ONN ONA21DP001A 9” Portable DVD Player with Swivel Screen User Manual

ONN ONA21DP001A 9” Portable DVD Player with Swivel Screen User Manual

IMPORTANT SAFETY INSTRUCTIONS

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THECOVER (OR BACK). NO USER SERVICEABLE PART INSIDE, REFERSERVICING TO QUALIFIED SERVICE PERSONNEL.

DANGEROUS VOLTAGE: The lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to persons.

ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSETHIS UNIT TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

Before using the unit, be sure to read all operating instruction carefully, please note that these are general precautions and may not pertain to your unit. For example, this unit may not have the capability to be connected to an outdoor antenna.

1. Read these instructions
   All the safety and operating instructions should be read before the appliance is operated.

2. Keep these instructions
   The safety and operating instructions should be kept for future reference.

3. Heed all warnings
   All warnings on the appliance and in the operating instructions should bead hered to.

4. Follow all instructions
   All operation and use instructions should be followed.

5. Do not use this apparatus near water
   The appliance should not be used near water; for example, near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

6. Clean only with dry cloth
   The appliance should be cleaned only as recommended by the manufacturer.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
   Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or similar surface. This product should never be placed near or over a radiator or heat source. This product should not be placed in a built in installation, such as a book case or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments / accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. An appliance and cart combination should be moved with care. Quick stop, excessive fore and uneven surfaces may cause the appliance and cart combination to overturn.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.
    To protect your product from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Power source
    This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other source, refer to the operation instructions.

16. Power lines
    An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading
    Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and liquid entry
    Never push objects of any kind into the product through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product.

19. Service
    Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Replacement parts
    When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts. Unauthorized substitutions may result in fire or electric shock or other hazards.

21. Safety check
    Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

22. Damage requiring service
    Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions.

23. When the power- supply cord or plug is damaged.

24. If liquid has been spilled or objects have fallen into the product.

25. If the product has been exposed to rain or water.

26. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an adjustment of other controls may result in damage and will require extensive work by a qualified technician to restore the product to its normal operation.

27. If the product has been dropped or the cabinet has been damaged.

28. When the product exhibits a distinct change in performance- this indicates a need for service.

NOTE: Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any way such as the following: the power-supply cord or plug has been damaged, liquid has been spilled into unit, the unit has been exposed to rain or moisture, the unit has been dropped or the unit does not operate normally.

Minimum 20cm distances around the apparatus for sufficient ventilation;
No naked flame sources, such as lighted candles, should be placed on apparatus;
Attention should be drawn to the environmental aspects of battery disposal ;
The apparatus shall be used in moderate climates.

Warning:

• Danger of explosion if battery is incorrectly replaced.
• Replace only with the same or equivalent type.
• The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
• To avoid battery subjected to extremely low air pressure.
• The mains plug of power adapter is used as the disconnect device, The socket outlet shall be installed near the equipment and shall be easily accessible.
• The USB port does not support USB charging for external circuit.
• The maximum operation temperature is 40°C.
  To prevent possible hearing damage, do not listen at high volume levels for long periods.

LOCATION OF CONTROLS

Function Panel View:

1. MENU : Press to enter root menu.
   SOURCE : Press and hold to switch to “AV IN” mode, press and hold again to resume.

2. VOL +: Press to increase volume.
   SETUP: Press and hold to enter set up menu.

3. VOL- : Press to decrease volume.
   STOP: Press and hold to pre-stop playing, press and hold again to stop playing completely.

4. Press to turn upward.
   Press to skip to previous track.
   Press to turn downward.
   Press to skip to next track.
   Press to turn left.
   Press to fast backward.
   Press to turn right.
   Press to fast forward.
   Press to start playing or pause, press again to resume during playing.
   Press to confirm the operations.

