SoundBot SB221 HD Wireless Bluetooth 4.0 Headset Sports-Active Headphone-Complete Features/User Guide

SoundBot SB221 HD Wireless Bluetooth 4.0 Headset Sports-Active Headphone

Specifications

• BRAND: Soundbot
• EAR PLACEMENT: Over Ear
• CONNECTIVITY TECHNOLOGY: Wireless
• BLUETOOTH: 4.0
• FORM FACTOR: Over-Ear
• CABLE FEATURE: Without Cable
• PRODUCT DIMENSIONS: 11.42 x 4.29 x 1.81 inches
• ITEM WEIGHT: 3.21 ounces
• AVRCP: 1.4 Profile
• HSP: 1.2 Profile
• HFP: 1.6 Profile
• STANDBY/TALK TIME: Up to 300hrs/25hrs
• PLAYBACK TIME: Up to 20hrs
• INPUT POWER: 5V
• 450MAH BATTERY: Rechargeable Li-Polymer
• ENVIRONMENT: OPERATING TEMP: -10C – +55C
• STORAGE TEMP: -20C – BOC

Introduction

It Features an ergonomic behind-the-ear and neck human engineering frame design that securely fits and comfortably sits over the ear/neck for both indoor and sports-active outdoor use with a range of up to 33 feet. It has 5 dedicated remote control buttons for simple navigation and rapid access to SIRI or Android voice commands (only on supported phone models and operating systems), call management, wireless audio streaming control, and volume changes. It has Noise cancellation, crystal clear audio technology, and a high-performance speaker driver reproduce and provide a natural and balanced full range music spectrum for enhanced HD listening experiences.

It contains Swivelable earcups with a tiny, water-resistant, ultra-foldable frame give optimal comfort and portability for everyday use. Scratch-resistant surface to avoid wear and tear on the headset. The device can play music, make phone calls, and watch videos for up to 25 hours without needing to be recharged.

PRODUCT FEATURES

CHARGE HEADSET FOR AT LEAST 2 HOURS

• - Volume Down / – >l•  Volume Up/+

• Red LED will light up when charging.
• Red LED will turn off once it’s fully charged.
• Be sure headset is powered off before going to next step.

PAIRING YOUR SB221 VIA BLUETOOTH

• In the power-off mode, press and hold the multifunction for 7-9 seconds until the LED alternately flashes between red and blue.
• Pair with your device via search/add new Bluetooth on the media device.
• The S8221 will beep as confirmation that the headset has paired with the media device
• If a PIN code prompts, enter 0000.

CONFIRM SUCCESSFUL PAIRING

Your device will show that SB221 is “paired.” Unsuccessful pairing:

1. LED may still be flashing red and blue, search on your device again for the new device.
2. If the paring is still unsuccessful, power down by pressing and holding down multi-function button for 4 seconds and then re-start from the previous step “Pair ng your SB221 via Bluetooth;’ or contact SoundBot at support@volcus.com for additional support.
3. SB221 will automatically exit pairing mode within 5 minutes of idle time or inactivity and shut down in another 5 minutes.

OTHER CONTROLS

• Mute/Unmute the microphone during a call: Press & hold – button for 3 seconds.
• Transfer calls between SB221 and the mobile phone: Press & hold the + button for 2 seconds.

VOICE COMMAND (ON SUPPORTED PHONE ONLY)

• Voice dialing for supported Siri or Android devices: Press both + & – buttons simultaneously, followed by an alert tone to indicate activation of the voice dialing function. Say the desired command or name from the phone contact list to dial.

GENERAL USE AND NOTICES

Please read the following information before using this product. Users are not permitted to make changes or modify the product and the accessories in any way.

1. Do not use the product while operating a motor vehicle.
2. To avoid electronic interference and/or compatible conflicts, TURN OFF the product in any facilities where posted notices instruct you to do so.

For example
Aircraft, Military bases, hospitals, or Health Care Facilities.

3. To avoid impairing your hearing in the long-term operation, keep the headset volume at a moderate level.
4. Keep away of fire, water, and high voltage equipment.
5. Follow the charging procedure described in this guide to charge the product.

CHARGING THE BATTERY

8B221 uses a rechargeable battery. A normal charging process takes about 2-3 hours. The red LED will turn off when charging is completed. When the battery is nearly used up, the red LED will flash twice every 15 seconds and there will also be a sound alert from the headset. Please re-charge the headset. Please make sure the battery has been fully charged for your first 3 uses to ensure the battery’s best performance.

Always use the correct AC Power Adapter to charge the headset. Using an incorrect power supply device will cause damage and void the warranty. Upon completion of charging, please unplug the charging cable from 8B221. Do not put and leave the headset in charging mode after it’s fully charged. This will shorten the lifetime of the battery. Do not use the headset in extreme weather conditions. It is recommended to keep the environment temperature between 15 and 25 degrees. Do not install, place or use the headset near any source of heat such as a stove, radiator, oven, toaster, coffee maker or other apparatus (including microwave oven) that gives off heat.

SAFETY INSTRUCTIONS

• Keep the unit away from extreme weather to protect the unit against electric shock, explosion, and/or bodily injury.
• Do not use the unit if it has been dropped or damaged in any way. Do not expose batteries or battery packs to excessive heat, such as direct sunlight or open flame.
• Keep the product out of reach of children. Do not use the headset at excessive levels as it may damage hearing.
• Do not puncture or disassemble the exterior surface of the product in any way.
• Keep the unit free from dust, lint, etc. Do not use this unit for anything other than its intended use or purpose. Do ng so may damage the device.

Frequently Asked Questions

• What is the procedure for pairing a SoundBot Bluetooth headset?
  Turn your phone’s Bluetooth on. Press and hold the power button on the SoundBot..
  I connected mine to my phone.
  Hold down the power button on your phone until the red and blue lights flash, then navigate to your phone’s Bluetooth settings to pair.

• What’s the best way to pair my SB221?
  Press and hold the multifunction for 7-9 seconds in the power-off mode until the LED alternates between red and blue flashing. Search/add new Bluetooth on the media device to pair with your device. When the SB221 beeps, it means the headset has associated with the media device.

• On Bluetooth headphones, where is the power button?
  It’s the “3” in the center that you’re referring to. It’s fantastic because all of the functions are located on the same side. If you want to connect to your phone, the center button also serves as a “answer and hang-up” button.

• My Bluetooth headphones aren’t connecting to my phone?
  If your Bluetooth devices won’t pair, it’s probably because they’re out of range or not in pairing mode. Try rebooting your devices or having your phone or tablet “forget” the connection if you’re encountering persistent Bluetooth connection issues.

• What’s the deal with my SoundBot not working?
  First, look inside the charging port; it could be clogged with dust or grime, preventing the gadget from charging properly. If the port is clogged, clean it out with an air duster.

• Why can’t I connect more than one Bluetooth earbud?
  Depending on your audio settings, headphones may only play in one ear. Check your audio properties to make sure the mono option is disabled. Also, make sure that the voice levels on both earphones are equal.

• What is the procedure for resetting my Bluetooth Shower Speaker?
  At the same moment, press and hold the button. The gadget has been reset and will switch off on its own. Finally, push and hold the button to turn on the Bluetooth Speaker. Note: If the gadget is in good working order, do not reset it.

• What is the best way to tell if my Bluetooth headset is completely charged?
  When charging, the indicator light is normally red. When the light goes off, it means the battery has been fully charged. You must master the correct method of charging a Bluetooth headset, that is, only when the Bluetooth headset battery is low, to achieve the longest battery life.\

• What are the steps to resetting my Bluetooth Shower Speaker?
  Press and hold the button at the same time. The device has been reset and will turn off by itself. To turn on the Bluetooth Speaker, press and hold the button. Note: Do not reset the device if it is in good working order.

• I’m not sure how to tell if my Bluetooth headset is fully charged.
  The indicator light is generally red when charging. When the light turns off, it indicates that the battery is fully charged. To get the longest battery life, you must master the proper method of charging a Bluetooth headset, which is to charge it only when the battery is low.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>