the direction of the hair
6. Make sure to be particularly careful when trimming sensitive areas.
7. The trimmer will work most efficiently when cutting through the hair at its own speed.
8. Never switch the appliance off while in the hair.
9. To remove the body groomer attachment, place your thumb on the back of the attachment and push up.

BODY GROOMER ATTACHMENT

1. Ensure the appliance is switched off.
2. Attach the body groomer head by taking off the current head and snapping the body groomer head into the base of the appliance.
3. Attach the comb guide by placing on top of the body groomer’s head and pressing it down (see Fig. 4).
4. To remove the body groomer attachment, place your thumb on the side of the attachment and push up (see Fig. 5).

|
---|---

BATTERY REMOVAL

1. Using a small Phillips-head screwdriver, remove the screws at the back of the trimmer.
2. Remove the bottom housing and cut the battery Bring the battery to the nearest collection center for proper disposal. DO NOT throw the battery into the normal municipal waste system.

CONTAINS A LITHIUM-ION BATTERY. MUST BE COLLECTED, RECYCLED, OR DISPOSED OF PROPERLY.
DO NOT DISPOSE OF IN THE MUNICIPAL WASTE.

GMTL25 ALL-IN-1 FACE & BODY TRIMMER

WARNING: IF YOU THINK THE POWER IS OFF WHEN THE SWITCH IS OFF, YOU’RE WRONG.

KEEP AYAW FROM WATER

Everyone knows that electricity and water are a dangerous combination. But did you know that an electric appliance is still electrically live even if the switch is off? If the plug is in, the power is on. So when you are not using your appliances, keep them unplugged.

ALWAYS UNPLUG SMALL APPLIANCES

LIMITED TWO-YEAR WARRANTY

(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your unit free of charge for 24 months from the date of purchase if the appliance is defective in workman­ship or materials.
To obtain service under this warranty, return the defective product to the service center listed on the back, together with your purchase receipt. California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instruc­tions. In the absence of a purchase receipt, the warranty period shall be 24 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 24-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Please register this product atwww.conair.com/registration
©2020 Conair Corporation
Service Center
Conair Corporation Service Department 7475 North Glen Harbor Blvd.
Glendale, AZ 85307

HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM OR PURCHASE ON THE WEB AT WWW.CONAIR.COM
Pricing is in effect through December 31, 2025. Orders postmarked after this date will be accepted, and the customer will be notified if pricing has changed.

Enclose check or money order made payable to Conair. (We cannot accept cash, stamps, or C.O.D. orders.) ‘CT, IL, AZ, and PA residents should add applicable state sales tax. Minimum order of $10.00 or a $2.00 handling charge will be added to the order.
All prices include handling and return postage. Prices are subject to change without notice. Prices are valid only for shipments within the continental United States. Please allow 4-6 weeks for delivery.

To avoid delays, please print clearly.
We must have a street address, as UPS cannot deliver to a P.O. Box.

NAME ___
ADDRESS_ APT.
CITY____ STATE__ ZIP____
TELEPHONE ( )__ (We call only if we have a question about your order)
For information on other Conair® haircut kit parts call: 1-800-3-CONAIR.

Documents / Resources

| CONAIR GMTL52 All-in-One Lithium Powered Face and Body Trimmer [pdf] Instruction Manual
GMTL52, All-in-One Lithium Powered Face and Body Trimmer, GMTL52 All-in-One Lithium Powered Face and Body Trimmer
---|---

References

• Conair LLC Consumer Products for Haircare, Beauty, Wellness, Home and Travel
• Welcome | Conair

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>