5. Press to open the disc door.
   Right Side View:
   
   

6. USB Port

7. SD/MMC/CARD Slot

8. EARPHONE Jack

9. AV OUT Jack

10. AV IN Jack

11. POWER ON/OFF Switch

12. DC IN Jack
    Front Side View:
    
    

13. CHARGE Indicator

14. Remote Sensor

15. POWER Indicator

REMOTE CONTROL

1. POWER Button
2. VOLUME +/– Buttons
3. MUTE Button
4. MENU Button
5. Direction Buttons
6. (Skip Forward) Button
7. (Fast Forward) Button
8. (Play/Pause) Button
9. USB/CARD Button
10. TITLE Button
11. (STOP) Button
12. AUDIO Button
13. GOTO Button
14. REPEAT Button
15. SLOW Button
16. LCD ON/OFF Button
17. Numeric Buttons
18. SETUP Button
19. (Skip Backward) Button
20. (Fast Backward) Button
21. OSD (On Screen Display) Button
22. SUBTITLE Button
23. ANGLE Button
24. PROG (Program) Button
25. OK Button
26. STEP Button
27. ZOOM Button
28. A-B Repeat Button

BATTERY INSTALLATION (REMOTE CONTROL)

Battery installation:

1. Press the tab on the battery door and lift it off.
2. Install two (2) x AAA size batteries into the battery compartment as the figure on right and the polarity markings inside battery compartment.
3. Replace the battery door.
   

Battery Precautions:

Follow these precautions when using a battery in this device:

1. Use only the size and type of battery specified.
2. Avoid replacement of a battery with an incorrect type.
3. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. A reversed battery may cause damage to the device.
4. Do not mix different types of batteries together (e.g. Alkazline and Carbon-zinc) or old batteries with fresh ones.
5. If the batteries in the device are consumed or the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
6. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s directions).
7. Don’t disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a Battery.
8. Don’t leaving a battery in an extremely high temperature surrounding Environment.
9. To avoid battery subjected to extremely low air pressure.
10. Clean the battery contacts and also those of the device prior to battery installation.

Remote Control Sensor:

Remarks:

1. When there is an obstacle between the unit and the transmitter, the transmitter may not operation.
2. When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on remote control of the unit, the remote operation may be unstable.

POWER SOURCE

Charging by supplied AC/DC Adaptor:

1. Connect the small plug from the supplied AC/DC Adaptor to the DC IN Jack on the right of unit.
2. Connect the AC/DC Adaptor to the wall outlet having AC 100-240V~; 50/60Hz.
3. During charging, the red indicator will light, and it will turn green when finished charging.

Notes: For saving energy, unplug the AC/DC Adaptor from wall outlet if the unit will not use for long period of time.

Your battery will last longer if you follow these simple guidelines for caring and storing it:

1. Do not overcharge (longer than 24 hours). Excessive charging or discharging may shorten the battery’s life.
2. Battery life naturally shortens slowly over time.
3. The rechargeable battery incorporated in this product is not user replaceable.

Charging by the supplied Car Adaptor:

1. Connect to the cigarette lighter socket of a vehicle that has a 12V battery as the figure below.
   It is not compatible with a vehicle that has a 24V battery.

2. This is a special negative grounded Car Adapter. Using this Car Adapter with a plus grounded car can cause malfunction.

3. Do NOT plug in the Car Adapter until the car ignition is turned on.

4. Disconnect the Car Adapter from the cigarette lighter and the unit after use.
   

CONNECTIONS

Connecting to a TV or Video Player (such like DVD; VCR; DVR Players … ) with AV connection cable.

NOTE:

• The default setting of the unit is AV Out, if connect to external Video Player (such like DVD; VCR; DVR Players … ), press and hold the SOURCE button to set to AV IN mode (“AV IN” will appear on the screen), press and hold again to resume.
• Using the Earphone (not included) to listen privately.

SWIVEL PANEL

The viewing angle of the swivel panel can be adjusted as below as desired:

OPERATIONS

1. Lift up the panel and turn to desired angle. Slide the Power ON/OFF switch to “ON” position to power on the unit, the green Indicator on front of the player will light.

