348A-L25 FOTRIC Thermal imager User Manual

Quick Start Manual

Fotric 34A Series/34 M Series

*stands for 1~9 numbers

Legal Disclaimer

1.1 Legal Disclaimer

Uncooled thermal imaging manufactured by FOTRIC are entitled to 1-, 2-years warranty (depending on the specific model) from the date of initial purchase and delivery. Warranty covers defects caused by materials and production processes, provided that such products are handled under normal storage, use, and repair conditions and in accordance with FOTRIC instructions.

Products not manufactured by FOTRIC but included in the system that FOTRIC sells to the original purchaser are covered by the specific supplier’s warranty terms (if any) and FOTRIC is not liable for those products. This warranty is provided to the original purchaser and is not transferable. This warranty does not apply to any product that has been damaged by misuse, neglect, accident, or abnormal operating conditions. Consumable parts are not covered by this warranty.

Any defects in the products covered by this warranty must be reported and the product must not be used to prevent further damage. The purchaser must report any defects to FOTRIC immediately, otherwise this warranty will not apply.

If the product is proven defective in relation to materials or manufacturing after FOTRIC’s inspection, it is up to the user whether it is to be repaired or replaced, provided that the product must be returned to FOTRIC within 3 Months from above mentioned report date. FOTRIC has no obligation or liability for any defects other than those mentioned above This product is exempt from any other warranties, expressed or implied FOTRIC hereby disclaims any implied warranties of merchantability and applicability for a particular purpose. FOTRIC is not responsible for any direct, indirect, special, incidental or consequential loss or damage based on contract, civil, or any other legal theory. This warranty clause shall apply the relevant provisions of the laws of the People’s Republic of China. Any dispute or claim arising out of or related to this warranty shall be finally settled through arbitration in accordance with the rules of the Shanghai Pudong New District People’s Court of the People’s Republic of China. The place of arbitration shall be Shanghai.

1.2 Usage Statistics

FOTRIC reserves the right to collect anonymous usage statistics to help maintain and improve the quality of the software and services provided.

1.3 Copyright

No parts of this software (including source code) may be reproduced, transmitted, transcribed, or translated into any kind of language or computer language in any form or by electronic, electromagnetic, optical, manual ways, or any other means without the prior written permission of FOTRIC.

No parts of this document may be reproduced, photocopied, reprinted, translated, or transmitted to any readable electronic medium or machine without the prior written consent of FOTRIC.

The names and logos shown on the products herein are either registered trademarks or trademarks of FOTRIC and/or its affiliates. All other trademarks, trade names or company names referenced herein are for identification purposes only and are the property of their respective owners.

1.4 Quality Assurance

The quality management system for the development and production of these products in FOTRIC has been certified in accordance with the ISO 9001 standard.

FOTRIC is committed to a policy of continuous development, so we reserve the right to modify or improve any product without prior notice.

1.5 Export Control

Thermal imaging products are listed as export-controlled products by the U.S. Department of Commerce, United Nations Security Council (UNSC), and European Union (EU). This product contains a focal plane array and cannot be used in controlled countries (such as North Korea, Iran, Syria, Cuba, Sudan, Russia, etc.), so please do not bring this product into or used in controlled countries. Any loss or liability arising from the above actions will be borne by you.

Safety Information

This product complies with the restrictions for Class A digital equipment in Chapter 15 of the FCC Rules. These restrictions are designed to prevent harmful interference to civilian installations. If not installed and used in strict accordance with the instructions, this equipment will generate, use and emit radio frequency energy, which may cause harmful interference to radio communications.

Definition

Warning > Represents a hazardous situation or behavior that could result in personal injury or death.

Caution > Represents conditions or actions that could result in damage to the instrument or permanent loss of data.

Notice > Represents useful information for users.

Important information

Please read before using the equipment :

Warning > This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning > Do not disassemble or do a modification to the battery of the thermal imager. The battery contains safety and protection devices, which, if damage occurs, can cause the battery to become hot, or cause an explosion or an ignition. If there is a leak from the battery and you get the fluid in your eyes, do not rub your eyes. Flush well with water and immediately get medical care. The battery fluid can cause injury to your eyes if you do not do this.

