onn Wireless On Ear Headphones with Rotating Boom Microphone User Guide
- June 3, 2024
- Onn
Table of Contents
onn Wireless On-Ear Headphones with Rotating Boom Microphone
Get to Know Your Wireless Headphones
- Model: 100070290
- peaker Rated Input Power: 10mw
- Speaker Diameter: 30mm
- Speaker Impedance: 32±15%
- Speaker Sensitivity: 96±4dB
- USB-C Charging cable: 6 ft (1.8 m)
What’s in the Box?
Check to make sure you have everything below
- 1 Wireless On-ear Headphones
- 1 USB C Charging Cable 6 ft (1.8m)
- 1 Quick Start Guide
Let’s Get Started!
-
First time set-up
-
Step 1: Press and hold for 5 seconds to begin pairing. The LED will alternatively flash blue and red.
-
Step 2: Open Bluetooth setting on your device and select “onn. HEADSET” to get it connected.
-
Power On: Press & Hold 3 sec, LED light turns blue
-
Power OFF :Press & Hold 4 sec, LED light turns red
-
Reset: Restore factory defaults
Dual-point connectivity Connect two devices simultaneously
- To pair the headset with two devices, begin by connecting the headset to one device using the previous instructions. Once device #1 is connected, disable Bluetooth on the paired device #1 and the headset will automatically re-enter pairing mode.
- Place device #2 into pairing mode and connect to device #2.
- Re-enable Bluetooth connection on device #1 and the headset will automatically connect to both devices. Now your headset can be used simultaneously with two devices.
Enjoy Your Music
- Press & Hold Next Song
- Press & Hold Previous Song
- x1 Press Volume Up
- x1 Press Volume Down
- x2 Press Siri/Google Assistant
Take a Clear Phone Call
- x1 Press Answer Call
- x1 Press Hang Up
- Press & Hold Reject Call
- x1 Press Volume Up
- x1 Press Volume Down
- Mute Switch When mute should show red color
Charge Your Headphones
Headphones charging
- Headphones charging: Red light on
- Headphones fully charged: Blue light on
- While charging, the headphones are inoperable. 5V 0.5A
The Fine Print
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
- The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Warning:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. Need help? We’re here for you every day from 7 a.m.-9 p.m. CST.
Give us a call at 1-888-516-2630
Produced for Walmart Inc. Bentonville, AR 72716
We’d love to hear from you. Scan with your smartphone camera and let us know what you think.
Wireless On-Ear Headphones With Rotating Boom Microphone Quick Start Guide
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>