FrSky Taranis X9D Plus 2019 ACCESS Transmitters Instruction Manual
- September 5, 2024
- Frsky
Table of Contents
Taranis X9D Plus 2019 ACCESS Transmitters
“`html
Specifications:
-
Upgraded switches and M9 hall sensor gimbals
-
Features PARA wireless trainer function
-
Compatible with FrSky Free Link App and AirLink S
-
Smart Port for firmware upgrade for all FrSky S.Port
devices -
Battery compartment size: 1003026.5mm (LWH)
Product Usage Instructions:
Overview of Controls:
The Taranis X9D Plus/SE 2019 features various controls including
sliders, sticks, switches, knobs, and buttons. The controls include
SA, SB, SC, SD, SE, SF, SG switches, S1 & S2 knobs, SI tact
switch, and more.
Using the Menu:
To navigate the menus on the Taranis X9D Plus/SE 2019, use the
following elements: Scroll Button for left or right navigation,
MENU Button for accessing the Model menu, PAGE Button for accessing
the RADIO SETUP menu, and EXIT Button for exiting menus.
Warnings for Battery:
Do not remove the battery while the voltage warning is blinking
to avoid internal settings and memories damage. Avoid using the
transmitter if a Backup Error warning occurs.
FAQ:
Q: What is the purpose of the PARA wireless trainer
function?
A: The PARA wireless trainer function enables compatibility with
the FrSky Free Link App and AirLink S for enhanced training
capabilities.
Q: Can I upgrade firmware using the Smart Port?
A: Yes, the Smart Port allows firmware upgrades for all FrSky
S.Port devices.
“`
Instruction Manual for FrSky Taranis X9D Plus/SE 2019
Introduction
The FrSky Taranis X9D Plus 2019 is a re-designed version with additions like
an additional momentary button placed on the top left shoulder making it
ergonomically friendly for DLG pilots to activate launch mode, and features a
program scroll wheel making it even easier to navigate the menus. The upgraded
MCU is used in conjunction with a re-designed mainboard that further increases
the computing capability and increases the data storage. The upgrades not only
improve the running of LUA scripts, it also optimizes overall performance like
voice speech outputs.
The 2019 version uses the latest ACCESS communication protocol, it boasts 24
channels with a faster baud rate and lower latency with a high-speed module
digital interface. Along with the new spectrum analysis function added to the
OpenTX firmware, it is now possible to check the airwaves for RF noise. This
version will give you a further improved experience based on the classic
Taranis remote control. Additionally, tons of extra upcoming features that
ACCESS brings will make this an ideal transmitter for any skill level.
The SE 2019 version is installed with the upgraded switches and M9 hall sensor
gimbals and features the addition of a PARA wireless trainer function which
makes them compatible with the FrSky Free Link App and AirLink S.
Due to unforeseen changes in production, the information contained in this
manual is subject to change without notice. Pay special attention to safety
where indicated by the following marks:
Meanings of Special Markings
DANGER – procedures which may lead to dangerous conditions and cause
death/serious injury if not carried out properly.
WARNING – Procedures which may lead to a dangerous condition or cause serious
injury and even death to the user if not carried out properly or procedures
where the probability of superficial injury or physical damage is high.
CAUTION – Procedures where the possibility of serious injury to the user is
small, but there is a danger of injury or physical damage, if not carried out
properly.
NOTE Steps, Tips or information
WARNING – Always keep electrical components away from children.
Overview
S1 SB SF SE SA
Slider
Stick (J3)
(J4)
MENU PAGE
EXIT Power Switch
SI Hook
Antenna S2 SC SH SG SD
Slider Digital Trim Stick (J2)
(J1)
Scroll button
LCD Diaplay
Switch SA: 3 positions; Short Lever SB: 3 positions; Long Lever SC: 3 positions; Long Lever SD: 3 positions; Short Lever SE: 3 positions; Short Lever SF: 2 positions; Long Lever
SG: 3 positions; Short Lever SH: 2 positions; Momentary,
Long lever S1&S2: Knob, Switch SI: Tact switch, Momentary
1. Micro SD card is not provided with shipment. 2. USB port is for upgrading, reading/writing Micro SD cards and internal memory of radio contents and charging (Includes USB cable in packge but without the adapter). 3. Smart Port is for firmware upgrade for all FrSky S.Port devices. 4. Battery compartment size: 1003026.5mm (LWH
Carrying Bar Infinity 24 Antenna
Recommended 2.4GHz optional high-gain antenna for achieving higher performance and further range.