2. Press the OPEN button to open the disc door. Place the disc on the center spindle with label side facing up. Close the disc door and the player will start playback automatically. If this doesn’t occur, press the button.

3. During playback:

   • Press the or buttons on remote control repeatedly to fast search for a specific section forward/backward.
     Press button on remote control to resume normal playback.

   • Press the or button on remote control repeatedly to skip to specific track or chapter.

   • Press button on remote control to pause, press button again to resume normal playback.

   • Press the VOL (Volume) +/- buttons on remote control to adjust volume level.

   • Press the STOP button on the remote control to pre-stop. The player will remember the point where the disc was stopped. When press button again, playback will start from this point. Press the STOP button twice to stop completely, press button to start from beginning.

4. For saving energy, always power off the player by slide the Power ON/OFF switch on the player to OFF position or unplug the wall power adaptor from player and wall outlet.)

Repeat Playback: (DVD)

• Press the REPEAT button once, the current chapter will playback repeatedly and continuously.
• Press the REPEAT button twice, the current Title will playback repeatedly and continuously.
• Press the REPEAT button the third time, all files will playback repeatedly and continuously.
• Press the REPEAT button repeatedly to turn off the repeat mode.

Repeat Playback: (CD)

• Press the REPEAT button once; the current track will playback repeatedly and continuously.
• Press the REPEAT button twice; all the tracks on the disc will playback repeatedly and continuously.
• Press the REPEAT button repeatedly to turn off the repeat mode.

(CD/DVD)Program:

1. During CD or DVD playback, press the 352* (Program) button.
2. Using the Direction, OK and Numeric buttons to select and set the desired T (Title), C (Chapters), tracks (for CD) of the movie /music you wants. The Program menu will appear as follows.

3. Using the Direction buttons to select and highlight the “CLEAR” or button on the screen then press the OK button to clear all the programmed items when there is wrong programming.
4. Using the Direction buttons to select and highlight the “PLAY” or button on the screen then press the OK button to start program playback.

OPERATIONS

• LCD ON/OFF: Press to turn on or off the LCD display.

• POWER: Press to turn to standby mode. Press again to turn on.

• Volume +/–: Press to increase or decrease volume.

• MUTE: Press to turn off the sound, press again to resume.

• MENU: Press to return to disc’s menu page (Function depends on the recording of the disc).

• OSD (On Screen Display) : During playback, press repeatedly to read the information of playback status.

• SUBTITLE: During DVD playback, press repeatedly to select the desired subtitle.
  (Function depends on the recording of the disc)

• STEP: During movie playback, press repeatedly to play the movie frame by frame.
  Press the button to resume normal playback.

• TITLE: Press to return to disc’s title page (Function depends on the recording of the disc).

• ANGLE: During DVD playback, press repeatedly to select the viewing angle. (Function depends on the recording of disc)

• ZOOM:
  During movies playback, press the ZOOM button repeatedly to zoom in/out the picture. When in zoom in mode, press Direction buttons to select the parts of the zoomed picture to watch. (This function is not available on all discs)

• GOTO:

  • Press to display the TT (Title), CH (Chapter) and time selection, input the desired title, chapter or playback time. ( For DVD disc) Press the OK button to confirm.
  • Press to display the TRK (Track) and time selection, input the desired track or playback time. (For audio CD disc) Press the OK button to confirm.

• AUDIO:

  • During DVD playback, press repeatedly to select the desired audio language. (Function depends on the recording of disc)
  • During CD playback, press repeatedly to select the desired audio channel. (Function depends on the recording of disc)

• A-B Repeat:
  During Playback, press the A-B button to define where you want the section to start. Press the A-B button again to define where you would like the section to end, the unit will then plays the selected section repeatedly and continuously. Press the A-B button again to resume normal playback.
  (This function is not available on all discs)

• LOW:
  During playback, press the SLOW button repeatedly to set the slow motion speed. Press button resume to normal playback.

