KAWA S7 Baby Camera User Manual

KAWA S7 Baby Camera

Box Contents

Monitor Features

1 2 Volume-/+Keys
3 Menu Button:

1.  Short press the [Menu] to pop up the menu.
2. Short press the [Menu] to close the menu and return to the home page
3. When the camera is recording, press the [menu] key for 2 seconds to stop recording; When the camera with a micro SD card inserted and there is no video recording, press the [menu button for 2 seconds to start video recording.

4 OK Key:

1. Click the [OK] button to enter the Camera Setting in the disconnected interface.
2. For function selection, press the [OK] key to confirm the selection.
3. When connecting multiple cameras and the monitor is in multi-screen display mode, press the [OK] button for 2 seconds to switch the monitoring screen.

5 6 7 8 Navigation Buttons
Return to the previous level of the menu/Talk button:

1. Short press the[ return menu /Talk intercom] button in the menu bar and return to the superior menu.
2. Any interface, long press [return to the last menu/ Talk intercom button to achieve voice intercom.

10 Power Button:
Long press for 3 seconds to power on / off, short press to switch on/off the monitor screen

• 11 Press the button switch among zoom 1.5X, zoom 2X, and zoom off.
  Hold the button: take a picture and save it to the memory card.

• 12 Monitor LED Indicator (Red: In Charging Green: Full Power)

• 13 Monitor TYPE-C Port

• 14 Display Screen

• 15 Microphone

• 16 Reset Button

• 17 Support Stand

• 18 Speaker

Camera Features

1. Wide-Angle Lens
2. Microphone
3. Micro SD Card Slot
4. Camera Power LED Status Indicator
5. Camera Antenna
6. Speaker
7. Temperature Sensor
8. Camera Micro USB PortCamera Pairing Button

Monitor Charging Method

Please fully charge the Monitor before using it. Charging method:

1. Connect one end of the TYPE-C(1m) cable to the Baby Monitor, and the other end to the power adapter (5V 2A).
2. Plug the adapter into a power outlet.

Camera Power Supply Method

1. Connect one end of the Micro USB (2.6m) cable to the camera and the other end to the power adapter (5V 1A).
2. Plug the adapter into a power outlet.

After powering the Camera and fully charging the Monitor, you can enjoy the video baby monitor.

Camera Installation Methods

Install Camera( wall mount & corner mount)

1.  Determine the installation position.
2. Put the upper wall bracket on the mounting position and mark the screw hole with a pencil.
3. Drill the hole 06.0 mm on the wall, then insert the expansion nail into the hole.
4. Screw through the mounting hole of the upper wall bracket and screw into the expansion nail.
5. Align the Camera on the upper wall bracket, push forward and hold the Camera.

Note: Please make sure the Camera is properly installed and secured.

Add Camera to the Baby Monitor

Baby Monitor and Baby Camera are paired out of the box. Please refer to the following steps when adding additional Baby Cameras or after resetting a Baby Camera:
Please make sure the Baby Monitor and the Baby Camera match the same version.

1. Press the [MENU]J button to open the menu, select “Camera Settings””Camera Pairing”, and press [OK] to add Camera.
2. Press the pair button on the back of the Camera for seconds until you hear the ticking prompt.

Display Mode of Screen

When you add more than two Baby Cameras, you can manually and automatically switch the camera screens.

1. Manual switching: Long press the [OK] button, and the screen will be switched to the next screen. The icon of the camera you select will display.
2. Automatic switching (Muti-Camera Cycling): select “Camera Settings” “Display Mode” and “Muti-Camera Cycling/”option. The screen cycles through the list of connected Baby Cameras according to pre-set intervals.

Full Screen
This mode allows you to see one camera in full-screen view.

