INTERPHONE URBAN Bluetooth Helmet Intercom User Manual

June 5, 2024
Interphone

URBAN Bluetooth Helmet Intercom

INTERPHONE URBAN

User Manual

[ Download Manual Zip ]

1. INTRODUCTION

1.1 Presentation
Thank you for choosing this product. URBAN Interphone is a Bluetooth® helmet device for wireless entertainment and communication between multiple motorcyclists.
URBAN Interphone can be installed on most helmets with a quick attachment/detachment bracket. URBAN Interphone is certified to withstand harsh weather, with “IP67” protection level.

1.2 Warnings
BATTERY
Fully charge the battery before using the product for the first time.
Do not store the Product without charging it. Failure to do so may cause irreversible damage to the battery capacity. Charge the battery every TWO months.

IMPERMEABILITY
The external unit (control unit), connected to the audio kit, is classified IP67 according to the IEC60529 standard. The control unit, connected to the audio kit, can therefore be immersed in a metre of fresh water for a maximum of 30 (thirty) minutes.
Despite this classification, the device is not immune to greater stress, such as prolonged immersions or high pressure water jets.
Using the product during intense meteorological phenomena, at high speeds, may be equivalent to subjecting the product to a high pressure jet.

FOLLOW ALL SUGGESTIONS CAREFULLY TO AVOID DAMAGING THE DEVICE:

  • Do not immerse the product in fresh water which is more than a metre deep for more than 30 minutes. Do not store the product when still wet: dry it with a clean, soft cloth. Dry any water or moisture present in the connector of the control unit and/or audio kit with hot air for at least 10 minutes, so as to prevent the oxidation of the contacts.
  • Do not expose the product to salt water or ionised water, drinks or other liquids. If the device is exposed to liquids other than fresh water, wash the device with cold fresh water and dry it carefully with a clean, soft cloth.
  • Do not expose the product to high pressure water jets.
  • Make sure that the audio kit connector is completely inserted in the control unit. If not, complete protection against water and dust is not guaranteed.

1.3 Main specifications

  • Intercom: URBAN Interphone allows communication rider-passenger.
  • Telephone/GPS: URBAN Interphone can be connected simultaneously to a maximum of two devices (mobile phone/GPS navigators).
  • Radio FM: URBAN Interphone has an integrated FM-RDS receiver for the 88-108 MHz band. It is possible to store up to 8 stations.
  • Music: URBAN Interphone can play music from Bluetooth® devices, through A2DP and AVRCP profiles (smartphones, MP3 player etc.).
  • Quick touch™: URBAN Interphone features a Quick touch™ interface consisting of four keys for direct access to the functions. The single pressing of a button will activate the corresponding function, quickly and intuitively, without the need for a menu.

1.4 Package contents

Package contents

In the dual version, the material shown in the red box is present in the quantities of two pieces for each component.

2. GETTING STARTED

2.1 Installation instructions
Follow the sequence shown in the figures below for installation of the components.

Installation

2.2 Main commands

Main commands

Main commands

2.3 – Battery charging
Insert the micro USB charging cable into the relevant intercom connector, as shown in the figure. Connect the cable to a standard USB charger.

LED indications:

– red LED: charging.
– mgreen LED: fully charged.

2.4 LED indication

LED indication

2.5 Initial ignition (only dual unit version)
Press on both the units to switch on the devices. The units are already paired by default.

2.6 Initial ignition (only single unit version)
Press to turn the unit on. The device will go into “PAIRING MODE”. These are the possible choices:

  • pairing with Cellularline Interphone devices (see chapter 4.1).
  • pairing with intercoms of other manufacturers (see chapter 4.1.4).
  • phone or GPS navigation pairing (see chapter 5.1).

2.7 Voice guide language setting:

  • With the device turned on, press and hold the UP button (<) until the third beep. The LED will be purple.
  • Press + to select the desired language.
  • Keep pressing the UP button (<) until the third beep to save the selection. The LED will flash blue.

2.8 Listening priority
The device uses the following priorities in managing the various functions:

  1. Mobile phone
  2. Intercom (communication with other intercoms)
  3.  Bluetooth® A2DP audio source (Music from smartphone/Google Maps, MP3 Player etc.)
  4. FM radio

This sequence is used by the device to manage the simultaneous use of multiple functions and to choose which function to stop.

Examples:

  •  if a call is received while listening to music, the latter will be interrupted, automatically switching to the phone audio.
  • If an intercom call is received while engaged in a phone call, the latter will not be interrupted.

3. SETTINGS

Enter settings mode:
With the device turned on, press and hold the UP button (<) until the third beep. The LED will be purple.

Changing the settings:
Pressing each button will change a parameter, according to the figure shown below.

