Profi Care PC-VL 3069 LB Standing Fan with Humidifier Instruction Manual

Profi Care PC-VL 3069 LB Standing Fan with Humidifier

Instruction Manual

Thank you for choosing our product. We hope you will enjoy using the appliance.
Symbols in this Instruction Manual
Important information for your safety is specially marked. It is essential to comply with these instructions in order to avoid accidents and prevent damage to the appliance:

WARNING:

This warns you of dangers to your health and indicates possible injury risks.

CAUTION:

This refers to possible hazards to the appliance or other objects.

NOTE:

This highlights tips and information.

General Notes

Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the internal packing. If you give this appliance to other people, please also pass on the operating instructions.

•  The appliance is designed exclusively for private use and for the envisaged purpose. This appliance is not fit for commercial use.
•  Do not use it outdoors. Keep it away from sources of heat, direct sunlight, humidity (never dip it into any liquid) and sharp edges. Do not use the appliance with wet hands. If the appliance is humid or wet, unplug it immediately.
•  When cleaning or putting it away, switch off the appliance and always pull out the plug from the socket (pull the plug itself, not the lead) if the appliance is not being used and remove the attached accessories.
•  Do not operate the appliance without supervision. If you  leave the room you should always turn the appliance off. Remove the plug from the socket.
•  The appliance and the mains lead have to be checked regularly for signs of damage. If damage is found the appliance must not be used.
•  Use only original spare parts.
•  In order to ensure your children’s safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.

WARNING:

Do not allow small children to play with the plastic foil. There is a danger of suffocation

Special Safety Precautions for this Appliance

Disconnect the appliance from the mains supply when refilling
with water or during cleaning.

CAUTION:

• The integrated humidifier works by ultrasound. This sound may be disturbing to pets.
• Do not place the appliance directly next to heating appliances or electrical appliances.
• Do not scratch the ultrasound probe.
• Never stick fingers or other objects through the protection grid.
•  Watch out for long hair! It can be caught in the fan owing to the air turbulence!
• Use the appliance only with the protection grids on!
• If you need to remove the fan guard, first switch of the appliance and disconnect the mains plug.
• Select a stable base to avoid the tipping of the fan during use!
• Do not place the appliance immediately next to stoves or other sources of heat.
• Do not repair the appliance by yourself. Always contact an authorized technician. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge
• if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• Do not immerse the appliance into water for cleaning. Please follow the instructions as stipulated in the chapter “Cleaning”.

Unpacking the Appliance

1.  Remove the appliance from the package.
2.  Remove all packaging material such as films, filler, cable holders and cardboard.
3.  Check the delivery contents for completeness.
4.  Should the package contents be incomplete or damages be found, do not take the appliance into operation. Take it immediately back to the dealer.

NOTE:

Dust or production residues can be located on the appliance. We recommend to clean the appliance as described under “Cleaning”.

Overview of the Components / Scope of Delivery

1. Hook

2. Fastening hooks

3. Propeller

4. Protection grid

5. Mounting screw M2,5*8 mm with nut

6. Switch housing

7. Stand tubes

8. Tube with tank cap

9. Water tank

10.  Humidifier base

11.  Stand with cover
    Page 4: Assembly Overview

12.  M5*18 mm screws (4 ×)

13.  Base (Base plate)

14.  Metal plate with mounting holes (1 ×)

15.  M5 nuts (4 ×)

16.  Cover of the stand (2 ×)

17.  M6*10 mm screws with nuts

18.  Motor

19.  Rear protection grid

20.  Nut for rear protection grid

21.  Attachment screw for propeller

22.  Front protection grid

Not Shown:

• Remote control
• ST4*25 mm screw for fastening the humidifier to the stand
• M6 nuts to fasten the motor to the stand tubes (2 ×)

Notes for Use

•  You can use this appliance to increase the air humidity in a dry environment. This offers the following benefits:
  • Provides a healthy indoor environment and is thus beneficial to your well-being.
  • Your skin does not dry out as readily.
  • Static in the air is eliminated.
•  The appliance works best if doors and windows are kept closed when used in mist mode.

