Industria Fueguina De Relojeria Electronica E2021 Smartphone User Guide

Industria Fueguina De Relojeria Electronica E2021 Smartphone

Product appearance

Hold the power button for a few seconds to turn on the product

1. Front camera

2. Receiver

3. Light & distance sensor

4. SIM slot

5. Touch screen

6. Volume button

7. Power key & Fingerprint

8. Quad camera

9. flash light

10. Speaker

11. USB jack & Headphone jack

12. Microphone

13. Microphone

14. Power key & Fingerprint

Install SIM cards

This product only applies to Nano- SIM and Nano-SIM (Micro SD)
Insert non-standard card may cause damage to the SIM card slot.

• Please turn off your phone before you insert the card.
• When you insert the card, please pay attention to the gap direction andkeep the card balanced.
• If the Nano card and the Micro SD card share the same card slot, the slot is compatible with two cards, but the two cards cannot be placed at the same time.
• Please use the PIN needle carefully to prevent injury to the fingers or damage the phone. Please put the PIN needle on somewhere children can’t reach so as to prevent the children from accidentally swallowing or stabbing themselves.

Charge the battery

Please charge at the first time using this product.

Notice:
When charging, the charger should remain close to the power outlet.

Navigation key
Use the navigation key at the bottom of the screen to operate
the device. This nevigation key is hidden by default, if you want
to cancel this hidden function, please change it in setting.
BACK: Return to last page_
HOME: Return to home page
MENU: Open recent used apps paqe

Safety Precautions

Do not place the phone and battery near or inside the heating device, cooking equipment or high pressure vessel(such as microwave oven, induction cooker, electric oven, electric heater, pressure cooker, water heater, gas stove and etc.), to prevent the battery overheating explosion.

Please use original chargers, cables and batteries. Using non-original chargers, cables or batteries without manufacturer’s certification may cause electric shock, fire, explosion, or other hazards.

To avoid squeezing the device

Do not place heavy objects on the device or squeeze the device vigorously to avoid damage to the device or cause distortion of the touch screen. At the same time, please do not put the device in the pocket for a long time.

The thermal phenomenon of device after long use
The device may become hot when it is used for a long time, such as a long call, battery charging or browse the web. This is a normal phenomenon, not the failure of the device, please do not worry.

Notice:
Access to the Internet, send and receive messages, upload and download, automate synchronization, use certain applications or location-based services may incur additional costs. To avoid additional costs, please contact the service provider and select the appropriate service.

FCC compliance statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Important: Changes or modifications to this product not authorized by INDUSTRIA FUEGUINA DE RELOJERIA ELECTRONICA SA could void the electromagnetic compatibility (EMC) and wireless compliance and negate your authority to operate the product.
This product has demonstrated EMC compliance under conditions that included the use of compliant peripheral devices and shielded cables between system components. It is important that you use compliant peripheral devices and shielded cables between system components to reduce the possibility of causing interference to radios, televisions, and other electronic devices.

SAR Statement:

This Smart Phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.

FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: SmartwayF1 (FCC ID: 2ALP3F1) has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the handset kept 10mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>