Warning > The thermal imager is equipped with a laser pointer. Do not look directly into the laser beam. The laser beam can cause eye irritation.

Caution > The thermal imager uses a very sensitive thermal sensor, do not point the infrared camera (with or without the lens cover) at strong energy sources, for example, devices that cause laser radiation, or the sun. This can have an unwanted effect on the accuracy of the camera. It can also cause damage to the detector in the camera.

Caution > Original packing box must be used during transportation. Please do not strongly hit the thermal imager during use and transportation.

Caution > When storing the thermal imager, it is recommended to use the original packing box and place it in a cool and dry place, away from strong electromagnetic field.

Caution > Please avoided oil and various chemical substances to contaminate or damage the surface of the lens. Please cover the lens with cap after use.

Caution > Do not use the camera in temperatures higher than +50°C (+122°F), unless other information is specified in the user documentation or technical data. High temperatures can cause damage to the camera.

Caution > In order to prevent potential risk of data loss, please copy (back up) the data to a computer periodically.

Caution > Please do not open the thermal imager’ s shell or modify it without permission. Repair services can only be performed by authorized FOTRIC personnel.

Notice > After the thermal imager is turned on, it may take about 5-10 minutes to warm up before accurate measurement.

Notice > Every thermal imager’ s temperature correction has been performed before delivered from factory.

Notice > To avoid potential hazards, Please do not use any batteries, chargers and charging docks which are not specified by the manufacturer.

The device does not support simultaneous Wi-Fi 5G and Wi-Fi 2.4G and BT, because the Wi-Fi 5G and Wi-Fi 2.4G and BT share the same antenna and can’t transmit simultaneously. There is not simultaneous transmission possibility.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Thermal Image

Front View

1. Laser Label
2. Speaker
3. Gallery Button
4. Back Button
5. AI Programmable Key
6. Microphone
7. Laser Button
8. Power Button
9. Touch Screen
10. Status Lamp

Rear View

1. LED Flash Light

2. Visual Light Camera
   (Pixel: 13 Megapixels)

3. Autofocus Button*

4. Battery

5. Freeze and Capture Button

6. Threaded hole for Tripod

7. Lens Cap

8. Laser distance meter*

Instructions:

• Limited to specific models, see product parameters for details.

Right View

1. Infrared Lens

2. Wrist Strap Bracket
   Fixing Point
   (left and right sides)

3. Wrist Strap Bracket
   Fixing Point
   (left and right sides)

4. Power Supply Interface

5. USB Type-C Interface

6. Micro HDMI Interface

Left View

1. SD Storage
   Card Interface

2. Wrist Strap Bracket
   Fixing Point
   (left and right sides)

3. Focus Ring

Main Accessories

The documentation shall indicate that only accessories which meet the manufacturer’ s specifications shall be used.

Power adaptor

Model No.: ABT030120A
input:100-240V ~50/60Hz 1.5A
output: 12V dc 3.0A

Battery charging dock

Part No.: F900001ACC
12V dc 3.0A

Batteries

Lithium-ion rechargeable batteries (7.4V, 3500mAh) 18Wh
Model No.: F900002ACC
Operation temp: -20~50 °C

USB cables

USB type-C type; conforms to USB 3.0 / 2.0 specification, supports USB OTG;
USB 3.0 has a maximum speed of 5Gbps; USB 2.0 supports a maximum speed of 480Mbps, and is downward compatible with full speed (12Mbps) mode

HDMI cables

Micro HDMI type,Comply with HDMI 1.4 specification, support 1080p image video transmission at 60Hz frame rate

Anti-interference magnetic ring

User Guide: The two snap on type magnetic rings shall be buckled mounted at both ends of HDMI cable respectively, and the position shall be close to the cable inlet and outlet as close as possible, which distance shall not be more than 50mm.

Laser distance Ranger and laser pointer

1. General

The laser distance ranger consists of a laser transmitter and a laser receiver. The laser distance ranger determines the distance to a target by measuring the time it takes for a laser pulse to reach the target and return to the laser receiver. This time is converted to a distance, which is displayed on the screen.

The laser receiver also works as a laser pointer. When the laser distance ranger is on, you will see a laser dot approximately at the target.