Save the selected settings:
To save the parameters set simply exit the settings mode by keeping pressed the UP button (<) until the third beep. The LED will flash blue.

settings

3.1 System settings

  • LANGUAGE SELECTION each press of the button selects a different language for the voice guidance.
  • AUTOMATIC VOLUME: (INTEGRAL/JET/OFF): the device can automatically adjust the listening volume, depending on the type of helmet being used. The function can be completely disabled, in which case the user will manually adjust the volume. The maximum audio level possible can be obtained with the AUTOMATIC VOLUME OFF.
  • ERASE PAIRINGS: press this button for 5 seconds to delete from the memory all previously paired Bluetooth devices. When erasing the pairings, exiting the Settings mode, the device will automatically enter pairing mode, shown in Chap. 2.6.
  • RDS On/Off: this service allows the device to tune to an alternative frequency when the signal becomes too weak. Each press of the button activates/deactivates the function.
  • VOICE RESPONSE: Where a phone call is received, it is possible to answer the call with a simple voice command. This function can be switched on/off.

4. INTERCOM

The device enables the interphone communication (function named “INTERCOM”) across multiple devices in conference (several people talking at once).

4.1 Pairing
Before starting the communication between intercoms it is necessary to perform pairing of the various devices. This process will only need to be performed once.

Subsequently the interphone will automatically recognise the previously paired devices.
URBAN Interphone is compatible with the entire INTERPHONE range (including the previous series) and with the ANYCOM function. It is also compatible with the interphones of other manufacturers.

Each URBAN Interphone can be paired to a maximum of two intercoms.

WARNING: If a device already has two intercoms paired, performing a third pairing with erase the pairing with the first device paired.

4.1.1: Manual pairing

  1. With the intercom off, on each unit, press and hold until the LED flashes red/blue.
  2. Then briefly press only on one of the two units.

4.1.2: Pairing to a PREVIOUS SERIES INTERCOM device

  1. With the second Interphone unit (previous series) off, press and hold the central MFB button until alternate red/blue flashing of the LEDs.
  2. With URBAN Interphone off, press and hold until the LED flashes red/blue.
  3. Press briefly on URBAN Interphone.
  4. After a few seconds the units will be paired and the intercom conversation will be started.

4.1.3: Pairing with a NON-Interphone (ANYCOM™) device.

  1.  In the NON-Interphone unit, start the telephone search/pairing mode; refer to the user manual of the intercom to be paired.
  2.  With URBAN Interphone off, press and hold until the LED flashes red/blue.
  3.  Press on URBAN Interphone.
  4.  After a few seconds the units will be paired and the intercom conversation will be started.

4.2 Two-unit intercom conversation

  1. Pair unit 1 with unit 2 (Chap. 4.1.1), operation only required the first time.
  2. Press briefly   on unit 1 or on unit 2.
  3. Press again briefly on unit 1 or on unit 2 to interrupt the communication.

4.3 Warnings and suggestions
During use in three/four user conference, to ensure the best system stability, avoid connecting other Bluetooth® devices (telephones, GPS, etc.) to the intercom units.

5. PHONE/GPS

URBAN Interphone can be connected to Bluetooth® devices, such as mobile phones, GPS and MP3 players.

Every URBAN Interphone can be connected simultaneously to up to two Bluetooth® devices (with the exception of using the three- or four-unit INTERCOM function as described in Chap. 4.3/4.4).

5.1 Pairing
Before starting use of URBAN Interphone with these devices, it is necessary to perform pairing of the various devices. This process need only be performed once. Subsequently URBAN Interphone will automatically recognise the devices previously paired and will automatically connect.

Pairing procedure

  1. Activate the Bluetooth® function on the phone/GPS/MP3 (refer to the device manual for further de-tails).
  2. With URBAN Interphone in Standby mode (BLUE LED flashing), press together the buttons + + for 3 seconds to activate “PAIRING mode” (BLUE and RED flashing).
  3. Start searching for new Bluetooth® devices on the mobile phone / GPS / MP3 reader
  4. After a few seconds the device will show “F6T”. Select this option.
  5. If prompted for a PIN or code, enter 0000 (four zeros).
  6. The voice guide will confirm successful pairing with the message “SUCCESSFUL PAIRING, CONNECTED TO THE PHONE”. The device will go into Standby mode (blue LED flashes twice every 3 seconds).
  7. If the Bluetooth® device requires authorisation to access the list, provide confirmation.

To pair a second device, repeat the procedure from step 1).

