SMOOSAT E9 Pro Electric Scooter for Kids Owner’s Manual

June 5, 2024
SMOOSAT

SMOOSAT E9 Pro Electric Scooter for Kids Owner’s Manual

Package Contents

Pre-Assembled Electric Scooter

Package Contents

Accessories

Accessories

Carefully check package contents, if anything is missing or damaged, please contact support@ismoosat.com for help.

Product Overview

Product Overview

Throttle Instruction

Throttle Instruction

Assembly and Set-Up

  1. To release the folding mechanism, place the scooter on the ground, push the release lever down to unfold the scooter.
    Assembly and Set-Up

  2. Using the 5 mm Allen Wrench loosen the handlebar clamp.
    Assembly and Set-Up

  3. Insert the handlebar with the throttle facing the rider.
    Assembly and Set-Up

  4. Using the 5mm Allen Wrench tighten the hanclebar clamp.
    Assembly and Set-Up

  5. To adjust the height of the handlebar, open the quick-release lever and slide the T-bar to the desired position and resecure the quick-release lever to lock into place.
    Assembly and Set-Up

  6. The tension of the quick-release lever can be adjusted by manually tightening or loosening the Allen bolt. Be careful not to overtighten.
    You should always be able to open and close the quick-release lever by hand and the T-bar should slide freely when the quick-release is open.
    Assembly and Set-Up

Charge Your Scooter

Charge Your Scooter

NOTE:

Plug the charger plug into wall outlet,the light on the charger should be green.

The light on the charger should turn red during charging.

When the charging is completed the light will turn green again.

The battery will be fully charged after 5 hours

  1. Lift the rubber plug.
    Charge Your Scooter

  2. Plug the charger into the charging port.
    Charge Your Scooter

  3. When charging is completed, put back the rubber plug.
    Charge Your Scooter

Pairing your Bluetooth Device (for E9 Apex Only)

Music icon To pair with a Bluetooth device
Follow these steps:

  1. Make sure both the Bluetooth® function in your device and the scooter are turned on.
  2. On your device, locate the Bluetooth® device list. Select “SmooSat E9 Apex” from the list.
    Pairing your Bluetooth Device

How to Ride and Stop

Always wear proper protective equipment, such as an approved safety helmet (with chin strap securely buckled), elbow pads, and kneepads. A helmet may be legally required by local law or regulation in your area. A long-sleeved shirt, and long pants are recommended. Always wear shoes and keep shoelaces tied and out of the way of the wheels and motor. Never ride barefooted or in sandals.

  1. Press the power button and hold for 2 seconds to turn on the scooter. Check the power indicator.
    How to Ride and Stop

  2. Step on the deck with one foot, and slowly kick off the other on the ground.
    How to Ride and Stop

  3. When the scooter starts to coast, put both feet on the deck and push down the accelerator.
    NOTE: Do not push down the accelerator before the scooter reach the speed 3 mph, the scooter must be traveling.
    How to Ride and Stop

  4. Tilt your body to the steering direction as you turn, and slowly turn the handlebar.
    How to Ride and Stop

  5. For controlled stops, release the throttle and apply the brake by putting pressure on the rear-fender brake.
    How to Ride and Stop

Customer Support

www.facebook.com/smoosatscooter or scan above QR code

Shenzhen Ruiyundi Tech. Co. Ltd.
Website: www.ismoosat.com
Facebook: www.facebook.com/smoosatscooter
Email: support@ismoosat.com
Tel: +1 929 693 6066
Mon-Fri 9:00 AM – 5:00 PM Pacific Time
Add: 2208-E3, Block A, Lianhe Plaza, No. 5022, Binhe Avenue, Fushan Community, Futian District, Shenzhen, Guangdong, China.

Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals