new garden solar floating User Manual
- June 5, 2024
- new garden
Table of Contents
new garden solar floating
Warning
WARNING Read the instructions for use carefully before handling the product. NEWGARDEN cannot be held responsible if the usage guidelines and/or product recommendations described in these instructions have not been followed. IP68: Newgarden products with IP 68 can be used outdoors, are dust and rain tight. It is also floating (not submersible) so you can use it in your swimming pool. In case of very adverse weather conditions, it should be protected from the elements to avoid future problems. Follow these instructions to avoid, falls, electric shocks, or product installation and start-up failures. Save these instructions for future use. Remove the assembly from the box before connecting it. Any internal changes to the lamp by the user will render the product out of warranty. This lamp is not protected against immersion in water, if improperly installed, it will cause accidents. Do not place the product next to heat sources, it could damage the product and ultimately cause a fire. Keep combustible materials away from the bulbs. Do not allow the lamp or connector to come into contact with walls, fabrics associated with curtains, blinds or other materials. In case of abnormal operation, disconnect the product and contact qualified personnel. A full charge is recommended before first use. Do not use the product in case of damaged cable or broken lamp. In this case, it must be replaced exclusively by the manufacturer or Authorised Technical Service, in order to avoid any risk. The fixed joints must be tightened to 2.5 Nm to avoid loosening. The light source of this luminaire is not replaceable. When the light source reaches the end of its service life, the complete luminaire must be replaced. Any modification to the luminaire by the user will render the product out of warranty. Use only components supplied by Newgarden Spain, SL. Any electronic components other than those supplied may seriously damage the operation of the product. For decoration only. This bulb is not a toy. Do not allow children to play and manipulate the bulb. (1) CE: Compliance with the European Directives for Electrical Safety and Electromagnetic Compatibility. (2) The crossed-out wheeled bin symbol on the appliance or packaging indicates, that this product is subject to a separate collection. Electrical and electronic equipment must be collected and not disposed of with household waste. Waste electrical and electronic equipment must be labeled with a collection system in accordance with Directive 2012/19/EU. Electrical and electronic equipment is hazardous to the environment and human health due to the presence of a hazardous substance in its composition. Proper storage and collection of one of these products contribute to the protection of the environment and public health and are basic conditions. Recycling of used electrical and electronic equipment. For more information on the delivery and collection of used electrical and electronic equipment, please contact your local authorities and the collection center authorized in this regard. (3) A Class III appliance is designed to be powered by a Separated or Safety Extra-Low Voltage (SELV) power supply. The voltage of a SELV supply is sufficiently low that, under normal conditions, a person can come into contact with it without risk of electric shock. Therefore, it is not necessary to incorporate the safety features of Class I and Class II devices. For compliance of Class III medical devices, it is not considered sufficient protection. (4) In the event of a crack in the protective screen, it must be replaced. (5) CMIN: Compliance with Kingdom of Morocco Electrical Safety and Electromagnetic Compatibility regulations, as applicable.
Manuel
Press the On button pointing directly at the product and at a distance of less than 3m, then press the Manual button and the product will flash red twice to indicate that it is in MANUAL mode. In this mode, the user has full control of the product and can turn it on and off at any time.
Night mode
Press the On button pointing directly at the product and at a distance of less than 3m, then press the SENSOR ON AUTO button and the product will flash green twice to indicate that it is in Night mode. This mode means that during the day the product does not switch on and activates when it is nighttime or in a sufficiently dark area. It is recommended not to place the product near any light source so that it can distinguish day from night. If it is daytime and you press any button on the remote control, the product will flash green indicating that it is in night mode and will not turn on until it is dark enough. Once a sufficient level of darkness is detected, the product will automatically switch on for up to 6 hours, depending on the battery level. After 6 hours of operation, the product will automatically switch off to save energy.
INSTRUCTIONS OF THE REMOTE
- Light On
- Light Off
- The lower color intensity or speed of change.
- Night mode
- White color
- Manual mode
- Primary colors
- Higher color intensity or speed of change.
- 50% intensity of light
- Changing colour modes
CHARGING INSTRUCTIONS
Solar
Leave the product exposed to the sun for as long as possible. The dimensions of the product and the hours of exposure may vary the autonomy time of the product. With SOLAR charging, the product will have an autonomy of 2-6 hours in NIGHT mode and 2-4 hours in MANUAL mode at maximum intensity.
OPERATING INSTRUCTIONS
(1) Remove the PVC protection from the batteries before using the remote control. (2)Press the ON button on the remote control to turn on the product. The product will turn on for the first time in MANUAL mode and you can change the colours and their intensity, as well as the operating modes and speed.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>