Gude 40123 Ratchet Screwdriver Instruction Manual

Gude 40123 Ratchet Screwdriver

product safety, commands

Ratchet screwdriver 1/2″
Hardy, chromium-plated, polished finish. Extremely high torque (110 Nm), owing to which additional tightening is not necessary. Softgripp heated handgrip. Tool bracket of high quality. Low vibrations, long-life gearing right/left from the gear on the head. Air outlet on pneumatic coupling to provide for nice work. Continuous adjustment of speed. It includes a connecting plug of a usual nominal width 7,2.

Unit Scope of Supply

1. Handle
2.  Pneumatic coupling
3.  Control lever
4.  Tool hold

START / STOP

Guarantee

Guarantee claims according to the guarantee certificate attached. Please, understand that we are unable to accept the guarantee for the following reasons:

•  Breach of operation and service instructions.
• Necessary cleaning neglect.
•  Forcible use, unprofessional handling, misuse or accident.
•  Laic interventions or unprofessional attempts to do a repair.

General Safety Directions

Read the operation manual carefully. Get familiar with the adjustment and correct use of the unit

Assigned Use
The adjustment screwdriver is a pneumatic tool to do craft works easily. It works very well on motor vehicles, motorcycles, agricultural machines or assembly belts, primarily on hardly accessible places. To obtain maximum torque, additional fastening by hand with a ratchet screwdriver is not permitted. Waste air comes out in the forward part of the body. Pneumatic coupling is formed by fast-acting clutch.

Safety Provisions
Protect yourself and those around you against accidents with suitable safety means.

•  Do not touch the rotating parts.
•  The ratchet screwdriver should not be used in contrary to determination.
•  Protect the pneumatic tools from children.
•  Get down to work well-rested and concentrated.
•  Pneumatic connection via a fast-acting clutch only.
•  Set up the work pressure on the reduction valve.
•  Do not use oxygen or inflammable gases as the source of energy.
•  Before removing failures, disconnect the unit from the source of pressurized air.
•  Use only genuine spare parts.
•  Never let the unit idle at full.
•  When working with a ratchet screwdriver, always wear the required protection suits and ear protectors.

Technical Data

• Operating pressure: 6,3 bar
• Air consumption: 114 l/min
• Air connection crew thread: 1/4″
• Max. torque: 68 Nm
• Speed: 160 min-1
• Recommended hose Cross-section : 10 mm
• Weight net/gross: 1,2 kg/1,3 kg

Initial Operation

Screw the plug-in clutch included in the delivery (pos. 2) and screw in the reduction clutch. Use a box-end or a forked wrench for it.
Notice: Tighten the thread with Teflon tape. Pull a required socket wrench insert on the drive (pos.4). Connect the air hose and a fast-acting clutch to the plug-in clutch. Put the socket wrench insert on the screw or the nut being released/tightened. Set-up the required direction of turning on the switching lever (Fig.2) and pull the draw-off lever (pos. 3). The required speed and torque may be set up with a screw on the hand grip (Fig. 3).

Maintenance and Care

Observing warning commands shown in the manual will provide this high-quality product long service life and fault-free operation. The lasting and troublefree function of your ratchet screwdriver is grounded on regular lubrication. Use only a special tool oil. Pick up a possibility of lubrication. :

• Via a beam-added lubricator
  The full maintenance unit includes a beam added lubricator and is placed on the compressor.

• Via a lubricator on the piping
  A lubricator installed on piping supplied the unit with a sufficient amount of oil in an immediate distance from the unit (approximately 50 cm).

• manually
  If there is no maintenance unit or a lubricator on piping, 5-6 drops of oil should be put in a pneumatic connection before every putting in operation. Store the pneumatic tool in dry rooms only.

Translation of the EC-Declaration of Conformity

We, hereby declare the conception and construction of the below-mentioned appliances correspond – at the type of construction being launched – to the appropriate basic safety and hygienic requirements of

EC Directives.
In case of any change to the appliance not discussed with us the Declaration expires.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>