MECHLINE AJPR30 Aquajet with 12-in Bowl Filler Stainless Steel Instruction Manual
- June 5, 2024
- MECHLINE
Table of Contents
MECHLINE AJPR30 Aquajet with 12-in Bowl Filler Stainless Steel
Thank you for purchasing your AquaJet product.
INSTALLATION
Remove the pre – rinse spray from the box and inspect for damage. Check that
you have the fol lowing parts:
Fit the pre-rinse spray into the sink tap hole, and tighten the brass fixing
nut to the underside. Cut the wall bracket to the correct length and fix
securely to the wal l or a solid surface using the screws supplied. Fix the
other end of the wal l bracket securely to the pre-rinse riser
tube.
Water connection: This pre-rinse spray is designed for connection to a cold water supply in the pressure range
water pressure lower than 1.5 bar will affect the performance of the pre-
rinse. Do not connect the pre-rinse to a water supply with pressure higher
than 5 bar. Wat er supply must be flushed free of all debris prior to
connection to the pre-rinse
This pre-rinse spray has been pressure tested to 6 bar (88.2 psi) and has been
flow tested.Before leaving site, fully test the pre-rinse to ensure that
nothing has come loose during the installation / transport process. If you da
have to tighten any joints, do not overtighten or use tools that could damage
the pre-rinse In any way.
When installing the pre-rinse, ensure that any water flexible hoses are not kinked as this will restrict the flow of water.
Installation must be in accordance with local authority water regulations Once the installation is complete, leave this sheet with the operator.
- Do not over-extend spray gun head during use
- Do not extend past the limits of the sink bowl
- Do not pull below the height of the sink top.
- Do not restrain gun handle in open position.
Notes for the operator:Turn off deck tap when not in use
INSTALLATION
Remove the pre-rinse spray from the box and inspect for damage. Check t hat
you have the fol lowing parts:
Fit the pre- rinse spray into t he sink tap hole, and t ighten t he brass fix
in g nut to the underside. Cut the wal l bracket to the correct length and fix
securely to the wal l or a solid surface using t he
screws supplied. Fix the other end of the wall bracket securely to the pre-
rinse riser tube.
Water connection: This pre-rinse spray is designed for connection t o a hot water supply up to 50 C and a cold water supply. Water supply pressures must be balanced.
water pressure lower than 1.5 bar will affect the performance of the pre-
rinse. Do notconnect the pre-rinse to a water supply wi th pressur e higher
than 5 bar. Water supply must be flushed free of al l debris prior to
connection to the pre- rinse
Aqua jet AJPR20 In stall at ion Instructions
- Set brass base nut so that 2 or 3 threads are visible inside of the nut, above the red fibre washer.
- Screw the brass nut/ yoke assembly onto the tap base until the tap base tightens onto the red fibre washer. Do not overtighten. Test for leaks after fitting
- This pre-rinse spray has been pressure tested to 6 bar (BB.2 psi) and has been flow tested. Before leaving site, fully test the pre-rinse to ensure that nothing has come loose during the installation / transport process. If you do have to tighten any joints, do not overtighten or use tools that could damage the pre-rinse in any way.
- When Installing the pre-rinse, ensure that any water flexible hoses ore not kinked as this will restrict the flow af water
- Installation must be in accordance with local authority water regulations Once the installation is complete, leave this sheet with the operator
- Do not over-extend spray gun head during use
- Do not extend past the limits of the sink bowl
- Do not pull below the height of the sink top.
- Do not restrain gun handle in open position.
Tum off deck taps when not in use
MAINTENANCE & CLEANING
Cleaning chrome: Do not use abrasive, chlorine or acid-based cleaning products. Avoid contact with concentrated bleach. Clean with soapy water using a cloth or sponge.All rights reserved. All material on these pages, including and without limitation text, logos, icons, photographs and all other artwork, is copyrightmaterial of Mechline Developments Ltd, unless otherwise stated. Commercial use of this material may only be made with the express, prior, writtenpermission of Mechline. This includes material provided by any third party, including material obtained through links to other sites from Mechline’s pagesor its affiliates and commercial associates. Material and information included are correct at time of print. Intending buyers and users must satisfy themselves as to the suitability ansafety of the products for their particular purposes and duties. Dimensions shown in mm unless otherwise stated. Product accreditationmay not apply to all products in the relevant range. Please contact Mechline to confirm. Unless otherwise stated, all products carry a warranty of twelve (12) months against manufacturing defect or workmanship on parts with no inclusion for labour or site attendance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>