+X
+Z
Trainer port Mini USB Port
Battery Port Battery Cover
Earphone Port
Smart Port Micro SD Card Port
+Y SMA Connector
FrSky Electronic Co., Ltd.
www.frsky-rc.com
Contact us: frsky@frsky-rc.com
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
Instruction Manual for FrSky Taranis X9D Plus/SE 2019
Warnings for Battery
Do not remove the battery from the X9D Plus 2019/X9D Plus SE 2019 transmitter
while the voltage warning is blinking as this could cause internal settings
and memories to be destroyed. Do not use the transmitter if a “Backup Error”
warning occurs.
Navigate the Menu
To navigate the menus, Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 has the
following elements: Scroll Button MENU Button PAGE Button EXIT Button
Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 supports OpenTX system
Scroll Button
To navigate menus or widgets, roll the button to left or right as navigation.
MENU Button
To go to the [Model] menu, press the button. To go to the [RADIO SETUP] menu,
press the button, and hold for one second.
PAGE Button
To go to switch the page, press the button. To go to the [Telemetry] menu,
press the button, and hold for one second.
EXIT Button
To exit current page or operation widgets.
Where am I in the menu tree
System item Currently selected page
To go to the next page, move the cursor to the item, then Scroll Button roll
to the left or right.
The cursor will firstly stay at the item which indicates the current page.
To change the data in other items, firstly roll Scroll Button to the left or
right until the cursor stays at the needed item.
Secondly, press Scroll Button and roll the button to the left or right.
Overview of the menu tree
Press the MENU button.
Press the MENU button.and hold for one second.
Press the PAGE button.and hold for one second.
FrSky Electronic Co., Ltd.
www.frsky-rc.com
Contact us: frsky@frsky-rc.com
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
Instruction Manual for FrSky Taranis X9D Plus/SE 2019
Specifications
Model name: Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 Dimension:
200194110 (LWH) Weight: Taranis X9D Plus 2019: 670g (without battery)
Taranis X9D Plus SE 2019: 700g (without battery) Operating Current: 130mA@8.2V
(Typ) Backlight LCD resolution: 212*64 Model Memories: 60 models (Extenable by
Micro SD card) Number of channels: 24 channels Operating Voltage Range: DC
6.5~8.4V Opertaing Temperature: -10~60 (14~140) Smart Port, Micro SD card slot
and USB Port OpenTX system
Features
Classic Taranis form factor design High-speed module digital interface Easy
Launch Momentary Button Installed with ACCESS protocol Supports spectrum
analyzer function SWR indicator Haptic vibration alerts and voice speech
outputs
Comparison List
Operating System
Communication Protocol
Program Navigation Button Easy Launch Momentary Button 2S Li-Battery Charging
System* G9D Potentiometer Gimbal M9 Hall Sensor Gimbal
Upgraded Switches
Wired Training System
PARA wireless training function PARA High-speed training system with a lower
latency Compatible with FrSky Free Link App and AirLink S
via mobile devices
Taranis X9D Plus 2019 OpenTX
ACCST D16 /ACCESS
About USB 2S Li-battery balance charging :
The Green Power indicator LED state:
Led on: charging
Led off: charge end
Using the following type of battery:
Led flash: charge fault
Taranis X9D Plus SE 2019 OpenTX
ACCST D16 /ACCESS
Olny 2S Li-Ion/Li-Po battery
Battery + Battery Balance Battery –
PH2.54-XH-3Y
LiFePO4 battery is not supported. Battery compartment size: 1003026.5mmcLWH) Recommended battery pack size: 803024mm(LWH) *USB adapter Voltage: 5V+0.2V Current:2.0A
Note: 1. Charge the battery with the USB adapter (Voltage:5V+0.2V
Current:2.0A) when you use the USB
charging function.
