HYPERX 4402194C CloudX Stinger Core Wireless Gaming Headset User Guide
- June 14, 2024
- HYPERX
Table of Contents
HyperX CloudX Stinger Core
Wireless Gaming Headset
Quick Start Guide
Overview
ASwivel-to-mute microphone
B Status LED
C Power button
D Volume wheel
E USB charge port
F Pairing button
G Game/chat balance wheel
H USB charge cable
Charging
It is recommended to fully charge your headset before first use
| CHARGE STATUS | LED |
|---|---|
| Fully charged | Solid white |
| 15% — 99% battery | Breathing white |
| < 15% battery | Breathing red |
Power Button
Power on/off – Hold power button for 3 seconds
Mic monitoring
Short press power button to toggle mic monitoring on/off
Setup for Xbox Console Usage
Power on the Xbox console. Press the connect button on your Xbox Console. The Xbox logo on the console will start blinking- Power on the headset. Press and hold the pairing button for 3 seconds to enter pairing mode. The headset status LED will start blinking green
- The headset will connect to the Xbox Console
Volume Wheel
Scroll up or down to adjust volume level.
WARNING: Permanent hearing damage can occur if a headset is used at high
volumes for extended periods of time.
Game/Chat Balance Wheel
Scroll up or down to adjust mix between game audio and chat audio 
The game/chat balance
functionality operates independently from the overall headset audio volume
Swivel to Mute Microphone
Questions or Setup Issues?
Contact the HyperX support team at
hyperx.com/support
Overview
A – Swivel to mute microphone
B – Status LED
C – Power button
D – Volume wheel
E – USB charge port
F – Pairing button
G – Game/chat balance wheel
H – USB charge cable
Charging
It is recommended to fully charge your headset before first use
| CHARGE STATUS | LED |
|---|---|
| Fully charged | Solid white |
| 15% — 99% battery | Breathing white |
| < 15% battery | Breathing red |
Power Button
Power on/off – Hold power button for 3 seconds
Short press power button to toggle mic monitoring on/off
Setup for Xbox Console Usage
-
Power on the Xbox console. Press the connect button on your Xbox
Console. The Xbox logo on the console will start blinking -
Power on the headset. Press and hold the pairing button for 3 seconds to enter pairing mode. The headset status LED will start blinking green
-
The headset will connect to the Xbox Console
Volume Wheel
Scroll up or down to adjust volume level.
WARNING: Permanent hearing damage can occur if a headset is used at high
volumes for extended periods of time.
Game/Chat Balance Wheel
Scroll up or down to adjust mix between game audio and chat audio The
game/chat balance functionality operates independently from the overall
headset audio volume
Swivel to Mute Microphone Questions or Setup Issues?
Contact the HyperX support team or see the user manual at
hyperx.com/support
Simplified Declaration of Conformity
Hereby, HP declares that the radio equipment is in compliance with Directive
2014/53/EU. The full text of the EU Declaration of Conformity is available at
the following internet address:
www.hp.eu/certificates (search with Model
Name) UK only: Hereby, HP declares that the radio equipment is in compliance
with the relevant statutory requirements. The full text of the declaration of
conformity is available at the following internet address:
www.hp.eu/certificates (search with Model
Name)
Battery/TX Power Info
Battery Information
Contains 3.7V, 1000mAh Li-ion Battery, 3.7Wh
Cannot be replaced by user
Frequency & TX Power Information
Frequency Bands: 2.4GHz/5GHz (TX Power: ≤ 8dBm)
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit diffierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the part
responsible for compliance could void the user’s authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available. FCC ID: B94-CS005
Canada Notices
This Class B digital apparatus complies with Canadian ICES-003.
Avis Canadian
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Industry Canada statement
This device contains licence-exempt transmitter(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
- this device may not cause interference,
- this device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure Information and Statement
The SAR limit of Canada is 1.6 W/kg averaged over one gram of tissue. This
device has also been tested against this SAR limit. The highest SAR value
reported under this standard during product certification for use properly is
0.013 W/kg.
Wireless Headset Model
©Copyright 2022 HyperX and the HyperX logo are registered trademarks or
trademarks of HP Inc. in the U.S. and/or other countries. All registered
trademarks and trademarks are property of their respective owners.
References
- Support – HyperX ROW
- Support – HyperX ROW
- Laptop Computers, Desktops, Printers, Ink & Toner | HP® Australia
- Regulations Certificates | HP® United Kingdom
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>