5.2 Telephone use
As specified in section 2.8, a phone call has the highest priority than any other URBAN INTERPHONE function. In case of receipt of a phone call use the commands shown in the following table:

Telephone use

5.3 Warnings and tips for using the phone
If two different mobiles are connected at the same time, the functions “Redial last number” and “Voice call” may only be used by the first phone connected.
An Internet connection on the mobile phone may be needed to use the “Voice call”.
The “Voice call” function may not be supported by your mobile phone (refer to your device manual for further details).

5.4 GPS
After pairing the URBAN Interphone to the GPS (Chap. 5.1) it is possible to hear the voice prompts sent by the navigator. During the intercom communication the GPS (if fitted) will interrupt the conversation whenever it is necessary to transmit a voice prompt.

Attention: ensure the GPS is compatible with the Bluetooth® headsets. Consult the GPS user manual for further information. URBAN Interphone uses the Bluetooth® HFP profile to manage the connection to a GPS unit.

Navigators integrated within smartphones use the A2DP profile to send route directions. This profile does not allow interruption of the intercom conversation.

Navigators sold for use in cars are NOT usually equipped with Bluetooth® HFP. For that reason they cannot transmit voice prompts to Bluetooth® headsets. Consult the GPS user manual for further information.

6. FM RADIO

URBAN Interphone has integrated FM radio with RDS and 8 stations that can be saved

6.1 Listening to FM radio

FM Radio

6.3 “FM radio” function warnings and suggestions.
URBAN Interphone has an FM receiver with RDS. This feature is used:

  • when the tuned broadcast signal becomes too weak, URBAN Interphone will attempt to tune in to an alternative frequency used by the same station.
  • when the device is tuned in to a radio station, the voice guide will announce the frequency and the name of the broadcaster.

WARNING: In case the signal of the current station is not weak enough to trigger the search for an alter-native station, it is possible that listening will be characterised by disturbances due to poor signal strength. FM reception is strongly influenced by the surrounding environment (electro- magnetic disturbances, natural obstacles etc.).

7. MUSIC

URBAN Interphone can play music from Bluetooth® devices (smartphones, MP3 players etc.) equipped with A2DP profile. To play music it is necessary to pair the devices to URBAN INTERPHONE (Chap. 5.1)

7.1 Playing music

Playing music

7.2 Sharing music
URBAN Interphone has a “SONG SHARING” function which allows music sharing with another Interphone.

Sharing music

During music sharing, by pressing the button it is possible to start an intercom communication.

7.3 “MUSIC” function warnings and suggestions.

  • Only Bluetooth® devices with A2DP profile can transmit stereo music to the device.
  • Only Bluetooth® devices with AVRCP profile can be controlled at a distance from the device.
  • The sound quality of the music also depends on the quality of the audio source (bitrate and codec of audio files, Bluetooth® player quality etc.).

TECHNICAL SPECIFICATIONS:

  • Bluetooth® compliance: Bluetooth® v. 4.2 – Classe II
  • Supported Bluetooth profiles: HFP / A2DP / AVRCP
  • Dimensions mm: 55x85x25
  • Weight: 68 g
  • Capacity: Up to 10 metres
  • Talk time: 20h
  • Stand-by time: 1000 h
  • Charging time: 1,5 h
  • Battery type: Lithium-ion rechargeable

INSTRUCTIONS FOR THE DISPOSAL OF APPLIANCES FOR DOMESTIC USERS
(Applicable in countries in the European Union and in those with separate waste collection systems)

This mark on the product or documentation indicates that this product must not be disposed of with other household waste at the end of its life. To avoid any damage to health or the environment due to improper disposal of waste, the user must separate this product from other types of waste and recycle it in a responsible manner to promote the sustainable re-use of the material resources.

Domestic users should contact the dealer where they purchased the product or the local government office for all the information regarding separate waste collection and recycling for this type of product. Corporate users should contact the supplier and verify the terms and conditions in the purchase con- tract. This product must not be mixed with other commercial waste or disposed of together with other commercial waste.

This product has a battery than cannot be replaced by the user. Do not attempt to open the device to re-move the battery as this could cause malfunctions and seriously damage the product. When disposing of the product, please contact the local waste disposal authority to remove the battery. The battery inside the device was designed to be able to be used during the entire life cycle of the product.

This product is CE marked in accordance with the provisions of Directive R&TTE (1999/05/EC) and of Di-rective ROHS (2011/65/EU). With this, Cellular Italia S.p.A. declares that this product complies with the essential requirements and other relevant provisions of Directive 1999/5/EC and Directive 2011/65/EU. The user is prohibited from making any type of change or variation to the device. Variations or chan-ges not expressly approved by Cellular Italia S.p.A will cancel the user’s authorisation to use the device. Bluetooth® is a trademark owned by Bluetooth SIG, Inc.

For further information, visit the website www.interphone.com


Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals