Godox SL150II Bi Color LED Video Light Instruction Manual
- June 6, 2024
- Godox
Table of Contents
Godox SL150II Bi-Color LED Video Light
IMPORTANT SAFETY INSTRUCTIONS
When using your photographic equipment, basic safety precautions should always be followed, including the following:
1. Read and understand all instructions before using.
2. Close supervision is necessary when any appliance is used by or near
children. Do not leave appliance unattended while in use.
3. Care must be taken as burns can occur from touching hot parts.
4. The appliance switch is provided with the symbols 0 indicating off and 1
indicating on. The symbols and may be used for this purpose.
5. Do not operate appliance with a damaged cord or if the appliance has been
dropped or damaged – until it has been examined by a qualified serviceman.
6. Position the cord so that it will not be tripped over, pulled, or contact
hot surfaces.
7. If an extension cord is necessary, a cord with a current rating at least
equal to that of the appliance should be used. Cords rated for less amperage
than the appliance may overheat.
8. Always unplug appliance from electrical outlet before cleaning and
servicing and when not in use. Never yank cord to pull plug from outlet. Grasp
plug and pull to disconnect.
9. Let appliance cool completely before putting away. Loop cord loosely
around appliance when storing.
10. To reduce the risk of electric shock, do not immerse this appliance in
water or other liquids.
11. To reduce the risk of electric shock, do not disassemble this appliance,
but take it to a qualified serviceman when service or repair work is required.
Incorrect reassembly can cause electric shock when the appliance is used
subsequently.
12. The use of an accessory attachment not recommended by the manufacturer
may cause a risk of fire, electric shock, or injury to persons.
13. Connect this appliance to a grounded outlet.
14. Disconnect this unit from its source of supply before replacing the
projection lamp.
15. This appliance has a polarized plug (one blade is wider than the other).
To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician.
Do not modify the plug in any way.
SAVE THESE INSTRUCTIONS
Foreword
Thank you for purchasing this Godox Product! With 8 special effects modes, strong power, soft illumination and abundant functions, Bi-color LED Video Light SL150IIBi can achieve creative shooting easily.
Main Features:
• With color temperature adjustment from 2800K to 6500K.
• With 9 FX special effects mode to simulate various of shooting scene.
• Silent mode: without noises and interference.
• Built-in Godox 2.4G wireless & wirelessly adjust parameters.
• With stable light source and 0% to 100% precise light adjustment.
• With 16 groups and 32 channels wireless control.
• With U-type bracket to adjust different angles easily.
• Bowens-mount enables to install various of accessories.
• Clear LCD display.
• Excellent heat dissipation.
Warning
- Always keep this product dry. Do not use in rain or in damp conditions.
- Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
- Keep out of reach of children.
- As this product do not have waterproof function, please take measures of waterproof in rainy or damp environment.
- Do not use the product in the presence of flammable gases, chemicals and other similar materials.
CAUTION : Hot parts!When the product is always on and flickering, please do not touch the high-temperature part of the LED head. When replacing product accessories, please turn off the LED light and perform a cold cut.
Name of Body
LCD Panel
Included Items
Separately Sold Accessories
The product can be used in combination with the following accessories sold
separately, so as to achieve best photography effects: RC-A6 Remote Control,
Power Inverter, Softbox, Photographic Umbrella, Light Stand, Barndoor, Snoot,
etc. 
Power Connection
Use the power cord to connect the LED light to an AC power source and turn on
the power switch.
Operation
Mode Selection
1.1 LED silent mode: in this mode, the fan is turned off. There is no noises
and interference in this mode. In silent mode, the brightness adjustment range
is from 0% to 50%.
1.2 LED special effects modes : Short press the FX button to enter or exit the special effects. When entering the FX modes, FX icon will be displayed on the LCD panel. Then, turn the FX select dial to choose one mode from the 9 special effects modes to achieve creative shooting.
| Display | FX1 | FX2 | FX3 | FX4 | FX5 | FX6 | FX7 | FX8 | FX9 |
|---|---|---|---|---|---|---|---|---|---|
| Scene | Flash1 | Flash2 | Storm1 | Storm2 | TV | Broken bulb | Camdle | Fire |
Firework
Note: Only 6500K color temperature can be displayed in special effects mode.
1.3 LED strong power mode: turn on the fan to enter LED strong power mode and the power will up to the maximum value in this mode.
Light Brightness Adjustment
In LED mode, the light brightness of LED light can be adjusted by turning the
DMX select dial from 0% to 100%. And the light brightness will be clearly
displayed on the LCD Panel.
Color Temperature Adjustment
In continuous LED mode, turn the CCT/FX select dial to adjust color
temperature from 2800K to 6500K. And the color temperature value will be
precisely displayed.
Group GR, Channel CH and ID Setting
GR Setting: Short press GR button to choose group from A, B, C, D, E, F
and 0 to 9.
CH Setting: Short press CH button to choose channel from 1 to
32.
ID Setting: Long press GR and CH button to enter ID setting interface.
Then, turn the DIM select dial to choose ID from OF and 01 to 99.
Wireless Control
With 2.4G wireless system, Bi-color LED Video Light SL150IIBi have receive and control function. Up to multiple groups of LED lights can be controlled. 32 channels and 99 wireless IDs are available with strong anti-interference capability. Please set the channels, groups and IDs of LED light to the same as those of RCA6 remote control before usage.
Adjusting Channel/Group with the Remote Control
- Press the CH/GR button and the group icon blinks. Press the“-”“+”button to choose a group (A to F, 0 to 9).
- Press the CH/GR button twice and the channel icon blinks. Press the“-”“+”button to choose a channel (1 to 32). Adjusting ID with the Remote Control
- Double click the CH/GR button and press the“-”“+”button to choose ID from OFF or 01 to 99. Adjusting Light Brightness with the Remote Control
- Press the“-””+“button to adjust the light brightness. Adjusting Color Temperature with the Remote Control
- Press the SET button of the remote control and the color temperature icon blinks. Press the“-”“+”button to adjust the color temperature. Remote control reset: press down “-” and “+” button simultaneously to reset.
Note : The wireless signal can be received only when the controller of LED light is powered on.
Setting color temperature range
The factory setting of remote control’s color temperature range is 2800-6500K.
In order to use remote control conveniently, color temperature range settings
are added: when the remote control is off, hold down the SET button and turn
it on to enter color temperature adjusting interface. Press CH/GR button to
switch the lowest and highest color temperature value and press “-” or “+”
button to change the value. Press the SET button to confirm it.
Note : the remote control needs to be purchased separately.
Technical Data
| LED Video Light | SL150IIBi |
|---|---|
| Power Supply | AC100V-240V(50/60HZ) |
| Output Power | 150W |
| Color Temperature Range | 2800~6500K |
| 100% Light Brightness(LUX,1M) | ≈30000 |
| CRI = | 96 |
| TLCI = | 97 |
| Light Brightness Range | 0%-100% |
| Operation Temperature | -10 40 |
| Channel | 32 |
| Group | 16(A, B, C, D, E, F, 0-9) |
Dimension (not included a
standard reflector)
| 34x20x16cm
Net Weight(not include reflector and protect cover)| 3.07Kg
Product design and specifications are subject to change without notice.
Maintenance
This product, except consumables e.g. cable, is supported with a one-year warranty. Avoid sudden impacts and the product should be dedusted regularly. Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories. Unauthorized service will void the warranty. If the product had failures or was wetted, do not use it until it is repaired by professionals. Changes made to the specifications or designs may not be reflected in this manual.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
-
This device may not cause harmful interference, and
-
this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warranty
Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!
| Product Information | Model | Product Code Number |
|---|---|---|
| Customer Information | Name | Contact Number |
Address
Seller Information| Name
Contact Number
Address
Date of Sale
Note:
Applicable Products
The document applies to the products listed on the Product Maintenance information (see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached, etc.) are not included in this warranty scope.
Warranty Period
The warranty period of products and accessories is implemented according to the relevant Product Maintenance lnformation. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered onthe warranty card when buying the product.
How to Get the Maintenance Service
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.
Inapplicable Cases
The guarantee and service offered by this document are not applicable in the following cases: The product or accessory has expired its warranty period. Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc; . Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment;.
The original identifying information of product or accessory is modified,
alternated, or removed. No valid warranty card. Breakage or damage caused by
using illegally authorized, nonstandard or non-public released software.
Breakage or damage caused by force majeure or accident. Breakage or damage
that could not be attributed to the product itself. Once met these situations
above, you should seek solutions from the related responsible parties and
Godox assumes no responsibility. The damage caused by parts, accessories and
software that beyond the warranty period or scope is not included in our
maintenance scope. The normal discoloration, abrasion and consumption are not
the breakage within the maintenance scope.
Maintenance and Service Support Information
The warranty period and service types of products are implemented according to
the following Product Maintenance Information:
Product Type| Name| Maintenance Period(month)| Warranty
Service Type
---|---|---|---
Parts| Circuit Board| 12| Customer sends the product to designated site
Battery| 3| Customer sends the product to designated site
Electrical parts e.g.battery charger, power cord, sync cable, etc.| 12|
Customer sends the product to designated site
Other Items| Flash tube, modeling lamp, lamp body, lamp cover, lockingdevice,
package, etc.| No| Without warranty
Godox After-sale Service Call 0755-29609320-8062
Documents / Resources
|
Godox SL150II Bi Color LED Video
Light
[pdf] Instruction Manual
SL150II Bi, Color LED Video Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>