KNKA QN8014CE Hair Dryer User Manual
- June 15, 2024
- KNKA
Table of Contents
User Manual
Negative lon High
Speed Hair Dryer
Model No.: QN8014CE
QN8014CE Hair Dryer
Warning: Please read this instruction manual carefully before using the
product!
This product is limited to home or similar scenarios.
Executive standard: UL859
Note: When the product picture is slightly different from the actual
product, please refer to the actual product
Product Introduction
Description of Function Button
Note: When the product picture is slightly different from the actual
product, please refer to the actual product
User’s Guidance
Precautions
- Do not use this appliance near a bathtub, shower, washbasin or other utensils filled with water.
- This product has a high working power, please connect it to a socket of 16A or above when using it; at the same time, please confirm that the connected voltage is 120V~.
- When using this product in the bathroom, be sure to unplug the power cord in time after use to avoid danger.
- If the supply cord is damaged, it must be replaced by the manufacturer, an appliance repair department or similarly qualified persons for safety reasons.
- Do not insert foreign objects or metal objects into the hair dryer, so as not to damage the hair dryer or even cause electric shock.
- Do not block the air inlet and outlet of the hair dryer to avoid damage to the hair dryer.
- Do not use this product on wigs.
- when not in use, please place it out of the reach of children and never let it play as a toy.
- Do not allow persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge (including children and the elderly) to use this product.
- Before starting the product, please check the air inlet and outlet to make sure they are not blocked by fluff, hair and other debris.
- When using the product, please keep your hands dry to avoid the risk of electric shock.
- When using the product, please do not touch the air inlet and outlet with your fingers or other metal objects.
- If the product is accidentally dropped from a high place when using the product, please do not pick up the product with your hands immediately Pull out the power cord plug first, and then pick up the product to avoid electric shock caused by touching the damaged product.
- After using the product, please place it on a flat and stable surface to avoid damage from falling from a high place.
- If the shell, structure, or function of the product is abnormal or damaged, please stop using it immediately.
- Do not pull the power cord along sharp or sharp edges, pinch it, or let it dangle as this could damage the power cord.
- Please check the condition of the power cord regularly lf the plug is deformed, the power cord has cracks, copper wires leak, etc., please do not continue to use this product.
- For added protection, it is recommended to install a residual current device (RCD) with a rated residual operating current not exceeding 30mA in the bathroom power supply electrical circuit.
- Please keep plastic bags and other packaging materials used for packaging products out of the reach of children.
Note on Warning Symbols: Do not use in bath or shower. 
Instructions for use
Insert the power plug of the hair dryer into the power socket. After turning on the power, turn the slide switch to the power on, and the hair dryer will turn on.
-
Wind Speed Adjustment:
When the product is in working condition, press the “wind speed key” ” to adjust the wind speed, click once to adjust one gear, and adjust in a cycle within the 1-2-3-2-1 gear; the first gear corresponds to one indicator light on; the second gear Corresponding to 2 indicator lights on, 3 gears correspond to 3 indicator lights on. -
Temperature Adjustment:
When the product is in working condition, click the “temperature button ” to adjust the temperature, click once to adjust one level, and adjust in a cycle within the 1-2-3-2-1 level; the corresponding temperature of level 1 is 140 degrees Fahrenheit, and the corresponding display on the screen 140; the second gear corresponds to a temperature of 175 degrees Fahrenheit, and the screen displays 175; the third gear corresponds to a temperature of 200 degrees Fahrenheit, and the screen displays 200. -
Memory Function:
This product has a memory function. When the product is turned on next time, it will automatically restore the gear used when it was shut down last time, so there is no need to adjust the gear repeatedly. -
Normal Temperature Air/Hot Air Switching:
When the product is in working condition, turn the slide switch to the cold air position , which is the normal temperature wind, and then turn the slide switch to the startup mode to be the hot air gear. -
Nozzle Use:
When the product needs to dry the hair more precisely, the air nozzle can be installed on the air outlet of the hair dryer, and the air nozzle can be aimed at the position of the hair to be dried. -
Self Cleaning Function
When the hair dryer is turned off, rotate the back cover counterclockwise to remove the rear air intake net
Press and hold the “Wind Speed Key ” for 3 seconds to activate the “Self Cleaning Function’, which will automatically stop after 10 seconds
After completing the “self-cleaning function”, the rear air intake net can be reinstalled in its original position
Product Specifications
| Product Name | Negative lon High Speed Hair Dryer |
|---|---|
| Product Model | QN8014CE |
| Rated Voltage | 120V~ |
| Rated Frequency | 60Hz |
| Rated Power | 1500W |
| Product Size | 8.98×5.51×2.36 inch |
Maintenance and upkeep
- After using the product, immediately turn off the hair dryer and unplug the power plug.
- Clean it after the hair dryer has completely cooled down.
- When cleaning hair dryers, use a soft and clean dry cloth to wipe the surface of the housing.
- Do not use cleaning tools with hard materials to clean hair dryers to avoid product damage.
- Do not immerse the hair dryer in water for cleaning.
- During the cleaning process, liquid should be avoided from entering the hair dryer; Do not use a damp cloth to wipe the hair dryer to avoid risks such as short circuits and electric leakage.
Analysis of Frequently Asked Questions
| Problems | Cause | Solution |
|---|---|---|
| The product does not work at all | The power outlet to which the product is | |
| connected may not be energized. | Check whether the power socket has been |
turned on
The power supply voltage connected to the product may not match the voltage
required by the product.| Ensure that the product is connected to a power
supply of 120V-60Hz, consistent with the power supply indicated on the
nameplate.
The product suddenly stops working and the screen displays
EO| The product may have been overheated by the PCBA and automatically turned
on the protection.| Check whether the air inlet of the handle is blocked by
foreign matter.
The product suddenly stops
working and the screen displays
E2| The product may have overheated the heater and automatically turned on the
protection.| Check whether the air inlet at the back is blocked by foreign
objects or remove the rear air inlet net to check whether there is too much
dust blocking the air inlet.
The product suddenly stops working and the screen displays
E4| Voltage is too high| Check whether the connect-ed voltage is 120V-60Hz.
The product suddenly stops working and the screen displays
E5| Voltage too low| Check if the connected voltage is 120V-60Hz.
Note: After analyzing the above phenomenon still can not troubleshooting, please contact us in time, please do not privately disassemble the product!
Web:knkaonline.com
E-mail: service@knkaonline.com
FB: KNKA WORLD
INS: KNKA.WORLD
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>