Electrical Connection

1. Before inserting the plug into the socket. Make sure that the mains voltage to be used matches that of the appliance. You can find this information on the nameplate.
2.  Connect the appliance to a duly installed protective contact socket. The indicator lamp POWER shows that the power supply is connected.

Fitting Batteries into the Remote Control

(Batteries not supplied.)

1. Open the lid of the battery compartment on the rear of the remote control.
2.  Insert 2 MICRO batteries of type R03 “AAA“ 1.5 V.
3.  Please ensure the correct polarity. Details can be found in the battery compartment.
4.  Close the battery compartment.

NOTE:

If you are not going to use the remote control for a prolonged period, remove the batteries in order to prevent them from leaking.

CAUTION:

•  Used batteries should not be disposed of in the domestic waste. Please return all batteries to a special collection point. Your local authority will provide you with information on this.
•  Different types of battery or new and used batteries must not be used together.

Remote Control Range

• The remote control has a range of ca. 8 meters. If this range becomes shorter, the batteries must be changed.
• To use the remote control, point it at the sensor on the front of the switch housing.
• Make sure there are no obstacles between the remote control and the sensor.
• The angle of the remote control to the remote control sensor should not exceed 30 ° to the right, left, up, and down.

Position
The ideal position is a non-slip, flat surface

Assembly Instructions

The appliance must be fully assembled before use! We recommend that you refer to the figures „Overview of the Components“ and „Assembly overview“ when assembling

Base Unit (Fig. a – c)

1.  Screw the tubes (7) onto the stand (13). Use the four screws (12), the metal plate (14), and the four nuts (15).

2.  Attach the cover of the stand (16) to the stand tubes
   NOTE:
   The nuts and screws (17) are preinstalled on the rear of the switch housing.

3.  Check if the screws (17) possibly have been screwed into deeply. In this case, turn the screws back a little. Do not screw them out all the way!

4. NOTE:

• f a screw or a bolt should have dropped off, proceed as follows:
•  Hold the preassembled unit (motor (18), switch housing (6), and humidifier base (10)) so that the motor points down.
• Insert one nut (M6) each into the shaft at the side of the recesses for the tubes.
• Screw the two screws (17) on the rear of the switch housing lightly into the nuts.

1. Set the preassembled unit for a depth of approximately 3 cm onto the stand tubes.
   NOTE:

2. The humidifier cable must be routed between the two tubes.

3. Secure the preassembled unit to the stand tubes by

4. tightening the two screws (17).

5. Fasten the base of the humidifier (10) with the large screw (ST4*25 mm) to the base of the stand. For this, insert the screw from below through the stand and its cover into the small outer bore (Fig. on the right).

6. Fan (Abb. d)

7. Remove the preinstalled nut (20) from the motor (18). Keep it close to hand.

8. Align the rear protection grid (19) with the motor recesses (18).
   NOTE:
   The handle must point upwards

9. Tighten the nut (20) for the rear protection grid clockwise.

10. Attach the propeller (3). When doing so, use the guide pin on the motor shaft.

11. Tighten the screw (21) for the propeller anti-clockwise

12. Remove the prefitted screw and nut (5) from the front protection grid (22). Keep it close to hand.

13. Open the fastening hooks (2) at the front protection grid.

14. Attach the front protection grid by engaging the groove of the hook (1) with the rear protection grid
    NOTE:
    The holes for the screw (5) in the front and rear protection grid must be aligned.

15. Secure the protection grid with the screw and the nut (5).

16. Close the four fastening hooks (2).

17. Humidifier (Fig. e – f )

18. The tube already may have been installed on the switch housing. In this case, continue the assembly from item 18.

19. Feed the tube (8) from front to back between the two stand tubes (7). Then insert the tube from the bottom upwards through the opening on the underside of the switch housing (6).
    NOTE:
    The end of the tube with the tank cap must be positioned at the front above the humidifier.

