ReXING V1PGW-4K Dual Channel Car Dash Cam 2160p User Manual
- June 5, 2024
- Rexing
Table of Contents
V1PGW-4K Dual Channel Car Dash Cam 2160p
User Manual
About Us
Thank you for choosing REXING!
We hope you love your new products as much as we do. If you need any
assistance or have any suggestions to help us improve, please contact us.
care@rexingusa.com
877-740-8004
Our support team will respond to you as soon as possible.
Always a surprise in Rexing.
Check us out here
- https://www.facebook.com/rexingusa/
- https://www.instagram.com/rexingdashcam/
- https://www.rexingusa.com/support/registration/
- https://www.rexingusa.com/support/product-support/
https://www.rexingusa.com/support/registration/| https://www.facebook.com/rexingusa/| https://www.instagram.com/rexingdashcam/| https://www.rexingusa.com/support/
Package Contents
| 1. Rexing V1PGW-4K Dash Cam | 6. Car Charger |
|---|---|
| 2. Rear camera with rear camera cable | 7. Cable Management Tool |
| 3. Mini-USB Cable | 8. Safety Guide |
| 4. Mount Plate & 3M Adhesive | 9. User Manual |
5. Cable Clips
Camera Overview
| 1. Micro SD Card Slot | 7. OK (Confirm) Button |
|---|---|
| 2. Power Button | 8. MIC (Microphone) Button |
| 3. Reset Button | 9. Screen Button |
| 4. Menu Button | 10. Mini-USB Power Port |
| 5. Mode Button | 11. Rear Camera Port |
| 6. REC (Record) Button | 12. Lens Angle Adjustment Dial |
| 1. Recording Mode | 10. Time (24H) |
|---|---|
| 2. Recording (On) | 11. Current Date Time |
| 3. WDR Mode (On) | 12. MIC (Off) |
| 4. G-Sensor Sensitivity Level | 13. Exposure Value |
| 5. Recording Time (Current Clip) | 14. Loop Recording Time Interval |
| 6. Video Resolution | 15. GPS Signal (connected) |
| 7. Parking Mode (On)*** | 16. Battery Charging |
| 8. GPS Signal (not connected) | 17. Plate Number |
| 9. Memory Card (Inserted) | 18. MIC (On) |
*** Please connect a Smart Hardwire Kit or an Intelligent Hardwire Kit to activate the parking monitor feature.
Get Started
Step 1
Installing Adhesive Mount
Place the 3M adhesive on the mounting plate and properly orient the mounting
piece to the roof and hood line of the vehicle.
Important! Ensure the T-interlock on the mount is oriented in the correct
direction.
Firmly press the mount onto the windshield. Wait at least 20 minutes before
mounting the camera.
Step 2
Mount the Rear Camera
Mount the rear camera as shown below. Use the included rear camera cable to
connect the rear camera to the front camera.
Step 3
Insert the Memory Card
The Rexing V1PGW-4K accepts Class 10/ UHS-1 or higher Micro SD memory cards up
to 256GB. You will need to insert a memory card before recording. Before
inserting or removing a memory card, ensure you’ve powered down the device.
Gently push the memory card in until you hear a click, and allow the spring
release to push the card out. 
Step 4
Power on the Camera and Format the Memory Card
Place the camera on the mount and carefully route the power cable around the
windshield and tuck it in under the trim.
Power the camera by connecting the charger to the car cigarette lighter and
the camera. 
The camera will shut down after 3 seconds when it’s disconnected from the
power source and it should begin recording automatically the next time it is
powered on.
To ensure the V1PGW-4K records to your memory card properly and without error,
we strongly recommend you format the card within the camera when you’re using
the dash cam for the first time.
Note:
Always remember to backup important data stored on the memory card before
formatting.
To format the memory card, first press the REC button to stop recording. Then
press the MENU button twice to enter the Setup Settings. Use the REC and MIC
buttons and toggle to the Format. Press the OK button to confirm the format.
Basic Operation
Device Power
The device is automatically powered on when plugged into a 12V accessory
socket or cigarette lighter and receives a charge (i.e.: the vehicle is
started).
To turn the device on manually, press and hold the POWER button until the
welcome screen appears.
The camera will automatically start recording when power on.
Menu Settings
Power the camera on, then press the REC button to stop recording. Press the
MODE button and switch between video mode, image mode, and playback mode.
Press the MENU button once to enter the Video Settings, or press the MENU
button twice to enter the Setup Settings menu.
Video Recording
The camera will automatically start recording when the device receives a
charge.
The LED lights and the red dot will blink when the device is recording. Press
the REC button to stop recording. 
Video Playback
To playback, a video on the device, press the REC button to stop recording.