USB or SD/MMC CARD PLAYBACK

1. Insert the USB device or SD/MMC memory card into the USB port /card slot as the figure below.
   
   NB: The unit supported to playback:

   • MP3; (Music file)
   • JPG (Pictures)
     Make sure correct files were saved in the USB device or memory cards.

2. In Power ON mode, press the USB/CARD button on remote control, the “DVD, CARD, USB” selection window will pop up on the screen. Using the Direction buttons to select and highlight the source then press the OK button to confirm. Using the Direction and OK buttons to select desired Folder or File then press the OK button to start playback.

3. During playback:

   • Press the or button on remote control repeatedly to skip backward/forward.
     Press the or button on remote control repeatedly to fast searching backward/forward.

   • Press the button to pause. Press again to resume normal playback.

   • Press the (STOP) button on remote control to return to menu.

SYSTEM SETUP

Press the SETUP button on remote control or press and hold the SETUP button on the unit, the setting menu will appear on the screen as below. During setting, using Direction , , , buttons to select and highlight the function needed to set or reset, press the OK button to confirm the selection. After setting, press the SETUP button to save and exit.

1. If TV System is selected, it can be set to NTSC, PAL or AUTO to match the connected TV.
2. If POWER RESUME is selected and set On, the unit will start playback from the position where the disc was stopped last time.
3. If Screen Saver is selected and set On, the screen saver will come on when the unit idles or the image is paused for several minutes.
4. If TV Type is selected, set the aspect ratio to match the connected TV.
5. If Video is selected, using the Direction and OK buttons to set it to CVBS to match the connected TV.
6. If Default is selected and set it to restore, all settings will be restored to factory setting.

LANGUAGE SETUP:

1. If Osd Language (On Screen Display Language) is selected, using the Direction and OK buttons to set the priority of the available language. (Function depends on the recording of the disc)
2. If Audio Lang (Audio Language) is selected, using the Direction and OK buttons to set the priority of the available language.
3. If Subtitle Lang (Subtitle Language) is selected, using the Direction and OK buttons to set the priority of the available language or set it off.
4. If Menu Lang (Menu Language) is selected, using the Direction and OK buttons to set the priority of the available language of the on screen menu.

SYSTEM SETUP

RATING SETUP:

1. If Password is selected, press the button to highlight , then enter the four default password “0000” to unlock the rating, press the OK button to confirm. Now the lock status will be .
   To change a new password, highlight the password column and enter a new four digit password under unlocking status, press the OK button to confirm password changing.

2. If Rating is selected after unlocking, press the button to enter rating level, press or button to select the desired rating level, then press the OK button to confirm setting.
   ~ Rate levels:
   KID SAFE: Kid safe
   G: All ages
   PG: Parental Guidance
   PG 13: Parental Guidance less than 13 years old
   PG-R: Under 17 years old, Parental Guidance suggested
   R: Under 17 years old, Parental Guidance strongly
   NC-17: 17 years old or above
   ADULT: Adult only

TFT SETUP:
Using the Direction and OK buttons to set or reset the picture quality such as the panel’s Brightness, Contrast, Hue, Saturation.

DIGITAL SETUP:

1. If Dual Mono is selected, using the Direction and OK buttons to set it to Stereo, Mono L, (Plays Left channel on all speakers), Mono R (Plays Right channel on all speakers) or Mix Mono (Mixed Right and Left channel then plays on all speakers) as desired. (Functions depend on the recording of the disc).
2. If Downmix is selected, using the Direction and OK buttons to set it to LT/RT; Stereo as desired.
   • If set to LT/RT, the rear left and rear right channels will plays on both Left andRight Speakers.
   • If set to Stereo, the rear left channel will plays on Left Speaker; the rear right channel will play on Right Speaker.
3. If Dynamic Range is selected, using the Direction and OK buttons to set the dynamic level or turn it off.

CARE AND MAINTENANCE

Caring for Discs

Treat the disc carefully. Handle the disc only by its edges.
Never allow your fingers to contact with the shin , unprinted side of the disc.

• Do not attach adhesive tape, stickers, etc. to the disc label.

• Clean the disc periodically with a soft, lint-free, dry cloth, Never use detergents or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.

• If a disc skips or gets stuck on a section of the disc, it is probably dirty or damaged(scratched).

• When cleaning the disc, wipe in straight lines from the center of the disc to the outer edge of the disc. Never wipe in circular motions.
  

• Discs should be stored in their cases after each use to avoid damage.

• Do not expose discs to direct sunlight, high temperatures or dust, etc. Prolonged exposure or extreme temperatures can warp the disc.

• Do not stick or write anything on either side of the disc. Sharp writing Instruments, or the ink, may damage the surface.

Cleaning the Unit

• To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other furniture. Use caution when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.

TROUBLESHOOTINGS

Check the followings before requesting service:

adapter to the unit or wall outlet.
The unit is in Standby mode| Press the /POWER button to turn on the unit from Standby mode.
No sound| Volume in minimum position| Press the VOL + button to increase the volume level.
The connected device is not in payback mode| Play music/movie in the connected device as usual and make sure the volume level of it is in high level.
Earphone plugged on this player| Unplug the earphones to enable sound from the speaker.
Sound distortion| Volume level too high| Press the VOL – button to decrease the volume level.
Reduce the volume level of the connected device.
There is no picture on the external TV display| Input source incorrect| Select the correct source on the external display.
AV cable is not connected| Connect the AV cable correctly.
There is no picture on the DVD screen| Display is turn OFF| Press the LCD ON/OFF button on remote control to turn ON the display.
AV cable is unpluged and not connected| Plug and connect the AV cable to an external TV screen.
The remote control does not work| No batteries inserted or the battaries were in low position| Insert or replace with new batteries.
Obstacle existed| Remove the obstacle in the transmission path.
Disc not playing| Wrong type of discs or the disc is corrupted| Try other discs.
The disc is dirty or inserted incorrectly| Clean disc and insert with label side up.

SYMBOLS

SPECIFICATIONS

Power adapter information’s

Caution: Please refer for further information to the user manual. Use only power supplies listed in the user instructions.

Manufacturer： SHENZHEN SHI GUANGKAIYUAN TECHNOLOGY., LTD.
Commercial Registration No. :91440300053998927W
Address: 2 floor, 41 TianSheng Road, TianLiao village, GongMing Street, Guangming, Shenzhen, Guangdong, P.R. China

Model No.: GKYZA0100120UK
Input: 100-240V~ 50/60Hz 0.5A
Output: 12.0V 1.0A 12.0W
Average active efficiency: 84.08%
No-load power consumption: 0.042W
Efficiency at low load (10%)： 81.58%

Disc Compatibility: DVD/SVCD/DVCD/CD/CD-R/CD-RW/DVD±R/DVD±RW

ACCESSORIES

• 1 x User’s Manual
• 1 x Power Adapter
• 1 x Car Adapter
• 1 x Remote Control
• 2 x AAA Batteries

SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE!

Free 1 year guarantee

All our electrical items are covered by a full 1 year guarantee from the day you buy it. In the unlikely event that your product is faulty or you are simply struggling to set it up, don’t worry, here’s what you do:

1. If you experience any problems please contact our technical help line who will be happy to help. Please note this is not a free phone number.
2. If the problem can’t be resolved, you will receive a reference number.
3. Take the reference number along with the item, all its components and your receipt to your nearest store for a full refund.

Need something else?
There are a wide range of accessories and other products that can be ordered direct to your door. For more information see www.asda.com

DECLARATION OF CONFORMITY

Hereby, declares that the radio equipment type Onn DVD is in compliance with Directive 2014/35/EU, 2014/30/EU.

The full test of the EU declaration of conformity is available at the following internet address: http://www.asda.com

RECYCLING

This product bears the selective sorting symbol for
Waste electrical and electronic equipment (WEEE).

This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

User has the choice to give his product to a competent recycling organization or to the retailer when he buys an new electrical or electronic equipment.

References

• Asda.com - Online Food Shopping, George, & more

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>