elgato Light Strip RGB LED 2000 Lumens User Guide
- June 5, 2024
- elgato
Table of Contents
Light Strip RGB LED 2000 Lumens
User Guide
Contents
Mounting
The length of the Light Strip can be adjusted to accommodate your chosen
application. To shorten Light Strip, use a pair of scissors to cut along an
indicated trim line (approximately every 33 cm | 13 in).
Disconnect Light Strip from power before shortening.
Clean the mounting surface with a lint-free cloth. Peel back some of the protective films to expose a short section of the adhesive backing on Light Strip, and stick to the mounting surface by applying pressure for 5 to 10 seconds. Slowly peel back the remaining film with one hand while using the other hand to press down newly exposed sections of the adhesive backing. Once fully mounted, run your fingertips firmly along the full length of the Light Strip to maximize bond strength. Use the additional tesa® adhesive strips to mount the controller.
Installation
-
elgato.com/download
Download and install the Control Center app for Mac, Windows, iOS or Android. -
Connect the LED strip to the controller. Then connect the controller to the power supply and plug it into a power outlet.
After powering up, Light Strip will quickly color cycle and engage in pairing mode. -
Launch the Control Center app and pair Light Strip by clicking the + icon. Control Center will guide you through the setup process.
For Wi-Fi pairing using a Mac, turn on your Light Strip, click the Wi-Fi icon in the top right Status menu, and select your new accessory. After completing the Airport Utility setup process, your Light Strip is accessible from Elgato Control Center. -
Use Control Center to switch Light Strip on/off, adjust brightness, fine-tune color, and set temperature.
If your PC is not equipped with Wi-Fi, use the Elgato Control Center app on your iOS or Android device to add Light Strip. A Wi-Fi connection is only needed for initial pairing. Once paired, you can control Light Strip via any wired or wireless device in your network.
Reset
RESET will restore Light Strip factory settings and forget all Wi-Fi
credentials.
Push and hold the RESET button with a small tool for at least 10 seconds until
the light flashes red 3x.
Light Strip will reboot automatically and color cycle before reengaging
pairing mode.
Warning
- Light Strip may become hot during prolonged use. Always handle with care.
- Light Strip is made for indoor use only.
- Do not cover this product, especially the controller.
- Be especially cautious when setting up near children.
- Do not leave Light Strip in direct sunlight.
- Keep the lighting surface free from dirt and dust. If Light Strip becomes dirty, wipe it lightly with a soft cloth moistened with a little water and mild, neutral detergent. Benzene, thinner, and other volatile agents can cause permanent damage and should never be used for cleaning.
- Do not use the product for applications other than those specified in this guide or the packaging.
- Do not use accessories other than those supplied with the product or stated as compatible by the manufacturer.
Frequency range: 2412 – 2472 MHz (2462 MHz for FCC, ISED), Max RF e.i.r.p power < 20 dBm, Temperature range: 0 °C – 45 °C. Hereby, Corsair Memory Inc. declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EC. The declaration of conformity for Elgato products is available at www.elgato.com/doc
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and a human body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For questions about Elgato product compliance with FCC regulations, please contact: Compliance Officer, Corsair Memory Inc., 47100 Bayside Pkwy, Fremont, CA 94538, USA
This device complies with ISED’s license-exempt RSSs.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. This
equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
Le present appareil est conforme aux CNR d’ ISED applicables aux appareils
radio exempts de licence.
Elgato, a division of:
Corsair Memory Inc., 47100 Bayside Pkwy, Fremont, CA 94538, USA
Corsair Memory, BV Wormerweg 8, 1311 XB, Almere, Netherlands
Copyright 2018 – 2021 Corsair Memory Inc. All rights reserved. Elgato and the
Elgato logo are trademarks of Corsair Memory Inc., registered in the U.S. and
other countries.
Part: 51LAA9903
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>