Press and hold the MODE button twice to enter the Playback mode. Use the REC
and MIC buttons to toggle to the desired video. Press the OK button to play.
During playback, use the OK (pause), MIC (fast forward), and REC (rewind)
buttons to control the video playback.
To playback a video by using an SD card reader, remove the memory card and insert it into an SD card adapter. Place the adapter in the computer.
Parking Mode (Parking Monitor)
To activate the Parking Mode, you’ll need to connect to a smart hardwire kit
or an intelligent hardwire kit.
Parking mode provides surveillance on your parked vehicle. When the engine is
off, hardwire kit is used to provide continuous power and protect your car
battery from being discharged.
Option 1: Vibration Detection
To activate the Parking Mode, you need to connect it with a Smart hardwire kit
(ASIN: B07RN24B7V, sold separately).
Time-lapse Recording:
Record video in one frame per second to conserve memory and reduce the time it
takes to review the video.
G-Sensor Trigger Recording:
The G-sensor detects significant or sudden movement (such as an impact or
collision), it will trigger an event recording. We suggest setting the
“Gravity Sensing” to High sensitivity for Parking Mode Recording. The dash
cam will remain off until a movement is detected.
Note
If you do not use the parking mode function, please change the G-Sensor
setting to low sensitivity. Otherwise, the dash cam will easily lock the
videos and these videos cannot be deleted by the loop recording function. This
will cause the memory card to be full of locked videos and cause the recorder
to fail to work normally.
Option 2: Motion Detection
To use this feature, you need to connect it with an Intelligent Hardwire Kit
(ASIN B0973MBCT8 sold separately). Make sure that the Parking Mode is turned
off on your dash cam.
Once the sensor has detected MOTIONS. The intelligent hardwire kit will power
up the dash cam automatically and start recording until the MOTION is cleared.
Wi-Fi Connect
Download the Rexing Connect app from the App Store/Google Play.
- Press the REC button to stop recording then press the MENU button once to enter the Video Settings.
- Use REC/MIC buttons and toggle to Wi-Fi to turn it on.
- Turn on Wi-Fi on your phone, then find B50E_XXXX from the network list and enter the default password 12345678 to connect.
- Open the Rexing Connect app, and tap “Connect” to enter the real-time video streaming view.
- You can always access or turn off the Wi-Fi by pressing and holding down the REC button.
Built-in GPS Logger
GPS logger will record the speed and location of your vehicle as you drive.
You can then access this information while playing back your recordings using
the GPS Video player.
Press the MENU button twice and enter the Setup Settings. Toggle to the GPS
Speed Unit and select your preferred speed unit.
After a GPS signal is found, the screen icon will turn from blue to green.
Please visit https://www.rexingusa.com/support/videos/ to watch a video
tutorial.
Download GPS Video player
Please download the GPS logger player through the link OR Scan the QR Code
below.
Taking and Reviewing Photos
To take a photo, press the REC button to stop recording. Press the MODE button
twice to enter photo mode. Then press the OK button to take a photo.
To view/delete a photo, stop video recording and enter the Playback Mode.
Toggle through the videos and photos to the one you want to view/delete. Press
the MENU button once and toggle to the Delete option. Press the OK Button and
select Delete Current or Delete All.
Warranty & Support
Warranty
The Rexing V1PGW-4K Dash Cam comes with a full 12-month warranty. If you
register your product on our official site
(https://www.rexingusa.com/support/registration), you can extend the
warranty to 18 months.
Support
If you have any questions regarding your product, please do not hesitate to
contact us at care@rexingusa.com, or call us at
877-740-8004. Queries are typically
answered within 12-24 hours.
Your opinion matters
Rexing is firmly committed to always improving our products, services, and
user experience. If you have any thoughts on how we can do even better, we
welcome your constructive feedback and suggestions.
Connect with us today at care@rexingusa.com
Thank you for choosing Rexing!
FCC ID: 2AW5W-V1PGW
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
MADE IN CHAINA
Documents / Resources
|
ReXING V1PGW-4K Dual Channel Car Dash Cam
2160p
[pdf] User Manual
V1PGW-4K, Dual Channel Car Dash Cam 2160p, Car Dash Cam, Dash Cam
---|---
|
REXING V1PGW-4K Dual Channel Car Dash
Cam
[pdf] User Manual
V1PGW-4K Dual Channel Car Dash Cam, V1PGW-4K, Dual Channel Car Dash Cam, Car
Dash Cam, Dash Cam
References
- Rexing USA | Your Roadside Eyewitness
- Rexing Dash Cam (@rexingdashcam) • Instagram photos and videos
- Product Support | Rexing USA
- Rexing Product Reg II | Rexing USA
- Videos | Rexing USA