2. The lower the initial charging voltage, the better the charging effect is
when the voltage difference
between the two cells exceed 50 mV.
FrSky Electronic Co., Ltd.
www.frsky-rc.com
Contact us: frsky@frsky-rc.com
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
Quick select options
Instruction Manual for FrSky Taranis X9D Plus/SE 2019
Long press the Scroll Button there will generate a pop-up where the user can
reset timer, reset telemetry values, reset all above, jump to the tele setup
page.
Model Setup for Taranis X9D Plus 2019/Taranis X9D Plus SE 2019 Internal RF
Module
Enter the MODEL SETUP menu. Step 1: Set the Mode for Taranis X9D Plus
2019/Taranis X9D Plus SE 2019 Internal RF. Go to the MODEL SETUP menu, and
select the Internal RF, select [Mode] [ACCESS]. Step 2: Set the Channel Range
The Internal RF module of Taranis X9D Plus 2019/Taranis X9D Plus SE 2019
supports up to 24 channels. The channel range is configurable,and needs to be
confirmed before use. Step 3: Set the Receiver Number When you create a new
model, the system will assign you a receiver number automatically, but this
can be easily changed. The range of the receiver number is 00-63, with the
default number being 01 (use 00 is not recommended). Once the receiver is set
to desired number and is bound to the Taranis X9D Plus 2019/Taranis X9D Plus
SE 2019, the bind procedure will not need to be repeated unless the receiver
number is changed. In this case, either set the receiver number to the
previous one or repeat the bind procedure. Step 4: Registration In ACCESS,
select the Module [Register] into Registration status. Then Press the F/S
button and power on your receiver, and select the “RX Name XX” and [ENTER] to
complete the Registration process then power down the receiver.
Note: If two or three receivers are used at the same time, the UID should be
set to different values.
Step 5: Automatic binding (Smart MatchTM ) Move the cursor to
Receiver1[Bind],and select it , power your receiver, select the RX
and complete the process, the system will confirm “Bind successful”. (You do
not need to press the “F/S” button in ACCESS to Bind. Refer to the receivers
manual for details)
FrSky Electronic Co., Ltd.
www.frsky-rc.com
Contact us: frsky@frsky-rc.com
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
Instruction Manual for FrSky Taranis X9D Plus/SE 2019
Step 6: Set Failsafe mode There are 4 failsafe modes: No pulse, Hold, Custom
and receiver. No Pulse: on loss of signal the receiver produces no pulses on
any channel. To use this type, select it in the menu and wait 9 seconds for
the failsafe to take effect.
Hold: the receiver continues to output the last positions before signal was
lost. To use this type, select it in the menu and wait 9 seconds for the
failsafe to take effect.
Custom: pre-set to required positions on lost signal. Move the cursor to “Set”
and press the Scroll Button, and you can see FAILSAFE SETTING screen below.
Move the cursor to the channel you want to set failsafe on, and press the
Scroll Button. When moving the corresponding sticks or switches, you will see
the channel bar moving. Move the channel bar to the place you want for
failsafe and long press the Scroll Button to finish the setting. Wait 9
seconds before failsafe takes effect.
Receiver: set the failsafe on the receiver (see receiver instructions) in
ACCESS, select it in the menu and wait 9 seconds for the failsafe to take
effect.
Step 7: Range Range refers to Taranis X9D Plus 2019/Taranis X9D Plus SE 2019
range check mode. A pre-flight range check should be done before each flying
session. Move the cursor to [Range] and press the Scroll Button. In range
check mode, the effective distance will be decreased to 1/30. Press the Scroll
Button or EXIT to exit.
FCC
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules
CE
The product may be used freely in these countries: Germany, Italy, Spain,
Belgium, Netherlands, Portugal, Greece, Ireland, Denmark, Luxembourg, Austria,
Finland, Sweden, Norway, Switzerland, France and Iceland.