Monitor Menu Settings & icons Description

Menu settings

Press the [MENU] button on the Monitor to display the functional interface, as shown below:

• Monitor Mode: VOX Mode When you turn on the VOX mode, the screen will be turned on automatically if the noise is detected above your pre-set level.
• VOX Threshold1-5 thresholds are optional.
• Audio Only: but you’ll hear audio from your camera(s). -Select “Audio Only”, monitor display turns off,

Alert:

• Sound Alert- You can set the Baby Monitor to alert you when a specific noise level is detected.
• Note: Surrounding noise might set off a false alarm.
• High Temp Alert When the temperature is higher than the value you set, the monitor will alert.
• Note: The high-temperature alert you set must be higher than the low-temperature alert you set.
• Low Temp Alert When the temperature is lower than the value you set, the monitor will alert.
• Note: The low-temperature alert you set must be lower than the high-temperature alert you set.
• Alert Duration-5 Secs, 10 Secs, 20 Secs and 30 Secs are optional. “10 Secs” by default. The monitor will alert continuously according to the alert duration you set.
• Alert Volume1-3 volumes are optional, “2” by default.
• Note: When the Monitor paired more Cameras if you set volume 1 which means all paired cameras are volume 1.

Lullaby

• Monitor white noise-Help parents sleep. Select your desired white noise. You can adjust the volume by pressing the “-/+” volume button.
• Cam era Lullaby- Comfort baby. Select your desired lullaby song. You can adjust the volume by pressing the “-/+” volume button.
• Note: Alert is automatically disabled after enabling the lullaby function.
• Warning: The sound of lullabies may mask the baby’s cry.

Clock Reminder

Feeding. Diaper Changing. Other
off, 1H, 1.5H, 2H, 2.5H, 3H, 3.5H, 4H and custom are optional.

Description:

1. “Off” indicates that the clock reminder is turned off.
2. “1H, 1.5H, 2H, 2.5H, 3H, 3.5H, 4H” means that the monitor will alarm you after 1, 1.5, 2, 2.5, 3, 3.5, 4 hours. (e.g. When you choose “Feeding” -> “3H”, means that the alarm clock will remind you to feed after 3 hours)
3. Custom: You can set the clock according to the time you need.

Camera Settings

• Camera Pairing-1. Add Camera (Note: You can add up to 4 cameras per baby monitor.) 2. Delete Camera Display Mode Full screen, cycle cameras.
• Note: When multiple cameras are connected and set to “cycle cameras”, the monitor will cycle through the list of connected baby monitors according to the pre-set interval.
• Video Screen Setting- “Normal” by default. When the camera is inverted for mounting, select the corresponding camera first, select “Rotate 180°”, and then press “OK” to complete the setting.
• Record Mode No Record, Cyclic Recording(when motion detected), Cyclic Recording
• Select No Record: it means that the video will not be recorded, and it won’t be stored on the micro SD card.
  Select Cyclic Recording(when motion detected): It means that recording starts when motion is detected. “Cycle” means that when the micro SD card fills up, the earliest videos will be gradually and automatically deleted to store the latest video.
  Select Cyclic Recording:it means that the video will keep recording circularly, no matter the motion is detected or not.

Small icons description

Warning Explain

STRANGULATION HAZARD: Cords can STRANGLE children.
Keep cords out of the reach of children (more than. 3ft (0.9m) away).

Certification

• Product Name: Baby Monitor
• Brand Name: KAWA
• Model Name: S7
• Manufacturer: KAWA ELECTRONICS COMPANY LIMITED Use the Baby Monitor in the environment with a temperature between-10°C and 50°C, otherwise, it may damage your Baby Monitor. It can be operating under 2000m.

Hereby, KAWA ELECTRONICS COMPANY LIMITED declares that the radio equipment type Baby Monitors S7 is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: www.kawa-in.com
This device complies with the radio interference
CE requirements of the European Community.

FCC Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Declaration Of Conformity

1. Please use the standard AC Power Chargers and Charging Cables.
2. Do not use the device in an environment where the temperature is too high or too low, and do not expose the device to strong sunlight or an environment that is too humid.
3. The suitable ambient temperature for S7-M and accessories is -10°C to +50°C.
4. The suitable ambient temperature for S7-C and accessories is -10°C to +50 C.
5. When charging, please place the device in a well-ventilated environment with normal room temperature. It is recommended to charge the device within the temperature range of 0°C~-45°C.

This product is designed and manufactured with high-quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health, and the environment. For more information on the disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

Warranty:12-month limited warranty
Manufacturer: KAWA ELECTRONICSs COMPANY LIMITED
Email: support@kawa-in.com
Web: www.kawa-in.com
Address: FLAT A 21/F CHEUNG LEE IND BLDG 9 CHEUNG LEE ST CHAI WAN HONG KONG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>