2. Laser warning label

A laser warning label with the following information is attached to the camera:

3. Laser rules and regulations

Wavelength: 635 rim. Maximum output power: 1 mW.

This is Class 2 Laser Product.

Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019.

Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Interface Introduction

Main Menu

(1) Status Bar
Display reminder icons such as battery, Wi-Fi, low SD card capacity, laser warning, time, logo, G PS, etc.

(2) Measurement Result Table
Display overall and area temperature, emissivity, and other values.

(3) Palettes and Temperature Scale Display
Display the color band of the palette, and the upper and lower limits of the temperature scale.

(4) Image Display
Display real-time thermal image, digital, PIP, image fusion , videos, measurement tool, and other values.

(5) System Menu
Enter temperature scale, temperature measurement parameters, image mode, ROI measurement tools, color palette, and settings.

(6) Temperature Measurement Parameters
Display emissivity reflected temperature, ambient temperature, relative humidity, distance and other parameters.

System Menu

(1) Temperature Scale
Auto temperature scale, Manual temperature scale, Touch scale settings.

(2) Temperature measurement parameters
Emissivity, reflected temperature, ambient temperature, relative humidity, target distance, infrared window compensation and other parameter settings.

(3) Image mode
Thermal image, digital camera, picture-in-picture, Thermal &digital camera fusion mode settings.

(4) ROI measurement tools
Add temperature measurement tools such as points, rectangles, circles, lines, etc., temperature rise and temperature difference, delete and display settings.

(5) Palette
Various palettes and inverted palettes, as well as color alarms (isotherms) and palettes.

(6) Settings
Capture mode, connection, temperature measurement range, storage and save options, device set.

Gallery

(1) Image display area
Display the thermal image photos, digital camera photos, full radiation thermal image video, non-radiation thermal image video thumbnails, click to select, long press for multiple choices.

(2) Filter favorite files
Only display files with selected favorite files.

(3) Filter tags
Filter by tags, and only display the filtered files in the Image Display Area.

(4) File analysis
Enter the Analysis mode to analyze the thermal photos and full-radiation video files.

(5) Delete
Delete selected files.

Settings

(1) Capture mode
Single frame capture, video recording and time lapse settings.

(2) Connection
WLAN, Hotspot, Bluetooth, FTP

(3) Temperature measurement range
Can be set to Intelligent range.

(4) Storage & Save Options
Settings such as super resolution, video format, saving digital camera file as a separate JPEG photo, and deleting all saved files.

(5) Device set
Settings for language, date & time and region, display settings, geographic location, screen-off time, manual adjustment mode, volume, reset, and information of thermal imager.

Quick Start

For quick start of the Thermal Imager, please follow the steps below:

1. Put a battery into the battery compartment of the thermal imager. (Before starting up the thermal imager for the first time, full charge the battery.)
2. Insert an SD storage card into the storage card slot.
3. Long Press the Power Button to turn on the thermal imager.
4. Aim the thermal imager toward the object of interest.
5. Press the Autofocus Button or adjust the Manual focus ring to get a clear image of the object.
6. Press the Capture Button to freeze the thermal image, so that it can be analyzed arbitrarily in this status.
7. Press the Capture Button again, the analyzed thermal image will be saved automatically.

For quick start of Fotric AnalyzIR PC software, please follow the steps

below:

1. Insert the USB disk, and copy the built-in AnalyzIR analysis software to PC.
2. Install AnalyzIR and relevant drivers on PC.
3. Start the AnalyzIR professional analysis software.
4. Use Type-C USB cable to connect the thermal imager to PC; or insert the SD card into the PC card slot; or use Wi-Fi FTP to transfer.
5. Copy the images in the Gallery folder in the SD card of the thermal imager to PC.
6. Open AnalyzIR, right-click the blank space in the quick collection bar of the AnalyzIR software, and select to add the thermal image files.
7. Click one or more thermal images to choose.
8. Analyze, save and generate reports.
9. Click to export the report as a Word document.

Note

• This equipment is intended to be used in utilities , energy, manufacturing, building diagnostics, and R&D.
• It is very important to adjust the focal length correctly. An Incorrect focal adjustment will affect the imaging clarity and measurement accuracy of the thermal imager.
• The thermal imager has a resolution limit, which depends on the detector size, lens, and distance to the object. If necessary, please move closer to the object. Stay away from hazardous areas or energized electrical components.
• Be careful when using the thermal imager perpendicular to the target, because you may become the main radiation source.
• Please choose a high-emission area (for example, an area with rough surface) for measurement.
• Blank objects (with low emissivity) are mainly reflected in the environment, so they may appear wrong result in the thermal imager.
• Various types of faults (such as faults that occur in building construction) may appear same type of heat distribution pattern.
• Analysis of the infrared images requires corresponding professional knowledge.

This manual may be inconsistent with the product due to function enhancement of the product or change of version, please always refer to the actual product.

Specifications

EN 61010-1:2010+A1:2019
Vibration| 2g (GB/T 2423.10-2008/IEC 60068-2-6:1995)
Shock| 25g(GB/T 2423.5-2019/IEC60068-2-27:2008)
EMC| EN 61326-1:2013 (immunity)
EN 61326-1:2013 Class A (emission)
FCC 47 CFR Part15 Class A (emission)
Drop| Engineered to withstand 2 meters (6.5 feet) drop with standard lens
Enclosure Rating| IP54 (protected against dust, limited ingress;
protection against water spray from all directions),GB/T 4208-2017/IEC60529:2013

Manuals Download

Before using the product, please visit the following website to read or download the user manuals:

FOTRIC 34A and 34M Series:
http://www.fotric.com/support-fotric340

AnalyzIR Download

PC analysis and report software AnalyzIR is a standard configuration of the product.
Please visit the following website to download:

http://www.fotric.com/support-analyzir

Appendix A

Emissivity Table

(For reference only)

Material Name|

Surface Condition

| Temperature (°C)|

Emissivity (ε)

---|---|---|---
Aluminum|

Non-oxidized

| 100| 0.20
Oxidized| 100|

0.55

Brass|

Polished brown

| 20| 0.40
Unpolished| 38|

0.22

Oxidized

| 100|

0.61

Copper|

Severely oxidized

| 20|

0.78

Iron|

Oxidized

| 100| 0.74
Rusty| 25|

0.65

Cast iron|

Oxidized

| 200| 0.64
Non-oxidized| 100|

0.21

Wrought iron|

Roughened

| 25| 0.94
Polished| 38|

0.28

Nickel|

Oxidized

| 200|

0.37

Stainless steel|

Oxidized

| 60|

0.85

Steel|

Oxidized at 800°C

| 200|

0.79

Common brick|

Surface

| 20|

0.93

Concrete|

Surface

| 20|

0.92

Glass|

Polished plate

| 20|

0.94

Lacquer|

White

| 100|

0.92

Natural color black

| 100|

0.97

Carbon|

Smoke black

| 25|

0.95

Candle soot

| 20|

0.95

Graphite rough surface

| 20|

0.98

Paint|

Average of 16 colors

| 100|

0.94

Emissivity Table

(For reference only)

Material Name|

Surface Condition

| Temperature (°C)|

Emissivity (ε)

---|---|---|---
Paper|

White

| 20|

0.93

Sand|

Surface

| 20|

0.90

Wood|

Polished

| 20|

0.90

Water|

Distilled water

| 20|

0.96

Skin|

Human

| 32|

0.98

Pottery|

Fine

| 21|

0.90

Abrasive

| 21|

0.93

Appendix B

Statement

Federal Communications Commission (FCC) Declaration of Conformity

Note:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Exposure to Radio Frequency (RF) Energy

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. And user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The mobile device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue.

The highest SAR value reported under this standard during product certification for use when properly worn on the body is 1.420 W/kg.

Innovation Excellence Integrity

Equipment described herein may require EU, US and UNSC authorization for export purposes.
Imagery for illustration purposes only.
Specifications are subject to change without notice.
FOTRIC INC. All Rights reserved.

Contact FOTRIC

CHINA                                             U S.
Lane 2500-14, Xiupu Road,              +1 (214) 235 4544
Pudong District, Shanghai,
P.R.China
+86 (21) 6698 1992

    info@fotric.com
     www.fotric.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>