ENTRO A0400SSSM Narrow Stile Mortice Lock Instruction Manual
- June 5, 2024
- ENTRO
Table of Contents
A0400SSSM NARROW STILE MORTICE LOCK
Installation Instructions
HANDING OF DOOR
RIGHT-HAND DOOR
| OUTSIDE DOOR OPENING IN
---|---
| OUTSIDE DOOR OPENING OUT
LEFT-HAND DOOR
| OUTSIDE DOOR OPENING IN
---|---
| OUTSIDE DOOR OPENING OUT
IMPORTANT:
Before drilling the door, ensure correct handing is being installed
NOTE:
The case does not need to be opened at any time to change the function or
handling of this lock
DOOR PREPARATION
METAL DOOR PREPARATION
- Determine the height of the lockset on the door
- Cut out the mortice window 156mm x 25.5mm with 3mm radius corners
- Place template in opening and drill 4.5mm holes, countersink with 8mm dia at 90°
- Drill other appropriate holes for the selected lockset. Dimensions in the illustration suit a 23mm backset lock
- Do not drill holes all the way through to avoid door damage or incorrect installation
NOTE: Ensure the door furniture supplied matches the correct hole dimensions being drilled.
LOCK PREPARATION
CHECK LOCK STATUS
Ensure that the locking bar is in the unlocked position (UP). If the position
needs to be changed to the unlock position, use a small flat blade
screwdriver, to lever out the plastic cylinder hole plug (where fitted) and
lift the locking bar using the screwdriver.
LOCK FUNCTIONS
Depending on the locking function required it can be set to any vestibule or
combination lock status. To change the locking function, use a small flat
blade screwdriver to rotate (AntiClockwise Only) the locking wedge to the
desired location. Refer to the Locking Status label on the lock body for
further detail.
LOCKING STATUS
The locking bar must be UP (unlocked) to change
| Both Side Lockable (Warning! Not suitable for Escape Doors)
---|---
| Other Side Locking (Right-Hand Doors)
| This Side Locking (Left Hand Doors)
| Rotate AntiClockwise Only
REVERSE BOLT HEAD FOR HANDING
Determine lock handing from the Handing of Door chart. Rotate bolt head if
required by removing Face Plate to pull and rotate the bolt 180° to suit the
Latching direction.
TURN ADAPTOR INSTALLATION
ENTRO turn adaptors are captive adaptors and must be installed correctly
for proper lock operation.
- Determine to hand for adaptor
- Put lock into LOCKED STATUS by moving locking bar in down position.
- Insert adaptor ensuring the cam plate is engaged with the locking bar.
- Insert retaining pin and test operation, ensuring the locking bar is operating up & down with operation of cam (Maximum ¼ turn left or right).
- Lock can now be left in UNLOCKED STATUS with lock bar UP until installed on door.
LOCK INSTALLATION
FIT LOCK
Insert Lock into the door and secure with 2 screws.| LOCKS WITH CYLINDERS
-
screwdriver, lever out Using a small flat the cylinder hole plug,
where fitted. Insert the lock into the door and secure it with 2 screws. -
Secure cylinder with retainer pin, ensuring pin is flush with front face or lock.
-
Install faceplate and secure with 2 screws.
| LOCK WITHOUT CYLINDER
Install faceplate and secure with 2 screws.LOCKS WITH TURN SNIB
Mark and cut the connecting bar as shown. The turn snib must be in the
vertical position when unlocked. 5mm| LOCKS FOR DOOR LEVERS WITH SPINDLES
Insert spindle/s into the lock as required, ensuring the spindle spring is
attached to
the rear of the spindle before assembling.
---|---|---|---
| | |
DOOR FURNITURE INSTALLATION
FIT FURNITURE
Rotate handle to the desired handing as shown. Ensure furniture screws are
minimum 5mm and a maximum 15mm past the door face. Position furniture plates
and secure them with mounting screws.
FIT MOUNTING STRIKE
- Prepare doorjamb cutout and fit Strike Box to frame.
- Fit Strike to Strike Box and secure with 2 screws.
A0400SSSM NARROW STILE MORTICE LOCK
www.entro.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>