20. Insert the tube from the back to the front through the opening on the top of the switch housing.

21. Pull the tube tight so that it lies flat against the back of the switch housing.
    NOTE:
    The two ends of the tube should have approximately the same length.

22. Connect the top end of the tube to the tube connector on the protection grid (22).
    NOTE:
    The tube above the switch housing must not “sag”. Water which accumulates in the tube prevents the formation of the mist. If necessary, push back the top section of the tube.

23. Place the water tank (9) onto the base of the humidifier (10).

24. Fit the tank cap on the bottom end of the tube onto the water tank. The recess on the tank cap must fit into the groove on the opening to the water tank.
    NOTE:

25.  The tank cap on the end of the tube can be turned.

26.  The water tank must be fitted securely to the base so that mist cannot escape between the water tank and the base. If necessary tighten the lower section of the tube.

Operation

Fill with Water

CAUTION:

Do not fill the water tank with water from clothes dryers and water with additives (such as scented oils, perfume, softeners, or other chemicals). Doing so may damage the appliance.

NOTE:

•  Only use distilled or boiled, cold tap water without additives.
• Replace the water every 3 – 4 days, even if it has not yet been used.
• If the appliance has not used for long periods, remove the water from the water tank and from the base of the humidifier.
•  Pull the end of the tube with the tank cap out of the water tank.
• Lift the tank from the base of the humidifier and turn it over. The filling hole is located on the bottom of the tank.
• Turn the tank cap and fill the water up to ca. 1 centimeter below the rim. The tank holds around 3 litres.
• Close the cap again and place the tank back onto the base.
•  Place the end of the tube with the tank cap onto the water tank.

NOTE:

Take note of the recess on the tank cap (see assembly instruction, item 21).

Basic Settings

Set the blower inclination angle before starting the appliance. You can adjust the inclination angle by tipping the blower casing with both hands.

NOTE:

• The inclination angle amounts to approx. 10 °.
• The tube above the switch housing must not “sag” due to the inclination of the blower. Water which collects in the tube prevents the formation of mist.

You can operate the appliance using the remote control as well as the buttons on the switch housing. The functions are identical.

NOTE:

The LED´s on the switch housing indicate the settings

ON / OFF Switch ON / OFF
Use the ON / OFF button to switch the appliance on or off.

NOTE:

•  When switching on for the first time after you have connected the mains plug to the mains outlet, the fan works in NOR (normal) mode with a low speed (LO).
• After switching off and on again using the ON / OFF button, the appliance continues working in the last set mode.

SPEED Speed
Press the SPEED button to select one of the three different
speeds:

•  LO low
• MI medium
• HI high

TIMER Timer
If you want the timer to switch tfh, e praepspsl ia

TIMER button

NOTE:

Every press of the TIMER button increases the operating time by 30 minutes. Maximum shut-off time: 7.5 hours.

MODE Wind Change Functions

The appliance has the two special functions: NAT (NATURE) band SLE (SLEEP). The speed of the fan buries between the functions.

Press the MODE button to switch these functions on.

NAT Natural Mode

• If the HI (high speed) setting is selected, the speed alternates between high– medium – low – off.
• If you have selected MI (medium speed), the speed alternates between medium – low – off.
• In the LO (low speed) setting, the speed alternates between low – off.

SLE Sleep Mode

•  If HI speed is set: The fan works in the first 30 minutes as in “Natural Mode” at the HI speed setting. In the subsequent 30 minutes the fan works as in “Natural Mode” at the set MI speed. For the remaining time the fan works as in “Natural Mode” at the speed setting LO.
• If MI speed is set: The fan works for the first 30 minutes as in “Natural Mode” at the speed setting MI. For the remaining time the fan works as in “Natural Mode” at the speed setting LO.
• If LO speed is set: Switching between low speed and shut-off of the fan as in “Natural Mode”. NOR Normal
• Select the NOR (NORMAL) function to return to normal operation.

