PROFI CARE PC-PSM 1031 Pepper and Salt Mill Set Instruction Manual

PROFI CARE PC-PSM 1031 Pepper and Salt Mill Set

Thank you for choosing our product. We hope you will enjoy using the mill. Our products undergo continuous quality testing

NOTE:
Slight contamination due to pepper or salt remains are caused by quality testing and are unavoidable.

Symbols in these Instructions for Use
Important information for your safety is specially marked. It is essential to comply with these instructions in order to avoid accidents and prevent damage to the machine:

WARNING:
This warns you of dangers to your health and indicates possible injury risks.
CAUTION:
This refers to possible hazards to the machine or other objects.
NOTE:
This highlights tips and information.

Safety Information

Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the internal packing. If you give this device to other people, please also pass on the operating instructions.

• The device is intended exclusively for private and not for commercial use.
• Do not use the appliance if it is damaged.
• Do not repair the device yourself, but rather consult an authorised expert.
• Use the device only for the intended purpose.
• Keep away from heat, direct sunlight, dampness (never immerse in fluids), and sharp edges.

Included in delivery

One pack contains 2 pepper/ salt mills.

Preparation

Symbols

• Mill open
• Mill closed

Remove the mill body

1. Give the body one short turn anti-clockwise.

2. Remove the body by pulling it up.
   Insert batteries (Batteries not included)
   WARNING:
   Risks when handling batteries!

   • Do not expose the batteries to high temperatures or direct sunlight.
   • Never throw batteries into the fire. There is a danger of explosion!

3. Pull the plastic sleeve from the battery compartment.

4. Insert 4 identical type batteries of MIGNON/ AA/R6 type into the battery compartment. Observe the correct polarity of the batteries when inserting.

5. Reattach the plastic sleeve to secure the batteries.

6. Separate the motor part from the storage
   chamber. Pull it out upwards.

7. You can fill the storage chamber with pepper
   corns or salt grains.

8. Put the motor part back onto the storage
   chamber.

   • Place the drive of the motor part onto the shaft in the storage chamber.
   • The contact pins need to sit precisely on the contact screws of the storage chamber so that the current can be transmitted to the lamp.
     Close the housing

9. On the body and the storage chamber, you will find symbols.

   • Position the housing body so that the arrow points to the symbol on the storage container.
   • Give the housing body one short turn in a clockwise direction

10. Turn the wingnut on the bottom of the mill

    • clockwise, to grind the grain/corn finer.
    • anti-clockwise to grind the grains/corns coarsely.

Operation

To grind the grains, press the switch on the top side of the mill. The lamp will light up.
Whilst not in use
If the unit is not used for long periods of time, remove the batteries to avoid “leakage” of battery acid.

Cleaning

CAUTION:

• Do not immerse the balance appliance in water: the electronic components can be damaged.
• Do not use a wire brush or any abrasive items.
• Do not use any acidic or abrasive detergents.

1. Clean the device with a slightly moist cloth. Make sure that no humidity or waters seeps into the device!
2. Dry the device well after cleaning with a dry and soft cloth.

Storage

• Clean the device as described and allow to dry completely.
• We recommend that you keep the appliance in its original packaging if the appliance will be not used for long periods.
• Always keep the appliance out of the reach of children in a dry, well-ventilated place.

Troubleshooting

The unit does not work
Possible cause:
The body of the mill is assembled incorrectly.
Action:
Check that the body is assembled correctly:

• The drive of the motor part needs to sit precisely on the shaft in the storage chamber.
• The contact pins need to be placed precisely on the contact screws on the storage chamber.
• The arrow on the housing body must point to the symbol.

Possible cause:
The batteries are spent.
Action:
Change the batteries. Use 4 new MIGNON/AA/R6 type batteries.

Blocked grinding mechanism

1. Turn the mill with the wingnut facing upwards.
2. Unscrew the wingnut slightly by turning it anticlockwise.
3. Push the switch until the grinder disengages.
4. Adjust the desired grinding grade.

Technical Dat

• Model: ………………………………………..PC-PSM 1031
• Power supply:…. 4 batteries 1.5 V Type “AA” / “R6”
• Net weight: ……………………………………………0.39 kg

The right to make technical and design modifications in the course of continuous product development remains reserved. This device has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations.

Disposal
Meaning of the “Wheelie Bin” Symbol Remove the batteries before disposing of the appliance. Take care of our environment, do not dispose of electrical appliances via household waste. Dispose of obsolete or defective electrical appliances via municipal collection points. Please help to avoid potential environmental and health impacts through improper waste disposal. You contribute to recycling and other forms of utilization of old electric and electronic appliances. Your municipality provides you with information about collecting points.

Internet: http://www.proficook.de

References

• Proficook Startseite

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>