conforama E-roller und e-scooter User Manual
- June 5, 2024
- conforama
Table of Contents
conforama E-roller und e-scooter
Safe use information
About safe use
Any tool for riding instead of walk has safety risks, and electric scooter is
no exception. Therefore, for your safety sake, you have the responsibility and
obligation to learn how to drive electric scooter, and strictly abide by
relevant local laws and regulations.
- Before each driving, please check whether the tires of the electric scooter are damaged, whether the parts are loose. If there is any abnormal situation, please contact the agent for overhaul in time.
- Please do not use the electric scooter to do anything that endangers the safety of human life or property.
- Please do not modify the parts of the electric scooter privately, which will not only affect the performance of the electric scooter or even damage it, but also cause serious injuries.
Safety instruction
Under whatever circumstances you use an electric scooter, you may be injured
due to loss of control, collision and falling. To avoid injury, you must be
familiar with the manual and ensure that the product is in good condition.
Product introduction
Vehicle diagram
Function introduction
- Switch on / off: long press the power button to turn on / off the power.
- Acceleration: Press the accelerator button on the right hand to start and accelerate.
- Brake: press the brake handle on the left handlebar to brake.
- Up and down gear: when the machine does not accelerate after starting up, gently press the XX button to cycle up and down gear.
- Headlights on /off: Turn on and off the headlights by pressing the button above the headlight when the machine is turned on without acceleration.
- Cruising at constant speed: (cruise can be increased according to customer’s requirements) Turn the throttle to a certain position and hold for 6-8 seconds to enter the cruise mode at constant speed. At this time, release the throttle and the scooter will automatically drive at a constant speed. Press the throttle or brake lightly, and the cruise control will be canceled.
- Warning: the instrument has been set. Please do not change the parameters arbitrarily. If the parameters are changed privately, there will be no warranty.
How to expand
How to fold
Learn how to drive
Charging and precautions
This paper mainly describes the charging method of the electric scooter, the maintenance method of the battery, the safety matters needing attention, and the battery specification. For the safety of you and others, maximize the battery life and improve the battery performance, please be sure to use the battery according to the following operations.
Battery parameters
Name | Parameters | Name | Parameters |
---|---|---|---|
Battery type | Lithium-ion battery | Working temperature | 0℃- 45℃ |
Charging time | 3-6 hours | Charging temperature | 0℃- 60℃ |
Voltage | 36V | Storage time | 3 months (full power) |
Initial capacity (optional) | 5.2Ah 6.6Ah 7.8Ah 9.6Ah | Storage relative | |
humidity | 5% – 95% | ||
Max charging voltage | 42V | Max charging current | 1A – 2A |
Battery safety
- Stop using in case of emitting an odor or excessive heat / leakage of any substance.
- Only professionals can disassemble and maintain the electric scooter.
- Be sure to unplug the charger before driving. It is dangerous to do anything related to electric scooters while charging.
- To obtain the highest operation efficiency of the electric scooter, the battery temperature must be within the temperature range indicated in the battery specification.
- Lithium batteries are considered dangerous and need to be permitted by local laws during transportation.
- The battery contains dangerous substances/Do not disassemble it privately.
- Only the charging equipment provided by our company is allowed to charge the electric scooter. Do not charge indoor.
- It is forbidden to charge the over-discharged lithium battery. Over-discharged batteries have potential safety hazards and can only be scrapped.
- The battery of an electric scooter can only be used under the permission of local laws.
Charging steps
-
Make sure that the charging port is dry without foreign matter, and the electric scooter is turned off.
-
First, plug the charger into the charging port of the electric scooter, and then plug the other end of the charger into the commercial power supply (100v-240v; 50 / 60Hz), and make sure that the indicator lamp of the charger is on normally.
-
When the charger indicator lamp is red, it indicates that the charging is normal. Otherwise, please check whether the circuit is connected well.
-
When the charger indicator lamp is green, it indicates that the battery is full and you can stop charging.
-
After charging is completed, be sure to close the dust cover of the charging port to avoid short circuit caused by the contact with external metal objects or water in the charging port.
- Under the shutdown state, plug the charger into the charging port of the electric scooter.
- It can be charged after power on.
Basic parameters
Expanded size | 10834321168mm |
---|---|
Folded size | 1175432365mm |
Maximum load | 50-100kg |
Body weight | 12.2kg |
Maximum speed | ≤25km/h |
Theoretical endurance | 15-30km |
Maximum climbing | 10°-15° |
Motor parameters | 250w/36v-350w/36v |
Charger output voltage | 42v |
Charger input current | 2A |
Daily maintenance
-
Maintenance precautions:
- Make sure that the charger and charging line of the electric scooter are disconnected, and that the electric scooter is turned off.
- Wipe the shell with a soft cloth to clean the electric scooter. Do not add too much lubricating oil to bearing maintenance.
-
Warning
- It is forbidden to use a high-pressure water gun or soak in liquid to clean the electric scooter, which will cause permanent damage to the internal electronic components of the host.
- In order to protect the safety of users, users are not allowed to disassemble the electric scooter privately, other-wise it will be regarded that the user automatically give up the maintenance and warranty rights of the product.
-
Storage
-
Before storage, please fully charge your scooter to prevent over-discharge of the battery caused by prolonged use. Please make sure to charge and discharge it at least once a month.
-
Do not charge the scooter if the storage temperature is below 0°C. It can be placed in an indoor environment
(above 10°C) for recharging and stored at -10°C-35°C. -
Please store the electric scooter indoors in a dry place with proper temperature. You can shield the electric scooter to prevent dust accumulation from affecting performance.
-
-
Endurance instructions
- Fully charged, 60kg load, 25 ° C. It is measured on the flat and hardened road, no wind environment, driving in cruise mode at a speed of 15km / h. The driving mileage will vary according to different load, wind speed, road conditions and operator habits.
Legal information
-
Recycling:
This product’s packaging materials are recyclable and can be reused. This product and the accessories
packed together are the applicable product to the WEEE directive except batteries. Please dispose of
any materials in accordance with your local recycling regulations. When discarding the unit, comply
with your local rules or regulations. Batteries should never be thrown away or incinerated but
disposed of in accordance with your local regulations concerning chemical wastes. -
Law and Safety:
The CE mark indicates that this product has been manufactured according to current regulations for electromagnetic felds, which means that it is safe to use if used according to safety instructions. The
product is manufactured according to current regulations within the EU legislation, limiting the use of hazardous substances in electrical and electronic equipment. -
We
-
Company name: WINDGOO Technology S.L
-
Postal address: Avenue of Castell de Barbera, number 21-27. Nave2. Industrial polygon Santiga.Spain Declare that the DoC is issued under our sole responsibility and belongs to the following product: Product name: Electric scooter
-
Model: FST10
The object of the declaration described above is in conformity with the the essential requirements of Machinery Directive 2006/42/EC -
The following harmonized standards and technical specifications have been applied:
EN 60335-1:2012+A11:2014+A13:2017
EN ISO 12100: 2010
2006/42/EC Annex I
-
Warranty card
Please keep the warranty card as the after-sale certificate. For non-human damages and malfunctions, after-sales service is provided in accordance with the following terms:
- The whole vehicle is guaranteed for half a year
- The warranty service is only valid under normal use. The appearance of exterior parts is not covered by the warranty.
- All damages such as man-made damage, self-disassembly and improper use are not covered by the warranty.
- This card must be provided during the warranty. If the card is not provided or altered privately, the company has the right to do non-warranty treatment.