OSC Oscillation

•  If you select the OSC function the appliance oscillates automatically through a range of approx. 60 degrees.
• In order to switch the function of, press the OSC button again.
•  If you select the OSC function the appliance oscillates automatically through a range of approx. 60 degrees.
• In order to switch the function of, press the OSC button again.

MOIST Mist

• The humidifier can be switched f onr egaarnddle sso f of the
  fan mode.
  Press the MOIST button to select the intensity of the mist:

•  LO low

•  MI medium

•  HI high
  To deactivate the function, press the MOIST button again.

Refill Water

When you want to refill the tank:
1. Switch off the appliance.
2. Disconnect the plug from the mains.
3. If necessary, pour the remaining water out of the tank.
4. Proceed as described under “Fill with Water”.

Shutting Off

If you want to shut off the fan:
1. Switch off the appliance.
2. Disconnect the plug from the mains.
3. Empty the water tank and the base of the humidifier if you do not plan to use the appliance for a lengthy period.

Cleaning

WARNING:

•  Always remove the mains plug before cleaning the appliance.
•  If you need to remove the protection grid: Always switch the
• appliance of and remove the mains plug.
•  Under no circumstances should you immerse the appliance in
• water for cleaning purposes. Otherwise this might result in an
• electric shock or fire.

CAUTION:

•  Do not use a wire brush or any abrasive items.
•  Do not use any acidic or abrasive detergents.

Housing

• Clean the outside of the appliance with a dry cloth without any additives.
• If the appliance is very dirty wet a cloth with water and then wipe the appliance dry once you have finished.

Water Tank

• Rinse the tank with clean water.
• Allow the tank to dry before closing it again.

Humidifier Base

•  Clean the area on which the water tank rests once a week.
• Wipe the area with a damp cloth.
• If necessary, use a few drops of white vinegar and let it act for ca. 5 minutes.
• Then wipe the area clean again.
• Stubborn dirt can be loosened with a nylon brush.

Decalcification

The frequency of the decalcifying operation depends on the hardness of the water and on how often the appliance is used.

• f the tank is very dirty, add ca. 100 ml of white vinegar to the cleaning water.
• Leave the solution in the tank for ca. 10 minutes.
• Rinse out the water tank with clean water.

Troubleshooting

The POWER LED and one of the MOIST LED´s (LO / MI / HI) are lit, but no mist is being produced.| The water tank is empty.| Fill the water tank.
Not enough mist is being produced.| Water has collected in the tube under- neath the switch housing| Push the top section of the tube back so that the water cannot accumulate.
The humidifier is dirty.| Clean the humidifier.
The water is dirty.| Change the water.
Mist or water escapes between the

water tank and the humidifier base.

| The bottom section of the tube is too

short.

| Pull back the bottom section of the tube so

that the water tank fits securely on the base.

There is a bad smell.| The water is too old or dirty.| Change the water and clean the humidifier.

Technical Data

• Model:…………………………………………………….PC-VL 3069 LB
• Power supply:……………………………………. 220 – 240 V~, 50 Hz
• Power consumption: ……………………………………………….85 W
• Protection class: ……………………………………………………………
• Net weight: …………………………………………….. approx. 3.60 kg

The right to make technical and design modifications in the course of continuous product development remains reserved.
This appliance has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and is manufactured according to the latest safety regulations.

Disposal

Meaning of the “Dustbin” Symbol

Protect our environment: do not dispose of electrical equipment in the domestic waste. Please return any electrical equipment that you will no longer use to the collection points provided for their disposal.

This helps avoid the potential effects of incorrect disposal on the environment and human health. This will contribute to the recycling and other forms of re-utilisation of electrical and electronic equipment. Information concerning where the equipment can be disposed of can be obtained from your local authority.

Internet: www.proficare-germany.de
Made in P.R.C.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>