FLYING SAFETY Warning:
To ensure the safety of yourself and others, please observe the following
precautions. Have regular maintenance performed. Although your Taranis X9D
Plus 2019/Taranis X9D Plus SE 2019
protects the model memories with non-volatile EEPROM memory (which does not
require periodic replacement) and of a battery, it still should have regular
check-ups for wear and tear. We recommend sending your system to your FrSky
Service Center annually during your non-flying-season for a complete check-up
and service.
Battery
Using a fully charged battery (DC 6.5~8.4V). A low battery will soon die,
causing loss of control and a crash. When you begin your flying session, reset
your transmitter’s built-in timer, and during the session pay attention to the
duration of usage. Also, if your model used a separate receiver battery, make
sure it is fully charged before each flying session.
Stop flying long before your batteries become over discharged. Do not rely on
your radio’s low battery warning systems, intended only as a precaution, to
tell you when to recharge. Always check your transmitter and receiver
batteries prior to each flight.
FrSky Electronic Co., Ltd.
www.frsky-rc.com
Contact us: frsky@frsky-rc.com
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
Instruction Manual for FrSky Taranis X9D Plus/SE 2019
Updates
FrSky is continuously adding features and improvements to our radio systems.
Updating (via USB Port or the Micro SD card) is easy and free. To get the most
from your new transmitter, please check the download section of the FrSky
website for the latest update firmware and guide for adjusting your sticks.
(www.frsky-rc.com)
Instruction Manual for FrSky Taranis X9D Plus/SE 2019
Where to Fly
We recommend that you fly at a recognized model airplane flying field. You can
find model clubs and fields by asking your nearest hobby dealer.
Always pay particular attention to the flying field’s rules, as well as the
presence and location of spectators, the wind direction, and any obstacles on
the field. Be very careful flying in areas near power lines, tall buildings,
or communication facilities as there may be radio interference in their
vicinity.
At the flying field
To prevent possible damage to your radio gear, turn the power switches on and
off in the proper sequence:
1. Pull throttle stick to idle position, or otherwise disarm your
motor/engine. 2. Turn on the transmitter power and allow your transmitter to
reach its home screen. 3. Confirm the proper model memory has been selected.
4. Turn on your receiver power. 5. Test all controls. If a servo operates
abnormally, don’t attempt to fly until you determine the cause of the problem.
6. Start your engine. 7. Complete a full range check. 8. After flying, bring
the throttle stick to idle position, engage any kill switches or otherwise
disarm your motor/ engine.
If you do not turn on your system on and off in this order, you may damage
your servos or control surfaces, flood your engine, or in the case of
electric-powered or gasoline-powered models, the engine may unexpectedly turn
on and cause a severe injury.
Make sure your transmitter can’t tip it over. If it is knocked over, the
throttle stick may be accidentally moved, causing the engine to speed up.
Also, damage to your transmitter may occur.
In order to maintain complete control of your aircraft it is important that it
remains visible at all times. Flying behind large objects such as buildings,
grain bins, etc. must be avoided. Doing so may interrupt the radio frequency
link to the model, resulting in loss of control.
Do not grasp the transmitter’s antenna during flight. Doing so may degrade the
quality of the radio frequency transmission and could result in loss of
control.
As with all radio frequency transmissions, the strongest area of signal
transmission is from the sides of the transmitter’s antenna. As such, the
antenna should not be pointed directly at the model. If your flying style
creates this situation, easily move the antenna to correct this situation.
Before taxiing, be sure to extend the transmitter antenna to its full length.
A collapsed antenna will reduce your flying range and cause a loss of control.
It is a good idea to avoid pointing the transmitter antenna directly at the
model, since the signal is weakest in that direction.
Don’t fly in the rain! Water or moisture may enter the transmitter through the
antenna or stick openings and cause erratic operation or loss of control. If
you must fly in wet weather during a contest, be sure to cover your
transmitter with a plastic bag or waterproof barrier. Never fly if lightning
is expected.
FrSky Electronic Co., Ltd.
www.frsky-rc.com
Contact us: frsky@frsky-rc.com
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
FrSky Electronic Co., Ltd.
www.frsky-rc.com
Contact us: frsky@frsky-rc.com
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>